Unconfigured Ad Widget

Collapse

Hand priming problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • eridepilot
    Junior Member
    • Aug 2009
    • 96

    Hand priming problem

    Hi everyone,
    I was priming .223rem with the RCBS hand priming tool and had a primer only seat about a quarter of the way. What is the best way to ether remove the primer or try to finish seating the primer?

    Thanks
  • #2
    Sheldon
    Senior Member
    • Oct 2005
    • 2149

    If you can get it out of the priming tool with the primer hanging that far out, you can push the primer back out with the sizing die/decapper. If the partial primed case cannot be removed from the tool then I would wear some ear plugs, aim the case opening in a safe direction away from your face and then try seating it enough to clear the tool. Is the problem case a military crimped primer pocketed one?

    Comment

    • #3
      XDRoX
      Veteran Member
      • Mar 2009
      • 4420

      With enough force you can crush the primer into the case. You would be wise to wear eyes and ears as already stated.

      When we were setting our swager the other night, we would adjust it, and test the case by priming it. It took many tries to get the swager adjusted perfect. You wouldn't believe the amount of pressure that I put on my hand primer. Not one primer went off even though some were crushed beyond recognition.
      Chris
      <----Rimfire Addict


      Originally posted by Oceanbob
      Get a DILLON...

      Comment

      • #4
        eridepilot
        Junior Member
        • Aug 2009
        • 96

        I was able to remove the case from the tool. I will try to use the sizer/decaping die. The case is not military crimped. Can the primer be used again or should it be disposed of?

        Comment

        • #5
          XDRoX
          Veteran Member
          • Mar 2009
          • 4420

          Originally posted by eridepilot
          I was able to remove the case from the tool. I will try to use the sizer/decaping die. The case is not military crimped. Can the primer be used again or should it be disposed of?
          If you got it out of the hand primer, it'll pop out easy with the die. It's up to you if you want to reuse it. I reuse them all the time and have never had a problem. Some people will say because they're so cheap, why chance it.

          After you seat and re-seat a few times though, the primer will become smaller and will not stay in a case.
          Chris
          <----Rimfire Addict


          Originally posted by Oceanbob
          Get a DILLON...

          Comment

          • #6
            SixPointEight
            Veteran Member
            • May 2009
            • 3788

            Originally posted by XDRoX
            With enough force you can crush the primer into the case. You would be wise to wear eyes and ears as already stated.

            When we were setting our swager the other night, we would adjust it, and test the case by priming it. It took many tries to get the swager adjusted perfect. You wouldn't believe the amount of pressure that I put on my hand primer. Not one primer went off even though some were crushed beyond recognition.
            same here. I had one where I split the cup. Part of it flattened against the rim, the part of the primer that did seat was completely flattened too. Didn't go off either

            Comment

            • #7
              EL_NinO619
              Senior Member
              • Sep 2010
              • 1519

              Originally posted by XDRoX
              With enough force you can crush the primer into the case. You would be wise to wear eyes and ears as already stated.

              When we were setting our swager the other night, we would adjust it, and test the case by priming it. It took many tries to get the swager adjusted perfect. You wouldn't believe the amount of pressure that I put on my hand primer. Not one primer went off even though some were crushed beyond recognition.
              I was there, and I'm completely amazed they did not go off. Now they where CCI which tend to be on the tougher side. I would not try that with a Federal primer. But always wear proper protection.
              se carga el diablo de la pistola...
              .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
              On 2 Hornady LnL AP & Dillon Super 1050

              Comment

              • #8
                22popnsplat
                Senior Member
                • May 2008
                • 1042

                I have never had primer go off using a hand priming tool (Lee is what i usually use ) , I think using gradually increasing pressure it would be rare for a primer to be set off . takes more of a sharp impact , I only heard of primers being set off while being installed by a reloading press and I think the operator may be trying to go to fast .
                Last edited by 22popnsplat; 10-28-2010, 3:37 PM.

                Comment

                • #9
                  bohoki
                  I need a LIFE!!
                  • Jan 2006
                  • 20826

                  i've pushed out a primer to use in another case it worked fine

                  but i kind of have a feel for how a primer seats and can tell when one goes in too loose i have a bent paperclip handy if i feel one go is too easy and try to push it out with it and if i cant i figure its in good enough

                  if you push out one that only went half way save it for another case (preferably a case that never had a crimp) then give that pocket a reaming

                  Comment

                  • #10
                    Boots
                    Senior Member
                    • Aug 2008
                    • 549

                    Correct me if I'm wrong... but isn't the anvil not completely in the primer cup until it is fully seated in the brass/shell? Thus they are less likely to be set off (by a sharp impact) than when fully installed? I've noticed on the Remington SR primers that you can see the ends of the anvil just above the lip of the cup.
                    I think that... along with being inserted with a flat base of a priming tool is what makes it less likely for them to go off... and when they do, it's because they are being crushed in a very short moment.

                    When I first started loading, I was using the priming feature of my press and didn't realize that one of the primers wasn't sitting flat in the holder and it got crushed sideways into the primer pocket without any mishap. To be safe, I soaked it in WD40 for a day before I "de-primed" that sucker.
                    Eat what you kill... unless it's a zombie.

                    Comment

                    • #11
                      eridepilot
                      Junior Member
                      • Aug 2009
                      • 96

                      Was able to remove primer and use it again. Thanks for all the help.

                      Comment

                      Working...
                      UA-8071174-1