Unconfigured Ad Widget

Collapse

Broken Lee decapper pin

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    GeoffLinder
    Senior Member
    • Jul 2009
    • 2425

    Originally posted by Bill Steele
    I broke my first Lee pin on a berdan primer case by mistake (didn't look close enough before starting the upstroke on the decap/size).

    When I bought a few replacement pins ($2/ea at Midway), when I replaced the pin I realized I could tighten the collet just tight enough so the pin would push up when encountering an obstruction but hold it strong enough to decap when everything is jake.

    I have the same pin in that die that I replaced (exactly once), but have run into quite a few Berdan cases along the way.
    Check this first, if your cases are mixed batch range pick or from unknown origin, you could very well have a Berdan style case in there. This will pretty much always break the de-capper pin on most dies. I have also seen crimped primers take out wimpy de-capping pins before too.

    Dillon dies have the strongest de-capping pins I have ever seen. Crushed a range rock one time rather than break the pin. Haven't came across a Berdan case with my Dillon dies yet, I inspect for this pretty carefully first and toss anything of unknown origin and pedigree.

    Comment

    • #17
      Bill Steele
      Calguns Addict
      • Sep 2010
      • 5028

      The good stuff.

      Originally posted by GeoffLinder
      Check this first, if your cases are mixed batch range pick or from unknown origin, you could very well have a Berdan style case in there. This will pretty much always break the de-capper pin on most dies. I have also seen crimped primers take out wimpy de-capping pins before too.

      Dillon dies have the strongest de-capping pins I have ever seen. Crushed a range rock one time rather than break the pin. Haven't came across a Berdan case with my Dillon dies yet, I inspect for this pretty carefully first and toss anything of unknown origin and pedigree.
      It was a Berdan primer case that broke my pin. I probably picked it up by mistake when getting my cases off the floor. Like posted earlier, I now set the collet that holds the Lee pin just tight enough that it will punch just about any primer out, but loose enough that it pushes the pin back when I hit a Berdan primer of some other obstruction. I actually watch the pin now when decapping/sizing, so I know when it moves up I have hit something. Works pretty well. I also bought a few extra pins (at $2/ea it is pretty cheap insurance). For sure, now that I have spares ready to go, I will never break another.
      When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

      Comment

      • #18
        rspar
        Senior Member
        • Jun 2009
        • 882

        I dug up the culprit that broke the pins and from what it says on the brass OJP 59 I think it's 1959 Austrian stuff I think at least. That wouldn't be berdan would it? I did stick a punch in it and tried to hammer out the primer but it didn't budge. Oh well I'll just be more careful what I pick up when doing my desert plinking. Thanks for the help.

        Comment

        • #19
          FLIGHT762
          Veteran Member
          • Mar 2009
          • 3072

          Originally posted by rspar
          I dug up the culprit that broke the pins and from what it says on the brass OJP 59 I think it's 1959 Austrian stuff I think at least. That wouldn't be berdan would it? I did stick a punch in it and tried to hammer out the primer but it didn't budge. Oh well I'll just be more careful what I pick up when doing my desert plinking. Thanks for the help.
          Yes, that is Austrian 30/06. Berdan primed. Get to know head stamps. Get a flashlight and shine it down into the case. You will be able to see if your cases are Boxer or Berdan (the Berdan primed cases will have two offset flash holes).

          After going through this you'll learn which cases are suitable for reloading.

          There are some foreign head stamp calibers that could have been both Berdan and Boxer at one time. Some of the Australian 7.62X51 (NATO) was Berdan primed and newer cases are Boxer. You need to look inside and save your decapping pin.

          Comment

          • #20
            bumpo628
            Senior Member
            • Nov 2009
            • 1142

            Originally posted by rspar
            I dug up the culprit that broke the pins and from what it says on the brass OJP 59 I think it's 1959 Austrian stuff I think at least. That wouldn't be berdan would it? I did stick a punch in it and tried to hammer out the primer but it didn't budge. Oh well I'll just be more careful what I pick up when doing my desert plinking. Thanks for the help.
            You have to look down the hole to see if there are two primer hole (not in the center) or one in the center. Berdan has two holes.
            Ronald Reagan once said that the most terrifying words in the English language are: "I'm from the government and I'm here to help".
            Download my alloy calculator here: http://castboolits.gunloads.com/showthread.php?t=105952

            Comment

            • #21
              ShootinMedic
              Senior Member
              • Sep 2009
              • 826

              I just deprimed / resized about 3000 9mm brass today with my Lee die and didn't have a single problem.
              Originally posted by Untamed1972
              ... the POV of courts and legislators needs to be....if an item can have a lawful purpose then you can't criminalize the item, you can only criminalize unlawful acts committed with that lawful item.

              Comment

              Working...
              UA-8071174-1