Unconfigured Ad Widget

Collapse

Maybe a simple question...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • NorCal Mtn Flyer
    Member
    • Aug 2010
    • 135

    Maybe a simple question...

    I'm still relatively new to reloading. All of the loading I have done to date was pre-primed, new brass. But all of that is now used brass!

    I have heard some comments that go both ways re: my question-

    Should I de-cap the brass prior to tumbling, or after?

    Thanks for your feedback!
  • #2
    Sheldon
    Senior Member
    • Oct 2005
    • 2149

    You can do it either way but most deprime after tumbling so the decapper will knock out any media that may get stuck in the flash hole. Otherwise you may/will have to look in each primer pocket and pick out any blockage.

    Comment

    • #3
      mstlaurent
      Senior Member
      • Mar 2007
      • 1408

      I decap, size, and trim before tumbling, then when I load I put a decapping die in station 1 to clear any media from the flash hole.
      I've never seen an American flag burned at a gun show.

      Comment

      • #4
        Chivas
        Member
        • Dec 2005
        • 334

        I tumble then de-cap and prime. If you de-cap and then tumble I STRONGLY suggest what "mstlaurent" does and use you de-capping die when priming. If you do not the flash holes will be filled with Media.

        Comment

        • #5
          Sheldon
          Senior Member
          • Oct 2005
          • 2149

          I should have clarified as far as how I do it. For pistol I tumble before running it thru the progressive press.

          For rifle I initially will tumble the cases before lubing and sizing, then I tumble again with a little mineral spirits in the corn cobb media to get the lube off, then i do the flash hole/primer pocket check for stuck media, then I trim the cases on the Giraud trimmer, and finally pack the ready to go cases in a container till needed.

          Comment

          • #6
            stphnman20
            Calguns Addict
            • Feb 2005
            • 6583

            I tumble brass before resize and decap. I don't want dirty brass going through my dies.

            Comment

            • #7
              Cowboy T
              Calguns Addict
              • Mar 2010
              • 5725

              Congrats on turning your new, pre-primed brass into used brass! This is a *good* thing!

              I tumble first, then run 'em through the decapper/resizer die, usually in the progressive press. The only reason to decap before cleaning is to clean the primer pocket, which I've found is not necessary for most shooting tasks. Maybe if you're doing precision bench-rest, that might help, but not for hunting or handgun tasks.
              "San Francisco Liberal With A Gun"
              F***ing with people's heads, one gun show at a time. Hallelujah!
              http://www.sanfranciscoliberalwithagun.com (reloading info w/ videos)
              http://www.liberalsguncorner.com (podcast)
              http://www.youtube.com/sfliberal (YouTube channel)
              ----------------------------------------------------
              To be a true Liberal, you must be 100% pro-Second Amendment. Anything less is inconsistent with liberalism.

              Comment

              • #8
                killshot44
                Veteran Member
                • Nov 2009
                • 4072

                I've used three different brands of crushed walnut, I found only the "Zilla" brand at PetCo to NOT stick in small primer pockets (.223 and 6mm).

                I tumble, decap, size, trim, tumble, prime and load.

                Comment

                • #9
                  30Cal
                  Senior Member
                  • Jan 2006
                  • 1487

                  I use the tumble to keep the dies from getting scratched, so I tumble first.

                  Comment

                  • #10
                    Divernhunter
                    Calguns Addict
                    • May 2010
                    • 8753

                    Tumble first. Never had dirty primer pockets become a problem.
                    A 30cal will reach out and touch them. A 50cal will kick their butt.
                    NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
                    SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

                    Comment

                    • #11
                      Bigtwin
                      Veteran Member
                      • May 2010
                      • 2639

                      I prefer to tumble the dirty brass before I put them through my dies!
                      NRA MEMBER

                      Comment

                      • #12
                        NorCal Mtn Flyer
                        Member
                        • Aug 2010
                        • 135

                        Thanks for the feedback...

                        It seems as though either way will work, but maybe fewer steps by tumbling first, as described by most of the responses.

                        Comment

                        • #13
                          RaymondMillbrae
                          Veteran Member
                          • Jun 2009
                          • 2659

                          Hey, shooter,

                          Check out the reloading tutorial below my signature. (Reloading. 223 video).

                          I don't know what you are reloading (rifle or pistol), but if you are considering rifle, the videos will help answer many of your questions.

                          In Christ: Raymond
                          Some of my tutorials:

                          RELOADING .223 VIDEO
                          HOME MADE RECOIL SPRING TESTER
                          SHORTENING THE LOP ON AN FN SLP SHOTGUN
                          INSTALLING SIGHTS ONTO A REMMY 870P
                          HORNADY 366 AUTO - INTRO OF PRESS & SLUG COMPONENTS (Part 1)
                          HORNADY 366 AUTO - PROGRESSIVE RELOADING OF LYMAN SABOT SLUGS (Part 2)

                          Comment

                          Working...
                          UA-8071174-1