Unconfigured Ad Widget

Collapse

Things I learned first time reloading...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • EROCO
    Junior Member
    • Aug 2010
    • 79

    Things I learned first time reloading...

    I just finished my first batch (50 rounds) of 308 using the ff:

    New Win brass
    Federal Primer / Match
    RE-15 / 42.5 gr
    Sierra 168 Matchking

    Lee Press (50th kit)
    Redding dies
    Forster trimmer
    HF Tumbler
    RCBS Primer Flash uniformer tool

    1. Never trust the Lee Powder measure to give you a consistent reading.
    I measured every charge and just used the powder measure to get it close then the trickler to get it exact.

    2. Never trust the dials on the Lee scale, I just used the Lyman scale weight check to calibrate my weight/scale.

    3. I blistered my hand using the flash hole uniformer tool, I will use a drill next time, lol.

    4. Measure three times and press once to seat the bullet in. Repeat until the COAL measures 2.8000, just a little at a time..

    5. It's nice to have another Calgunner as your next door neighbor to get advice and tips from.

    I read just about every thread here on reloading and learned a lot from that and went at it head first..

    Thanks everyone.

    My setup:


    Calibrate scale:


    My babies:


    Range next week to test them out..
  • #2
    Boots
    Senior Member
    • Aug 2008
    • 549

    Hope you like those Sierra's
    The #2200's are what I load and so far so good!
    Eat what you kill... unless it's a zombie.

    Comment

    • #3
      freonr22
      I need a LIFE!!
      • Dec 2008
      • 12955

      with all respect, I appreciate your setup. I had no luck w/ the lee scale. Would you conside,r if it suits you, to try an RCBS or other? I am a newbie too, and threw mine away after 30 rounds.
      sigpic
      Originally posted by dantodd
      We will win. We are right. We will never stop fighting.
      Originally posted by bwiese
      They don't believe it's possible, but then Alison didn't believe there'd be 350K - 400K OLLs in CA either.
      Originally posted by louisianagirl
      Our fate is ours alone to decide as long as we remain armed heavily enough to dictate it.

      Comment

      • #4
        bohoki
        I need a LIFE!!
        • Jan 2006
        • 20826

        i loaded up 100 .308 fmj using win 748 and the lee perfect powder measure was spot on for me its not as good with varget though

        Comment

        • #5
          EROCO
          Junior Member
          • Aug 2010
          • 79

          Originally posted by freonr22
          with all respect, I appreciate your setup. I had no luck w/ the lee scale. Would you conside,r if it suits you, to try an RCBS or other? I am a newbie too, and threw mine away after 30 rounds.
          I already have an elec scale on the way from Midway..

          Comment

          • #6
            EROCO
            Junior Member
            • Aug 2010
            • 79

            Originally posted by bohoki
            i loaded up 100 .308 fmj using win 748 and the lee perfect powder measure was spot on for me its not as good with varget though
            Maybe the RE-15 powder did'nt like the Lee Powder measure (big granules), there were times when I do a load on the funnel that I can feel some powder wedged in the internal mechanism and it felt like grinding coffee, lol..

            Comment

            • #7
              Cowboy T
              Calguns Addict
              • Mar 2010
              • 5725

              The Lee disk-based powder measures do seem to do much better with the smaller-granuled powders. Bullseye, Titegroup, 2400, H322, and Clays all meter really well through it. Others report that Unique doesn't do so well in the smaller cavities.
              "San Francisco Liberal With A Gun"
              F***ing with people's heads, one gun show at a time. Hallelujah!
              http://www.sanfranciscoliberalwithagun.com (reloading info w/ videos)
              http://www.liberalsguncorner.com (podcast)
              http://www.youtube.com/sfliberal (YouTube channel)
              ----------------------------------------------------
              To be a true Liberal, you must be 100% pro-Second Amendment. Anything less is inconsistent with liberalism.

              Comment

              • #8
                knucklehead0202
                Veteran Member
                • Aug 2008
                • 4087

                my lee measure does fine with BL(C)-2 but it's spherical and flows real easy.

                Comment

                • #9
                  bootcamp
                  Senior Member
                  • Mar 2006
                  • 1019

                  Sledge hammer that POS Lee scale and buy yourself a good rcbs 5-0-5 scale. I don't even trust the electric scales.
                  Originally posted by ar15barrels
                  Lube helps whenever you are trying to get something into a tight hole.

                  Comment

                  • #10
                    freonr22
                    I need a LIFE!!
                    • Dec 2008
                    • 12955

                    Originally posted by bootcamp
                    Sledge hammer that POS Lee scale and buy yourself a good rcbs 5-0-5 scale. I don't even trust the electric scales.

                    Thank you! that is what i meant, but did not want to be that blunt.

                    its really not directed @ the op, as he is correcting that issue, but for anyone read noobs, reading this thread. their presses are fine, their dies are fine, but their scale stinks
                    sigpic
                    Originally posted by dantodd
                    We will win. We are right. We will never stop fighting.
                    Originally posted by bwiese
                    They don't believe it's possible, but then Alison didn't believe there'd be 350K - 400K OLLs in CA either.
                    Originally posted by louisianagirl
                    Our fate is ours alone to decide as long as we remain armed heavily enough to dictate it.

                    Comment

                    • #11
                      brianinca
                      Member
                      • May 2010
                      • 359

                      >>
                      I blistered my hand using the flash hole uniformer tool, I will use a drill next time, lol.
                      >>

                      You're overdoing it, I do 250 pieces of HXP at a time with a Lyman. All you want is any residue from drilling knocked off. Virgin Winchester 308 brass has 10% with some resistance, the surplus Greek 3006 HXP (once fired) is about 1%, it's probably a waste of time but I do it anyway.

                      Also, if you're measuring COAL you're going to see a lot of variation with any of the HPBT type bullets. You're better off picking an index off the ogive with a cartridge length gauge and going off that.

                      If you ordered a ChargeMaster 1500, you're going to LOVE it. I'm sure the other electrified charge throwers are fine, too, but that was one of the best tools I ever bought.

                      Regards,
                      Brian in CA

                      Comment

                      • #12
                        knucklehead0202
                        Veteran Member
                        • Aug 2008
                        • 4087

                        i bought a Lyman 1200 dps3, one of the "other" electric throwers/scales, but have yet to try it out. all accounts i've heard are good though. maybe i'll get a chance to try it this weekend....

                        Comment

                        • #13
                          EL_NinO619
                          Senior Member
                          • Sep 2010
                          • 1519

                          Give the powder thrower some time, they all need to be broken in with a few pounds ran through them.
                          se carga el diablo de la pistola...
                          .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
                          On 2 Hornady LnL AP & Dillon Super 1050

                          Comment

                          • #14
                            EROCO
                            Junior Member
                            • Aug 2010
                            • 79

                            Originally posted by EL_NinO619
                            Give the powder thrower some time, they all need to be broken in with a few pounds ran through them.
                            I actually ran some Varget in it last night and I was consistently within half a grain each time which is better than when I ran the RE15 with it.

                            It is what it is, I just basically trust it enough that I get it close using that and use the scale with a trickler to finish the load.

                            Comment

                            • #15
                              EL_NinO619
                              Senior Member
                              • Sep 2010
                              • 1519

                              A half a grain is pretty extreme. Do you mean .01-.02. I have got mine to throw pretty consistent charges. Accurate enough that +- 0.01 grain is good enough. Unless i am loading for complete accuracy, then i use my trickler to drop a few granules. But most powder throwers tend to vary in weight by charges when using large stick powders like RE-15.
                              se carga el diablo de la pistola...
                              .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
                              On 2 Hornady LnL AP & Dillon Super 1050

                              Comment

                              Working...
                              UA-8071174-1