Unconfigured Ad Widget

Collapse

.510 DTC load data for Windrunner rifle.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bomb_on_bus
    Calguns Addict
    • Jun 2009
    • 5492

    .510 DTC load data for Windrunner rifle.

    Well I am looking to start reloading for the .510 DTC and have pretty much everything set up to begin except load data.

    I have Winchester BMG brass 06-08 markings that have been trimmed to DTC Case length specs.

    The powder is IMR5010 and WC860.

    Bullets are Hornaday AMAX 750 and Barnes 750 solids and M33 ball for plinking.

    Primers are CCI No.35 .50BMG primers.

    Rifle is a EDM ARMS M96 chambered in .510DTC.

    From what I have read the load data for the 510DTC is the same as for the BMG and from what I have read a good place to start is 210-215 gr of podwer and work my way up in increments of 1-2 gr with the max load being around 235 gr of powder.

    Also looking for loaded ammo overall length data as well. From what I have understood the cases can be trimmed .100, loaded and fireformed in the .510DTC chamber.

    Really interested in load data and info from fellow .510DTC Windrunner shooters as well.
    Last edited by bomb_on_bus; 09-19-2011, 4:01 PM.
    Originally posted by aklon
    In 1775 we stood up.

    In 1776 we announced we would not be sitting back down.

    sigpic
    Ahhhhhhhhhhh! Man that was some great Kool-Aid.......... hmmmmmm theres a hint of something metallic. Oh well guess I will get on with the voting.
  • #2
    joefreas
    • Jan 2010
    • 2421

    Here is a thread about forming the DTC. I will post some load data in a sec. http://www.calguns.net/calgunforum/s...d.php?t=215257

    1.jpg
    2.jpg
    3.jpg
    Last edited by joefreas; 09-19-2011, 4:14 PM.
    If you think nobody cares if you're alive, try missing a couple of payments.

    Originally posted by XDRoX
    Walking around with a banana in a holster won't do anything but get you laughed at.
    "A true patriot would repeal the patriot act"
    Ron Paul

    Comment

    • #3
      bomb_on_bus
      Calguns Addict
      • Jun 2009
      • 5492

      Thanks for the info!

      Anyone else out there doing hand loads for their Windrunner?

      Also a lot of vendors I have run across lately do not sell BMG ammo components to CA anymore. Anyone have a vendor they go through for surplus brass?
      Originally posted by aklon
      In 1775 we stood up.

      In 1776 we announced we would not be sitting back down.

      sigpic
      Ahhhhhhhhhhh! Man that was some great Kool-Aid.......... hmmmmmm theres a hint of something metallic. Oh well guess I will get on with the voting.

      Comment

      • #4
        joefreas
        • Jan 2010
        • 2421

        Contact CSACAnnoneer last I talked to him he had several thousand rounds. I usually buy lehigh bullets from their website. I do like h50bmg powder, I can't get consistent velocities out of the other powders that I have tried.

        Also check out the FCSA they have tons of info on 50 cal rifles
        If you think nobody cares if you're alive, try missing a couple of payments.

        Originally posted by XDRoX
        Walking around with a banana in a holster won't do anything but get you laughed at.
        "A true patriot would repeal the patriot act"
        Ron Paul

        Comment

        • #5
          bomb_on_bus
          Calguns Addict
          • Jun 2009
          • 5492

          Sweet!

          I will drop CSAcannoner a line.
          Originally posted by aklon
          In 1775 we stood up.

          In 1776 we announced we would not be sitting back down.

          sigpic
          Ahhhhhhhhhhh! Man that was some great Kool-Aid.......... hmmmmmm theres a hint of something metallic. Oh well guess I will get on with the voting.

          Comment

          • #6
            50 Shooter
            Senior Member
            • Oct 2005
            • 1653

            I'm not sure if Ben (MrKubota) posts here still, I think he does but he's probably the BEST source of info for loading the 50 DTC. PM him and ask, if you live in the SoCal area (near redlands) you might be able to drop by his place and learn some tips.

            You'll probably find that 220-222 grs. of powder will be a good load for your Windrunner. Just watch for pressure signs as you're working the loads, if you get flattened primers or brass that's hard to eject, back off a couple grs.
            50 BMG Shooters http://50-bmg.com/forum/index.php

            Comment

            Working...
            UA-8071174-1