Unconfigured Ad Widget

Collapse

How much does crimp effect pressure?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • diginit
    Veteran Member
    • Feb 2008
    • 3250

    How much does crimp effect pressure?

    I've been loading for 5.56. Worked up to 26.5g of Win 748 under a 55g FMJ with a light crimp from the seating die and have fired a few thousand with no overpressure issues other than an extractor mark once in a while. But I also noticed that the base on 3 out 100 of twice fired rnds are very tight in my shellholder. Is this a sign of overpressure that I don't know about?

    I just got a factory crimp die and I prefer a crimp as I shoot a Bushy heavy barrel AR and a Keltec SU-16. Both semi autos. The max from Lee and Win for a 55g is 26.2g of 748 for 223. 26.2 gives me an average of 2900 fps. from a 16" and 18" barrel. I haven't chrono'ed 26.5. But I estimate 3050. Still slow for a 5.56 but accurate. I get alot of different data from other books. Some maxed at 27.2. Do some books list SAMMI specs and others list NATO or what??? Anyways...
    Will a tighter crimp increase the chamber pressure? Should I work up a new load if I increase the crimp to medium or max? I'm curious how this change would effect the load. What is the max you guys worked up to in a 16" 1/9 twist carbine with 748? TIA
    Last edited by diginit; 09-15-2010, 9:04 PM.
  • #2
    Boots
    Senior Member
    • Aug 2008
    • 549

    I would be careful, as yes.. you can get in a dangerous situation.
    I personally don't crimp for my AR's... not unless the bullet I'm seating has a cannelure.
    Eat what you kill... unless it's a zombie.

    Comment

    • #3
      diginit
      Veteran Member
      • Feb 2008
      • 3250

      Win. 55g fmj's have a cannelure. And according to the Lee factory die instructions. If a bullet does not have a cannelure, The die will make one. I thought that was strange, But it is in black and white from Lee. Although it goes against what I have read about crimping.
      I guess I should add that my OAL is 2.200 (Win. Specs) which puts the entire crimp dead center of the cannelure. Cases are exactly 1.750.
      Last edited by diginit; 09-15-2010, 9:31 PM.

      Comment

      • #4
        Boots
        Senior Member
        • Aug 2008
        • 549

        with a cannelure... you're GTG. But for how much crimp is too much... I, like you, is interested in the answer.
        Your OAL is dependent on your bullet weight and cannelure.. and since it's a 55 GR, it understandable for the 2.200.. but you def got a jump going there. I got mine to the max (of the magazine) at 2.26 where I measured my AR chambers at 2.384 and 2.375, respectively.
        Eat what you kill... unless it's a zombie.

        Comment

        • #5
          diginit
          Veteran Member
          • Feb 2008
          • 3250

          I noticed that also. My last workup was sierra 55's to 1.250 neck tension only.
          But I have seen very little factory or military 5.56 ammo without a crimp. And I have never had a setback with them. Even with a bad mag.

          Here's a few loads I've worked up so far...
          Winchester 55gr FMJ
          26.5gr Win 748
          OAL 2260
          CCI #41 primers

          Hornady .224 VMAX 55gr
          26.2 Win 748
          OAL 2260
          CCI 400 Primers and Wolf Primers
          Flat at 27gr

          Speer 55gr .224 TNT HPBT
          26.5gr Win 748
          OAL 2250
          CCI 400 Primers

          Montana Gold 55 gr FMJBT
          26.4gr Win 748
          OAL 2220 - Slight Crimp
          CCI 400 Primers

          Hornady .224 55gr SP
          26.2 gr Win 748
          OAL 2220
          CCI Primers

          Midway 55gr FMJBT
          26.3 and 26.5 gr win 748
          OAL 2.220
          CCI #400 primers

          Midway 55Gr FMJBT
          26.0 gr Varget
          OAL 2.220
          CCI #400 primers

          Win .224 FMJBT
          26.5gr Win 748
          OAL 2.200 light crimp
          CCI #400 primers
          Last edited by diginit; 09-15-2010, 10:11 PM.

          Comment

          • #6
            Boots
            Senior Member
            • Aug 2008
            • 549

            From what I understand... military specs require crimping because of the violent nature of a weapon firing in selective fire. (full auto) Same reason why I'm sure they crimp primers. Just don't want anything to come loose.

            For civilian (semi-auto) use, it's not necessary. Again, when it comes to non-cannelured bullets.
            Eat what you kill... unless it's a zombie.

            Comment

            • #7
              diginit
              Veteran Member
              • Feb 2008
              • 3250

              Guess you don't bumpfire much....Like I do....

              Comment

              • #8
                mnguyen84
                Senior Member
                • May 2010
                • 1132

                i always thought crimping is supposed to help prevent the bullet from getting loose and falling out of its intended seat position. it's recommended for ammo that is to be used for hunting. I dont think it's significant enough to have that big of an impact on the pressure produced during combustion. crimped or not, i think if the bullet is seated correctly, the biggest factors of pressure are probably compression and burn-rate.

                Comment

                • #9
                  diginit
                  Veteran Member
                  • Feb 2008
                  • 3250

                  Crimping also protects against setback in a semi or full auto. A bullet pushed back into the case during feeding will dramatically increase pressure if fired. It seems to me that a bullet held in position longer by a tight crimp during the burn may do this also. But I'm just guessing. That's why I asked.

                  Comment

                  • #10
                    mnguyen84
                    Senior Member
                    • May 2010
                    • 1132

                    i'm also guessing, and i'm sure it does influence pressure to some degree. but if the crimp really kept it in place that much longer to be a major impact of pressure...then i would suspect there would different listing of data for crimped vs non-crimped loads.

                    Comment

                    • #11
                      killshot44
                      Veteran Member
                      • Nov 2009
                      • 4072

                      I've run 55gr over 26.5gr of Varget with no problems, haven't used WIN748.

                      Unless you're really torqueing down the crimp die, that "shouldn't" contribute to an overpressure in my short experience. FWIW I also never crimp for my semi-autos, proper neck-tension does the job.

                      As far as velocities go, unless you NEED fragmentation there's no reason to push 'em so fast. I get much better accuracy in the 2,650 to 2,800 range. Additionally, factory and NATO ammos are made using proprietary blends of powder not sold commercially.

                      Comment

                      • #12
                        ireload
                        Veteran Member
                        • Aug 2009
                        • 2589

                        Yes it would. By how much can only be measured by using a pressure transducer.

                        Now with applying more crimp you can also run into a problem of buckling the brass.

                        Comment

                        • #13
                          Nodda Duma
                          • Nov 2007
                          • 3455

                          Just work up a load with a fixed amount of crimp and you'll be fine. Change a variable, work up the load.
                          Looking for photos for your wall?
                          Help feed my children by clicking here.

                          Comment

                          • #14
                            22popnsplat
                            Senior Member
                            • May 2008
                            • 1042

                            Originally posted by Nodda Duma
                            Just work up a load with a fixed amount of crimp and you'll be fine. Change a variable, work up the load.
                            theres the right answer .

                            Comment

                            Working...
                            UA-8071174-1