Unconfigured Ad Widget

Collapse

More beginner questions...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Lazyme
    Member
    CGN Contributor - Lifetime
    • Apr 2011
    • 669

    More beginner questions...

    ...
    Last edited by Lazyme; 05-07-2016, 10:27 AM.
    Weeeeeeeee
  • #2
    scrat
    Senior Member
    • Apr 2007
    • 1516

    need to know what powder. As far as the maximum length you will have to try chambering a round if it goes in too hard then it might be too long. A method of measuring chamber length for your rifle is to take a recently fired round press in a bullet a little long no powder. then chamber the round let the rifle press in the bullet some more then measure and go back about 5 thousands of inch. that will be for that given bullet. Most 30-30 rounds i make are around 29 grains of powder depending on powder H4895 is very good powder for that
    sigpic

    Comment

    • #3
      Whiterabbit
      Calguns Addict
      • Oct 2010
      • 7602

      Depends on the powder. Supposedly there are many powders out there that can be easily and safely used for reduced loads. Others, not so much.

      A good way to find out what other people are doing is to type your powder name into google along with reduced loads. Usually, I'll either find absolutely nothing on the topic, a resounding "I always use this stuff for my reduced loads for X cartridge and it's awesome" or "There's no way in hell loading X cartridge with Y powder in a reduced load is a good idea!". And if it's not, eventually, someone will discuss why, which of course you'd then corroborate with real data from a guide or powder manufacturer.

      Comment

      • #4
        Whiterabbit
        Calguns Addict
        • Oct 2010
        • 7602

        COAL is supposed to be a second order factor for accuracy compared to bullet selection and powder charge. You'll even find folks on this board that develop a round down to the level of insensitivity to powder charge (i.e. wide variances in powder charge lead to no change in accuracy. So they claim.).

        Bottom line, it's possible that being far off the lands is not a problem for one or all of your guns. That's part of the fun. My suggestion would be to compare .005 off the lands of both guns to SAMMI minimum (sanity check) and where the cannelure sits (if present, also sanity check). Unless you have a really strange bullet, you shouldn't have any choice that results in a strange cartridge.

        Not necessarily for accuracy, but just to learn your guns. If you are that kind of person (I am!)

        I would be surprised if you couldn't find a load that shoots minute-of-deer in both rifles with extreme ease.

        edit: FYI I can't find a bullet that will not chamber in my bolt rifle due to COAL (in short, the bullet falls out of the casing before it contacts the lands) and my rifle, bench rested, on sand bags, cold barrel, and minimal coffee before driving to the range, will lay down cloverleaf shaped groups at 100 yards, and I'm no special shooter. I'm not saying you will too, I'm just saying you might not have to be crazy about COAL to get deer-heart accuracy.
        Last edited by Whiterabbit; 09-16-2011, 4:41 PM.

        Comment

        • #5
          scrat
          Senior Member
          • Apr 2007
          • 1516

          +1 on what he said
          sigpic

          Comment

          • #6
            Fjold
            I need a LIFE!!
            • Oct 2005
            • 23094

            As long as they fit in your gun, shoot them. That's not enough of a reduced load to worry about and the location of the crimping groove is unimportant.
            These are some 375 H&H practice loads for my rifle:
            Frank

            One rifle, one planet, Holland's 375




            Life Member NRA, CRPA and SAF

            Comment

            • #7
              Lazyme
              Member
              CGN Contributor - Lifetime
              • Apr 2011
              • 669

              ...
              Last edited by Lazyme; 05-07-2016, 10:28 AM.
              Weeeeeeeee

              Comment

              Working...
              UA-8071174-1