Unconfigured Ad Widget

Collapse

primer size chart anywhere?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Falstaff
    Senior Member
    • Mar 2010
    • 2317

    primer size chart anywhere?

    I want to order some primers for all the ammo I shoot (even though i don't have reloading equipment for all of them yet). I'm not 100% sure about primer sizes for the following calbers:

    9mm= small pistol

    40S&w= small pistol or large pistol?

    .45ACP large pistol

    38special small pistol??
    .357 magnum small pistol or magnum pistol?

    45LC/454 casull large pistol or magnum pistol??

    .223 small rifle

    .308 large rifle?

    30-06 large rifle?
    45-70?
  • #2
    jwest
    Veteran Member
    • Dec 2008
    • 3958

    sigpic
    "They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety." --- Benjamin Franklin
    Freedom isn't free. Read the Declaration of Independence everyday - it'll keep the New World Order away.
    Quote: Army: "Your ignorant liberal puke rhetoric is tiresome."
    We live in a society of extreme behavior with no electronic self control.

    Comment

    • #3
      Falstaff
      Senior Member
      • Mar 2010
      • 2317

      I've seen that link, but it doesnt say specifically what calibers it just says for "most small calber" or something like that.

      Comment

      • #4
        jwest
        Veteran Member
        • Dec 2008
        • 3958

        Falstaff,

        Do you have a reloading manual?

        Regards,
        jwest
        sigpic
        "They who can give up essential liberty to obtain a little temporary safety, deserve neither liberty nor safety." --- Benjamin Franklin
        Freedom isn't free. Read the Declaration of Independence everyday - it'll keep the New World Order away.
        Quote: Army: "Your ignorant liberal puke rhetoric is tiresome."
        We live in a society of extreme behavior with no electronic self control.

        Comment

        • #5
          freonr22
          I need a LIFE!!
          • Dec 2008
          • 12955

          randall had a super detailed primer chart in the past, not what you were asking, but showed this brand was .0015 larger than that brand etc. It would be really nice to compile that type of detailed info like a sticky
          sigpic
          Originally posted by dantodd
          We will win. We are right. We will never stop fighting.
          Originally posted by bwiese
          They don't believe it's possible, but then Alison didn't believe there'd be 350K - 400K OLLs in CA either.
          Originally posted by louisianagirl
          Our fate is ours alone to decide as long as we remain armed heavily enough to dictate it.

          Comment

          • #6
            Falstaff
            Senior Member
            • Mar 2010
            • 2317

            I do have a manual,(somewhere it's 20+ years old) I used to reload .45acp/9mm/.223 on a LEE 1,000 20 years ago. All I'm asking is what is the dividing line between small pistol and large pistol and magnum pistol. same thing with small rifle/large rifle/magnum rifle.

            I reloaded thousands of rounds of .45ACp with absolutely no problems many years ago. So I don't need safety tips, or load data at this time, just wondering what the definitions of small and large caliber is.

            The calibers I listed in the original post with question marks after them are the ones I'm not 100% sure on cuz I've never reloded them before.
            Last edited by Falstaff; 01-07-2011, 1:51 AM.

            Comment

            • #7
              freonr22
              I need a LIFE!!
              • Dec 2008
              • 12955

              sigpic
              Originally posted by dantodd
              We will win. We are right. We will never stop fighting.
              Originally posted by bwiese
              They don't believe it's possible, but then Alison didn't believe there'd be 350K - 400K OLLs in CA either.
              Originally posted by louisianagirl
              Our fate is ours alone to decide as long as we remain armed heavily enough to dictate it.

              Comment

              • #8
                Munk
                Senior Member
                • Jun 2010
                • 2124

                You'll find a little mixing on the mid cal's. .45acp has been spotted with both large and small... That's close to the dividing line.

                There's only 2 sizes. Large and small. When you order, look at your old brass, figure out which you've got.

                After that is' Rifle or Pistol (it matters) but it's still Large and small.

                Then there's to Magnum... or NOT to Magnum... that is the question. The only magnums you might need are for the .357 and maybe the .454.


                If you have every single calibur listed above, you'll need to buy: Large pistol, Large pistol magnum, Small pistol, Large rifle, Small rifle. .30-06 doesn't NEED magnum, but it really won't matter much... I know very little about loading 45-70.

                I currently run my .30-06 on regular large rifle, a .44 mag on regular large pistol, I don't use magnums in any of my loads and they all work just fine... i just realized, I have no small rifles lol.
                Originally posted by greasemonkey
                1911's instill fairy dust in the bullets, making them more deadly.

                Comment

                • #9
                  Falstaff
                  Senior Member
                  • Mar 2010
                  • 2317

                  Originally posted by Munk
                  You'll find a little mixing on the mid cal's. .45acp has been spotted with both large and small... That's close to the dividing line.

                  There's only 2 sizes. Large and small. When you order, look at your old brass, figure out which you've got.

                  After that is' Rifle or Pistol (it matters) but it's still Large and small.

                  Then there's to Magnum... or NOT to Magnum... that is the question. The only magnums you might need are for the .357 and maybe the .454.


                  If you have every single calibur listed above, you'll need to buy: Large pistol, Large pistol magnum, Small pistol, Large rifle, Small rifle. .30-06 doesn't NEED magnum, but it really won't matter much... I know very little about loading 45-70.

                  I currently run my .30-06 on regular large rifle, a .44 mag on regular large pistol, I don't use magnums in any of my loads and they all work just fine... i just realized, I have no small rifles lol.
                  Thank you very much for the polite insightful reply. Now i understand better that it's not as cut dried as i assumed, that's why i couldnt find a chart that says: 30.06 takes THIS:____ 30-30 takes THIS____ 45ACP takes THIS_____etc etc.

                  I'll just buy'em all!

                  Comment

                  • #10
                    Cowboy T
                    Calguns Addict
                    • Mar 2010
                    • 5725

                    Also, while .357 Magnum normally takes small pistol primers, I actually have about 20 cases of REM-UMC headstamped .357M brass that takes *large* pistol.

                    Also, you have the case of .40 S&W taking small pistol primers, but its parent cartridge, the 10mm Auto (same caliber), takes large pistol primers. This was because of the design of the guns for .40 S&W; apparently the large pistol primers were getting struck during extraction and chambering from the magazine.

                    Also, while .45 ACP uses (mostly) large pistol primers, .45 GAP uses small pistol.

                    Finally, .45 Colt takes large pistol primers...but .454 Casull takes...SMALL *RIFLE* primers! Yup, small *rifle*.

                    So, unfortunately, there really is no clear-cut "dividing line" at caliber. It really is cartridge-specific, and it can vary even within the same family.
                    "San Francisco Liberal With A Gun"
                    F***ing with people's heads, one gun show at a time. Hallelujah!
                    http://www.sanfranciscoliberalwithagun.com (reloading info w/ videos)
                    http://www.liberalsguncorner.com (podcast)
                    http://www.youtube.com/sfliberal (YouTube channel)
                    ----------------------------------------------------
                    To be a true Liberal, you must be 100% pro-Second Amendment. Anything less is inconsistent with liberalism.

                    Comment

                    • #11
                      Divernhunter
                      Calguns Addict
                      • May 2010
                      • 8753

                      The 45-70 uses large rifle as does the 30-06. The 454 uses small rifle mag but some early brass used large pistol mag. As far as mag vrs reg primers I use mag for all my reloading and never had trouble. I do have some reg primers I got cheap but usually use mag primers for everything from 204ruger to 338win mag and 45-70. I also use mag primers in 9mm to 454 casull.
                      A 30cal will reach out and touch them. A 50cal will kick their butt.
                      NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
                      SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

                      Comment

                      • #12
                        mikehaas
                        Senior Member
                        • Mar 2006
                        • 1237

                        FYI, http://AmmoGuide.com/ displays the appropriate primer in its Visual Comparison Tool...



                        Also lists the primer diameter on the cartridge's detailed info page, in the "SPECIFICATIONS" table on the right...



                        When you get into older European chamberings, there are more than 2 sizes.
                        sigpic
                        NRA Members' Councils of California 2008 Volunteer of the Year
                        Developer, Interactive version of the CA AW ID Flowchart
                        Owner/author, http://AmmoGuide.com/
                        Webmaster, http://calnra.com/

                        Comment

                        • #13
                          uscbigdawg
                          Senior Member
                          • Nov 2007
                          • 1869

                          Go off a reloading manual (I like Sierra's a lot) and you'll be squared away. There are general rules and there are those of us that make life simple and just load small rifle in just about everything (9mm, 38 Super, 40, 223, etc.).

                          Rich
                          "Speed is a tactic!" - R.W.

                          "Pressure is what you feel when you don't know what you're doing." - Chuck Knox

                          "The callus on my finger is from my trigger, not the keyboard!" - Rob Leatham

                          Comment

                          • #14
                            pisarski
                            Senior Member
                            • Aug 2009
                            • 740

                            40 sw is sp , 38 spe sp, 357 mag is sp or spm by your load, 45 lc lp, 308 lr, 30.06 lr, 45/70 lr
                            hopes that helps Ray

                            Comment

                            • #15
                              bumpo628
                              Senior Member
                              • Nov 2009
                              • 1142

                              I found a 3 page primer size / bullet diameter chart on Grafs.com.
                              This is going up on the garage wall...

                              Cheddite 209 primers give shotshell reloaders reliable, consistent ignition in every hull. Stock up with a full case of 5,000 primers from Graf & Sons.


                              I took the liberty of hosting the files for you guys here:
                              Page 1 - http://www.pdfhost.net/index.php?Act...8573fe4d49e068
                              Page 2 - http://www.pdfhost.net/index.php?Act...6fbcff8a61868e
                              Page 3 - http://www.pdfhost.net/index.php?Act...d7a25a7a3c57b4
                              Ronald Reagan once said that the most terrifying words in the English language are: "I'm from the government and I'm here to help".
                              Download my alloy calculator here: http://castboolits.gunloads.com/showthread.php?t=105952

                              Comment

                              Working...
                              UA-8071174-1