Unconfigured Ad Widget

Collapse

Case trimming

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • BajaJames83
    Calguns Addict
    • Jun 2011
    • 6047

    Case trimming

    Q: I am reloading 223/556 cases full length for 2 different ar's. ive already reloaded some of the brass 5 or 6 times without case trimming. how do i know if the cases need trimming? do they need to be trimmed for these rifles?
    NRA Endowment Life Member
    USMC 2001-2012

    Never make yourself too available or useful...... Semper Fidelis

    John Dickerson: What keeps you awake at night?
    James Mattis: Nothing, I keep other people awake at night.

  • #2
    kmca
    Senior Member
    • Oct 2005
    • 2371

    You're going to have to measure them. If they've never been trimmed, it's almost guaranteed that they will need it. They need to be trimmed for any firearm.

    Comment

    • #3
      popeye4
      Senior Member
      • Nov 2008
      • 1534

      Trim after resizing. Check to make sure the cases aren't stretching and developing a thinning area just above the case head (inside). My experience is that you might be getting close to end of life on the cases at 5 or 6 loadings.
      sigpic
      NRA Life Member
      CRPA Life Member

      Comment

      • #4
        Full Clip
        I need a LIFE!!
        • Dec 2006
        • 10266

        I would scrap them and start with new (or once-fired) brass. Always measure and trim before reloading.

        Comment

        • #5
          FX-05 Xiuhcoatl
          Veteran Member
          • Jun 2011
          • 3162

          Originally posted by kmca
          You're going to have to measure them. If they've never been trimmed, it's almost guaranteed that they will need it. They need to be trimmed for any firearm.
          Only two defining forces have ever offered to die for you, Jesus Christ and the American Soldier.
          One died for your soul, the other for your freedom.

          sigpic

          Comment

          • #6
            gunboat
            Veteran Member
            • Apr 2008
            • 3288

            Buy yourself a universal "case length gage" , a caliber specific case length gage, a caliber specific case length/ headpace gage or a set vernier calipers.
            Autos often stretch cases more than bolt weapons so it is reasonable to think your cases may need to be trimmed. It is not an absolute certainty though.
            my tuppence

            Comment

            • #7
              Striker9
              Junior Member
              • May 2011
              • 18

              Buy yourself one of these. I use Dillon but you can find others on Midway. Takes all guesswork out and faster than measuring every one. My experience is that after sizing, especially using a small base die, you will need to resize.

              Shop Dillon Precision for premium reloading presses, dies, conversion kits, parts, accessories and reloading equipment. Trusted by reloaders for decades.

              Comment

              • #8
                CSACANNONEER
                CGN/CGSSA Contributor - Lifetime
                CGN Contributor - Lifetime
                • Dec 2006
                • 44094

                Danger. Danger Will Robinson.

                If you have really loaded bottleneck brass without checking the length, you have been playing with fire. I find the most stretching tends to be with once fired brass. If you end up loading brass that is too long, it can grow past the end of the chamber and grab the bullet before it leaves the casing. This, in turn, will cause excessive pressure. So, before you even think of doing this again, ask yourself how important your rifle is to you? It could blow up. Also, you might want to consider what you would do if you lost a hand, part of your face, an eye, etc. In the end, it's not worth the risk. Whoever taught you to reload should really be ashamed of themself.
                NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                California DOJ Certified Fingerprint Roller
                Ventura County approved CCW Instructor
                Utah CCW Instructor


                Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                sigpic
                CCW SAFE MEMBERSHIPS HERE

                KM6WLV

                Comment

                • #9
                  BajaJames83
                  Calguns Addict
                  • Jun 2011
                  • 6047

                  well looks like i need to get some case guages, and start measuring asap.....
                  NRA Endowment Life Member
                  USMC 2001-2012

                  Never make yourself too available or useful...... Semper Fidelis

                  John Dickerson: What keeps you awake at night?
                  James Mattis: Nothing, I keep other people awake at night.

                  Comment

                  • #10
                    mrlonewolf
                    CGSSA Director - C3 Leader & Regional Gun Show Booth Coordinator (LA/OC/IE)
                    CGN Contributor - Lifetime
                    • Jul 2008
                    • 4003

                    Originally posted by Full Clip
                    I would scrap them and start with new (or once-fired) brass. Always measure and trim before reloading.
                    Originally posted by CSACANNONEER
                    Danger. Danger Will Robinson.

                    If you have really loaded bottleneck brass without checking the length, you have been playing with fire. I find the most stretching tends to be with once fired brass. If you end up loading brass that is too long, it can grow past the end of the chamber and grab the bullet before it leaves the casing. This, in turn, will cause excessive pressure. So, before you even think of doing this again, ask yourself how important your rifle is to you? It could blow up. Also, you might want to consider what you would do if you lost a hand, part of your face, an eye, etc. In the end, it's not worth the risk. Whoever taught you to reload should really be ashamed of themself.

                    ^^^^ This.

                    Originally posted by jhkutterer
                    well looks like i need to get some case guages, and start measuring asap.....
                    ^^^^ And of course this.....
                    Would you like to participate in the Right to Keep and Bear Arms movement in California?
                    Please visit the Calguns Community Chapter forum for your area and sign the roll call
                    California needs YOU.


                    sigpic

                    Prepare for the unknown by studying how others in the past have coped with the unforeseeable and the unpredictable. George S. Patton

                    Comment

                    • #11
                      damndave
                      I need a LIFE!!
                      • Oct 2008
                      • 10858

                      Originally posted by CSACANNONEER
                      Danger. Danger Will Robinson.

                      If you have really loaded bottleneck brass without checking the length, you have been playing with fire. I find the most stretching tends to be with once fired brass. If you end up loading brass that is too long, it can grow past the end of the chamber and grab the bullet before it leaves the casing. This, in turn, will cause excessive pressure. So, before you even think of doing this again, ask yourself how important your rifle is to you? It could blow up. Also, you might want to consider what you would do if you lost a hand, part of your face, an eye, etc. In the end, it's not worth the risk. Whoever taught you to reload should really be ashamed of themself.



                      Process for bottleneck cases should be as such. I SS media tumble so might be a little different.

                      1: Decap old primer
                      2: Tumble
                      3. FL resize
                      4: Tumble to get lube off, or wipe by hand
                      5: Trim and measure
                      6: Chamfer & deburr
                      7: Prime
                      8: Powder charge
                      9: Seat bullet
                      10. Measure & check through a case gauge

                      Between all these steps, you should always be on the lookout for pressure signs.

                      I also uniform the primer pocket and deburr the flash hole. Not necessary, so I left that out.

                      Comment

                      • #12
                        BajaJames83
                        Calguns Addict
                        • Jun 2011
                        • 6047

                        ok so im gonnahve to start case trimming.....
                        so what is the easiest and cheaest way to go about this..... i will be loading 223/556 and 308/762 nato rounds.
                        is the lee case gauge and trim set up any good.....
                        NRA Endowment Life Member
                        USMC 2001-2012

                        Never make yourself too available or useful...... Semper Fidelis

                        John Dickerson: What keeps you awake at night?
                        James Mattis: Nothing, I keep other people awake at night.

                        Comment

                        • #13
                          CSACANNONEER
                          CGN/CGSSA Contributor - Lifetime
                          CGN Contributor - Lifetime
                          • Dec 2006
                          • 44094

                          If you are just doing those two cartridges, you might want to look at the possum hollow trimmers. But, if you are ever planning on doing small batches of other bottlenecked cartridges, I'd recommend a lathe type trimmer like a Llyman. Also, there is a lot to know about trimmers. Some trim from a datum point on the case head, some use a point on the inside of the case head and some use a point on the shoulder. There is no right way to do it. You just need to understand what you are doing. If you are trimming mixed headstamped brass, the inside the case head meathod won't give you any consistancy at all. If you are sizing brass at different times (changing out dies and then changing back) you will get inconsistancies from using a trimmer which datums from the shoulder. The bottom of the casehead meathod will give you the best consistancy for OAL. BUT, that doesn't mean it's the best meathod since, what you are ultimately after is a consistant neck length which would mean that the shoulder datum point meathod should be best. Again, that will depend on your individual reloading practices.

                          Also, typically, the more you spend on a trimmer, the quicker and easier it will be for you. I would suggest getting a trimmer which cuts with a "V" type cutter. Then, you won't have to debur the inside and outside of each neck by hand.

                          In the end, I have owned and used many different styles of trimmers but, I have not used a Lee one yet. I keep meaning to buy one just to try it out though. Hell, I've never used the one trimmer (Possum Hollow) that I've recommended but, I know it to be a good type of trimmer. The drawback is that you need a different one for each specific cartridge. I currently use a Giruard, CH4D, Lyman or K&M depending on the cartridge and what I'm trying to accomplish.
                          NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                          California DOJ Certified Fingerprint Roller
                          Ventura County approved CCW Instructor
                          Utah CCW Instructor


                          Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                          sigpic
                          CCW SAFE MEMBERSHIPS HERE

                          KM6WLV

                          Comment

                          • #14
                            21SF
                            Veteran Member
                            • Oct 2010
                            • 3498

                            Its surprising how many people get into reloading before reading a single book or knowing anything!!

                            ITS FREAKIN DANGEROUS.
                            SA TRP Half rail, Glock 21SF, Spikes St-15, Ruger Alaskan .44, Saiga 7.62, GSSF Member
                            Diablo Rod & Gun Club
                            Originally posted by keenkeen
                            "What you've just posted is one of the most insanely idiotic things I have ever read. At no point in your rambling, incoherent post were you even close to anything that could be considered a rational thought. Everyone in this forum is now dumber for having read it. I award you no points, and may God have mercy on your soul."

                            Comment

                            • #15
                              BajaJames83
                              Calguns Addict
                              • Jun 2011
                              • 6047

                              ^ thanks I guess im an idiot...
                              NRA Endowment Life Member
                              USMC 2001-2012

                              Never make yourself too available or useful...... Semper Fidelis

                              John Dickerson: What keeps you awake at night?
                              James Mattis: Nothing, I keep other people awake at night.

                              Comment

                              Working...
                              UA-8071174-1