Unconfigured Ad Widget

Collapse

SINGLE OR MULTI STAGE PRESS?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • gemini1
    Senior Member
    • Nov 2008
    • 2230

    SINGLE OR MULTI STAGE PRESS?

    I was wondering, why do some folks new to reloading, prefer to start with the single stage press then eventually get the multi (4 hole turret?) stage press? Both almost cost the same, and from what I've read, it seems more work needs to be done on a single stage, changing dies, making sure its set correctly etc, etc, whereas on a multi stage, one can just place all the needed dies and just set it once. Am I missing something? I'm planning to start reloading but I'm on the cheapest route, can some of you starters and gurus give some guidance?
    Thanks
  • #2
    Sky_DiveR
    Veteran Member
    • Dec 2008
    • 3017

    Mainly just to keep the starter from getting in over their head too fast. I recommend a single stage mainly as a safety thing. It's too easy to miss or overlook a step and have problems with your loads that, 1) may damage your gun and 2) may cause injury to you or somebody else.

    If you can describe yourself as very precise, patient, and meticulous then you should have no problem with a progressive or turret press. I started off with a progressive loading pistol rounds and was asked the same thing by the shop owner. I also recommend starting off reloading straight walled pistol rounds.

    Nothing wrong with having a single stage press either. I bought one later so I can prep brass and load rifle rounds.

    Comment

    • #3
      bumpo628
      Senior Member
      • Nov 2009
      • 1142

      I think the turret is the way to go.
      Lee has 3-hole (w/o auto advance) and 4-hole (w/ auto advance) turret presses. If you get the 4-hole, remove the auto advance for now. Then you can treat the turret press like a single stage that you only have to rotate the turret to switch to the next stage. You can learn the basics and you won't have to swap out the dies. Changing Lee dies on a single stage would be a pain since the Lee lock rings don't have a set screw. Later you can replace the auto advance if desired. If you get a single stage and get Lee dies, you can either upgrade the lock rings or drill & tap set screws into the rings.
      Last edited by bumpo628; 02-17-2011, 6:59 PM.
      Ronald Reagan once said that the most terrifying words in the English language are: "I'm from the government and I'm here to help".
      Download my alloy calculator here: http://castboolits.gunloads.com/showthread.php?t=105952

      Comment

      • #4
        f4tweet
        Senior Member
        • Oct 2005
        • 2022

        Progressive. Just load one round at a time until you get the hang of it.

        Comment

        • #5
          Bill Steele
          Calguns Addict
          • Sep 2010
          • 5028

          I think the right first press depends on what you want to do.

          I do think the "single stage for beginners" thing is overated.

          On the other hand, if you plan to load a lot of different calibers, including rifle calibers, a single stage press might be a good start as you can always use it for many tasks after you have moved up to something more automated.

          If you are going to start with handgun ammo and don't want to drop a bundle of cash up front, I agree the Lee Classic Turret (cast iron base, 4 holes in turret) is the best way to go. It is super easy to switch calibers (and cheap to do multiple calibers), puts out upwards of a hundred rounds an hour (some claim more, but for me, a hundred an hour is about right) and as you pointed out in your OP, not a great deal more to buy than a single stage press.

          For sure, if you start with a single stage press, get either a Lee Breech Lock or Hornaday LnL press with the quick change bushings, the only way to go with a single stage press.

          If money is not a concern, Dillon progressive is hard to beat.

          If you are going to get Lee stuff, the best prices are here: https://factorysales.com/html/company.html
          Last edited by Bill Steele; 02-17-2011, 7:53 PM.
          When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

          Comment

          • #6
            novalondon
            Member
            • Jan 2010
            • 217

            Like a baby, crawl, walk and then run. Once your single stage has taught you and or you have learned the basics on how to load a good match capable round, then, if needed, you can move up to a progressive and run a ton of loaded ammo safely.
            01-FFL - Restorer and sales of old battle rifles
            Smile, it makes then wonder what your up to !
            Leave it cleaner than you found it, one day you may come back to it.
            Ooh Rah- 1969-1978

            Comment

            • #7
              LGB Loader
              Senior Member
              • Jun 2008
              • 727

              Hate me if you want but I think a single stage should be the first press to get. Get a good strong one and learn the craft. you will always find the need for one even if you have 6 progressives.

              LGB
              Training in The Peaceful Art to achieve unnatural naturalness and natural unnaturalness, BEcoming WATER while serving The Great I AM.

              John 3:16

              Comment

              • #8
                Divernhunter
                Calguns Addict
                • May 2010
                • 8753

                I think you are looking at this wrong. I started reloading in the 1960's and now have 3 single stage presses. One is for 50bmg only. Have I ever felt shorted with them. NO! First I have tried a turret. It is really no gain over the single stage. I batch prep brass and batch reload so this may explain some of it. I have used a Dillon and while you can turn out many rounds I found nothing there for me. I load for more than 35 different cartridges and do not need that many change-overs or even a large number of rounds in a very short time. I can also load a very large number in a short time with the way I reload now anyway.

                As far as adjusting dies. I do not understand where people get this UNLESS they are using lee dies with the non-locking so called locking rings. I have dies I set in the 1960's and have never changed since. They work just as well now as then. Just screw them in and go. With a turret I still have to screw them in and when done take them out so no time is saved. Remember I Batch prep and load so I only need one die at a time.

                I sat down the other day and loaded 1000 rounds of 223, 500 rounds of 204ruger, and 200 rounds of 30-06/6.5X55 and 7mm-08 in one afternoon. I also used an electronic dump/measure for some of them ment for hunting only.

                Plus when doing load development and using 10 different powders you have to measure each one and load 3-5 rounds each. These must be seperated by load so a single stage works as well or better than the others. The Turret I used I ended up just using one die at a time and changeing it when going to the next step in my batch reloading.

                I can honestly say I probably load more ammo than most and have never found a single stage a handicap. It only takes less than 15 sec to change a die so that is no big time saver. Only a fool would do each step to a single round then when it is finished start over, in a single stage or a turret press. So you gain nothing over the single stage.
                A 30cal will reach out and touch them. A 50cal will kick their butt.
                NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
                SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

                Comment

                • #9
                  toby
                  Banned
                  • Jan 2010
                  • 10576

                  If you want to reload and enjoy the experience and be real hands on in every aspect ...then get a single stage. If you just want to crank out ammo ...get a progressive..

                  Comment

                  • #10
                    gemini1
                    Senior Member
                    • Nov 2008
                    • 2230

                    Thanks for the inputs guys, keep 'em coming.
                    I only spend about 400 +/- rounds of 223/5.56 and about 300 rounds of 9mm a month, so this basically would be the rounds I'll be reloading. But I probably would start reloading rifle rounds since this is what I enjoy shooting the most.
                    @Bumpo628, thanks for the info on the 4 hole Lee turret. So this would be like having a single stage if auto advance is set to off, so meaning I can at a leisurely time say just do resizing and depriming all the casings even if I'm not planning to reload all of it at the same time. All the more reason to go for this type of press.
                    Last edited by gemini1; 02-17-2011, 10:11 PM.

                    Comment

                    • #11
                      IntoForever
                      CGSSA Associate
                      • Sep 2010
                      • 3891

                      I have a progressive and one of these http://www.budsgunshop.com/catalog/p...ducts_id/40357. I want to get a 4 hole turret next for the rifles rounds.
                      With all this "gun control" talk, I've not heard one politician say how they plan on taking guns from criminals, just law abiding Citizens.

                      Originally posted by Nose Nuggets
                      5 guys, hot damn thats some good eat'n.
                      Originally posted by pyromensch
                      damn, i duped my own thread...first time i did a poll

                      Comment

                      • #12
                        gemini1
                        Senior Member
                        • Nov 2008
                        • 2230

                        @Divernhunter. Oh man, you've given a valid point. Now I'm back to the this or that? decision choice again.

                        Comment

                        • #13
                          C.G.
                          Calguns Addict
                          • Oct 2005
                          • 8259

                          Originally posted by LGB Loader
                          Hate me if you want but I think a single stage should be the first press to get. Get a good strong one and learn the craft. you will always find the need for one even if you have 6 progressives.

                          LGB
                          Yup, I started on a Rockchucker, then I got the Hornady LNL AP. I still use the Rockchucker for precision rounds and round development. One scenario where you may want to by-pass the single stage if you were to load pistol rounds only.
                          sigpic

                          Comment

                          • #14
                            WAP
                            Junior Member
                            • Apr 2010
                            • 44

                            I learned to reload on a progressive. It's not that complicated that you must learn "old school". I have only reloaded pistol though. I would not recommend learning to reload anything except straight wall ammo on a progressive. The rifle ammo can get complicated.

                            Comment

                            • #15
                              thevic
                              Senior Member
                              • Feb 2010
                              • 1910

                              I was thinking lee classic turret so i can run single and turrer...can i do .308 on it? And does the auto disk support .308?

                              I plan on making precision handload .308 on single.
                              Quick plinker loads of: .223, .40 on the turret.
                              Victor M.

                              Spartan Precision Rifles 07 FFL/SOT
                              Caldwell, ID

                              Comment

                              Working...
                              UA-8071174-1