Unconfigured Ad Widget

Collapse

Reloading 44-40

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • quiet-wyatt
    CGN/CGSSA Contributor
    • Dec 2008
    • 934

    Reloading 44-40

    Have a question...

    I reload straight-wall cases - .45 Colt, .38/.357... I was thinking of getting into 44-40 but I keep hearing of reloading problems from the tapered 44-40 case...

    So - Are there extra steps to reloading 44-40 because of the tapered case? Are there precautions you take to prevent collapsed cases?

    Also - I was thinking of using some Brinell #12 .429 bullets and sizing them to .427 or .428 - depending on what I find after slugging the barrel of my *future* 44-40 revolver... What you you all think?

    Thanks...
    To do is to be. (Socrates)

    To be is to do. (Plato)

    Do be do be do. (Sinatra)
    sigpic
  • #2
    EmmaGoldman
    Member
    • Jan 2011
    • 369

    The lubrication step (is this what you mean by extra?) is because a simple ring sizing die can only be used on straight wall cases. This means that there is more surface contact between the case and the interior of the die, so lube helps prevent sticking.

    The other complaint people have about 44-40 is that the case walls are thinner than on many cases and this makes it easier to damage the case mouth if you sloppily bang in to the base of the die on your way in.

    Just remember to be a little more careful with the brass and remember to wipe off the lube before shooting and you'll be fine.
    Left, not "liberal", not what gets called "left" in American politics, Actually Left, like the government shouldn't be set up to favor certain groups, radically and fanatically left, like the ideas in the American Constitution (except that crap about 3/5ths of a person).

    Comment

    • #3
      quiet-wyatt
      CGN/CGSSA Contributor
      • Dec 2008
      • 934

      Originally posted by EmmaGoldman
      The lubrication step (is this what you mean by extra?) is because a simple ring sizing die can only be used on straight wall cases. This means that there is more surface contact between the case and the interior of the die, so lube helps prevent sticking.

      The other complaint people have about 44-40 is that the case walls are thinner than on many cases and this makes it easier to damage the case mouth if you sloppily bang in to the base of the die on your way in.

      Just remember to be a little more careful with the brass and remember to wipe off the lube before shooting and you'll be fine.
      Yes - That was the extra step I was looking for...
      Great info - Thanks!
      To do is to be. (Socrates)

      To be is to do. (Plato)

      Do be do be do. (Sinatra)
      sigpic

      Comment

      • #4
        EmmaGoldman
        Member
        • Jan 2011
        • 369

        Just treat them like little stubby rifle cartridges. That's what they really are.
        Left, not "liberal", not what gets called "left" in American politics, Actually Left, like the government shouldn't be set up to favor certain groups, radically and fanatically left, like the ideas in the American Constitution (except that crap about 3/5ths of a person).

        Comment

        • #5
          tteng
          Senior Member
          • Sep 2006
          • 1911

          I shot 44-40 out of my Uberti Henry. The case wall is so thin, I find it unnecessary to lube the brass for decap/sizing die. However, you do need a case mouth expanding die to bell out the mouth a bit. Also, bullet w/ bevelled bottom is easier to seat.

          Also, my Uberti rifle's bore is .429, and I use plated .429 bullets w/ great accuracy. If you check the Cimarron site, it also lists Uberti 44-40 revolver w/ .429 bore.

          Comment

          Working...
          UA-8071174-1