Unconfigured Ad Widget

Collapse

Looking to start reloading. have a question.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Noah3683
    Senior Member
    • Aug 2009
    • 2256

    Looking to start reloading. have a question.

    is this lee kit pretty good to start?




    Or should I just spend a little more for something more like this rcbs?



    Or should I piece a kit together from various mfg's? The reason I ask is I'm finding mixed people that say don't waste your time, and others that say the lee is the best they've ever had. I'm mainly looking to reload .223 and maybe 9mm
    Originally posted by Neil McCauley
    Are you actually suppost to "taste" wood?
    Originally posted by Neil McCauley
    Just wish I knew what wood in your meat is suppost to taste like.
  • #2
    jwc
    Member
    • Jan 2008
    • 453

    If you want a turret press, the Lee Classic Turret Press is a better value (sturdier, better powder thrower) and does not cost much more.



    I have owned a Lee Classic Turret Press, a Lee Load Master and a Lee Classic Single Stage press. I like the single stage press best. It is very accurate, forces you to concentrate on each step and produces very consistent rounds - about 100 per hour.
    Last edited by jwc; 05-06-2010, 8:16 PM.

    Comment

    • #3
      Noah3683
      Senior Member
      • Aug 2009
      • 2256

      I'm not sure if I want/need a turret press, That was just the kit I was referred to by a few people. I have also been told to get the lee breech lock kit then upgrade the press later.
      Originally posted by Neil McCauley
      Are you actually suppost to "taste" wood?
      Originally posted by Neil McCauley
      Just wish I knew what wood in your meat is suppost to taste like.

      Comment

      • #4
        jwc
        Member
        • Jan 2008
        • 453

        Originally posted by Noah3683
        I'm not sure if I want/need a turret press, That was just the kit I was referred to by a few people. I have also been told to get the lee breech lock kit then upgrade the press later.
        The Breech Lock kit will certainly get the job done, but the scale is a bit weak. If you can see the presses in person and compare them against other manufacturers offerings that will help.

        Comment

        • #5
          XDRoX
          Veteran Member
          • Mar 2009
          • 4420

          I would not get that Lee press that you posted.
          I would get one of these:
          50 rounds an hour:

          250 rounds an hour:

          500 rounds an hour:
          Shop Dillon Precision for premium reloading presses, dies, conversion kits, parts, accessories and reloading equipment. Trusted by reloaders for decades.

          I would argue with anyone that these are three of the best presses out there. Each the best in their class. Depending on how much you want to spend and how fast you need to load, one of these three will surely meet your expectations.
          Chris
          <----Rimfire Addict


          Originally posted by Oceanbob
          Get a DILLON...

          Comment

          • #6
            Noah3683
            Senior Member
            • Aug 2009
            • 2256

            Originally posted by XDRoX
            I would not get that Lee press that you posted.
            I would get one of these:
            50 rounds an hour:

            250 rounds an hour:

            500 rounds an hour:
            Shop Dillon Precision for premium reloading presses, dies, conversion kits, parts, accessories and reloading equipment. Trusted by reloaders for decades.

            I would argue with anyone that these are three of the best presses out there. Each the best in their class. Depending on how much you want to spend and how fast you need to load, one of these three will surely meet your expectations.
            I guess that about sums it up. I'll hold off for the rcbs
            Originally posted by Neil McCauley
            Are you actually suppost to "taste" wood?
            Originally posted by Neil McCauley
            Just wish I knew what wood in your meat is suppost to taste like.

            Comment

            • #7
              XDRoX
              Veteran Member
              • Mar 2009
              • 4420

              You might be able to buy the parts separately and get started for a little less money if you are willing to forgo a few of the things that the RCBS kit comes with.

              That Lee Classic Turret form Kempf's is a screaming deal. I think I'd be more inclined to start with that one than the RCBS kit.

              If you want a single stage press you can almost go with any brand. Lee probably makes a pretty nice one as well. I have that RCBS single stage press kit and it's nice. I have a Lyman single stage press as well, and for the price difference, I think it's just as good as the RCBS.
              Chris
              <----Rimfire Addict


              Originally posted by Oceanbob
              Get a DILLON...

              Comment

              • #8
                XDRoX
                Veteran Member
                • Mar 2009
                • 4420

                If you really want to reload for as little as possible I would go this route.
                Lee Classic Cast Press = $85


                FA caliper = $22


                Dillon scale = $55


                For $162 you'd be ready roll.

                Actually, this list really makes Kempf's $178 deal even look better.
                Get that
                Chris
                <----Rimfire Addict


                Originally posted by Oceanbob
                Get a DILLON...

                Comment

                • #9
                  Milsurp Collector
                  Calguns Addict
                  CGN Contributor
                  • Jan 2009
                  • 5884

                  All of the major manufacturers make good equipment, they wouldn't stay in business if they didn't. When choosing equipment I find it very helpful to read the customer reviews at MidwayUSA.com (like reading customer reviews at Amazon.com and Newegg.com). Read the customer reviews of that Lee kit http://www.midwayusa.com/viewProduct...tNumber=622290

                  Here are some reviews of the Lee turret press by customers who already owned other brands

                  Stephen Yaw of north fort myers, fl
                  Date posted: 3/28/2006
                  Dang. This is the best press I have used yet. Caliber change-overs occur in seconds and need NO TOOLS. The safety prime has a short learning curve. Press works just as well without but the priming is slower. I replaced my Rock Chucker with it and now my Dillon SDB is getting jealous. The unit produces great ammo. With the safety prime system I can run 3-4 rounds a minute. Currently loading 10mm auto and .357 magnum on it. This press is light years ahead of the old pro 1000 I had (and gave a negative review to). I can't say enough good things about this press.
                  Bill Williams of Sunnyside, NY
                  Date posted: 11/3/2006
                  I fist read about the Lee Classic press in a review in Guns & Ammo magazine, and I decided to try one since I have a RCBS rockchucker. The production rate was quite impressive although there is a learning curve with the safety prime and auto disk powder dispenser. Initially, the pictures in the instructions needed better amplification and labeling which would have made the start-up easier. Watch out for the installation of the return spring on the autodisc dispenser -it requires some strength and dexterity to install it. The other complaint I had was you definitely need a riser for the autodisc in order to use dies which are not Lee's. The production rate is slightly slower than a friend's Dillon 550 but for 1/4 the price you can't beat it. Well constructed and engineered! And I even bought it on sale from Midway!!!
                  Bob R of Sunrise, Fl
                  Date posted: 5/28/2008
                  I have had this press for over two years now. I've successfully loaded thousands of rounds with it, and have had no problems with it except for a minor primer feed issue, (just keep a few primers in the slot and you will not have an issue). Set up was straight forward. The ram and linkage are solid and smooth in operation. I've loaded 7.62x54R, 7.62X39, 303 British, 223 REM, 30-06, 308, 8x57 and many many more. Any indexing issue can be adjusted very quickly and easily by following the directions or on Lee's website. The Auto Index feature is great for loading quantities of rifle ammo. I can see that it would work as well for pistol ammo .. but I have a Lee Pro 1000 for that. If you are looking to update your single stage or if you are new to reloading this is the press for you. Easy to use, dependable and the price is right. It has replaced my Rock Chucker and Lyman Turret Press. I Love IT! Thank you Lee.
                  Steven Pilchman of Pembroke Pines, FL
                  Date posted: 5/5/2009
                  This is a great press that I bought to replace my RCBS RockChucker single stage press which is also excellent. Once setup this press delivers precise indexing and is sturdy and like all Lee products incorporates engineering that delivers value well beyond the price. My only advise to those contemplating a purchase of this press is to invest in a few of the little square Lee Classic 4 Hole Turret Press Indexing Ratchets. My press came with an extra one and I needed to use it as the one that was in the press became distorted during my initial setup. Once I installed the replacement the press indexed perfectly and I cranked out a 100 .44 mag rounds and a hundred .223 Rem rounds. The little square plastic indexing ratchet only costs $1.99 and it will probably pay to have a few extra on hand.
                  Ron Wilmot of Holland, MI
                  Date posted: 3/9/2006
                  Like the other post, I am really impressed with this unit. I unpacked, mounted (Drill/tap my bench plate) installed Safety Prime and Pro Auto Disk, Installed dies and loaded 100 38 spl rounds in the first 1.5 hours of having this unit. Easy to operate, the safety prime unit takes some getting used to, but it works fairly well. Not as fast as my Hornady Lock-N-Load, but lots faster than the Rockchucker. I bought this press to do low volume accuracy rounds for rifle to replace the single stage but will be using it for a lot more.
                  fredrick mccollum of chula vista, ca
                  Date posted: 9/13/2007
                  First of all nothing is perfect. After reloading on an RCBS Rockchucker for over 10 years, this is the press I have been waiting for. It has the best features of single stage presses and none of the faults of progressive presses. At this point this press with all of the accessories will replace my RCBS Rockchucker reloading kit as my primary reloading tool. I want to thank the staff at Lee because I really wanted the Loadmaster but they explained that unless I was shooting over 200 rounds daily a progressive was not necessary. That saved me money and gave me a press that I can check each and every process. I can't wait to start reloading 308 Winchester on this press. This is not a huge step up from the single stage press but certainly speeds up the process nicely. I didn't give this press 5 stars because nothing is perfect but this press is perfect for me and my reloading needs.
                  Dave A of SE, ma
                  Date posted: 1/18/2010
                  I've owned all types of presses and have settled on this one as the perfect match of speed and control. While not as fast as the (Lee and Dillon) full progressive presses I've had, it will EASILY produce a box of 50 rounds every 15-20 min. That's enough for me ( and I suspect most other shooters too). Yet, the 4 stroke per round really gives you a sense of control and safety while loading. ( Fewer hiccups too!) Other benefits include simplified set-up and change over, best (anywhere!) primer catch system, improved/safer primer feed, and smooth solid operation. It's also nice that this one press will reload everything from 380 ACP to huge rifle cartridges without major cost or grief. This Classic Turret, (with a 4 die set and pro(!) powder measure is the end of the rainbow for me. This will be my last and all-time favorite press!
                  T T of Charlottesville, VA
                  Date posted: 11/29/2009
                  I bought a Dillon and this press at the same time. My intention was to use the Lee for small batch loads. To my surprise, I like the simplicity of the turret better than a progressive. If you load a moderate amount of various calibers, then it's hard to beat a turret press. Primers due tend to go everywhere without the primer arm installed. I prefer to prime off the press, so I cut the top off of one of the priming arms and now use it as a deflector. The primers now eject properly and the priming tool is out of my way when I resize.
                  Revolvers are not pistols

                  pistol nouna handgun whose chamber is integral with the barrel
                  Calling a revolver a "pistol" is like calling a magazine a "clip", calling a shotgun a rifle, or a calling a man a woman.

                  ExitCalifornia.org

                  Comment

                  • #10
                    Noah3683
                    Senior Member
                    • Aug 2009
                    • 2256

                    Thanks guys you're really making that kempf's deal look screamin. I think I'll go with that one
                    Originally posted by Neil McCauley
                    Are you actually suppost to "taste" wood?
                    Originally posted by Neil McCauley
                    Just wish I knew what wood in your meat is suppost to taste like.

                    Comment

                    • #11
                      fullspeed1
                      Senior Member
                      • Nov 2008
                      • 1908

                      I started with a Lee Classic single stage then purchased a Classic turret. The Turret was Definitely a step in the right direction for producing quantity. I now own a Dillon 550 and will never look back. In hindsight, The experience of a single stage was good. But, In this Hobby you need to buy once, cry once. Reloading 223 takes more than a just a reloading kit from cabelas or kempfs or wherever else. You need to take into consideration case prepping...Trimming, deburring, chamfering and swaging out military crimps. With all that in mind, Good luck in your journey.

                      Comment

                      • #12
                        XDRoX
                        Veteran Member
                        • Mar 2009
                        • 4420

                        I don't think you can go wrong with the LCT from Kempf's. The press alone was just on sale last week at Midway for $85. I should have picked it up then. It's back to just under $100 now I think. Even though I load on a Dillon now I really want a LCT for the bench because I've never owned one. Next time it goes on sale I'll pick one up.
                        Chris
                        <----Rimfire Addict


                        Originally posted by Oceanbob
                        Get a DILLON...

                        Comment

                        • #13
                          LGB Loader
                          Senior Member
                          • Jun 2008
                          • 727

                          Even though I load on a Dillon now I really want a LCT for the bench because I've never owned one. Next time it goes on sale I'll pick one up.
                          Chris,

                          I concur. Fact is, I am starting a renovation on my garage and house, nothing too major, just have to pack up "The Cave" for a few months and I'll be downsizing to the Lee Classic Turret.

                          My buddy, Brian, has one and I have used it a bit and really like this press. I believe the LCT and a good single stage is pretty much all most shooters out there really need.

                          LGB
                          Training in The Peaceful Art to achieve unnatural naturalness and natural unnaturalness, BEcoming WATER while serving The Great I AM.

                          John 3:16

                          Comment

                          • #14
                            Noah3683
                            Senior Member
                            • Aug 2009
                            • 2256

                            Originally posted by fullspeed1
                            I started with a Lee Classic single stage then purchased a Classic turret. The Turret was Definitely a step in the right direction for producing quantity. I now own a Dillon 550 and will never look back. In hindsight, The experience of a single stage was good. But, In this Hobby you need to buy once, cry once. Reloading 223 takes more than a just a reloading kit from cabelas or kempfs or wherever else. You need to take into consideration case prepping...Trimming, deburring, chamfering and swaging out military crimps. With all that in mind, Good luck in your journey.
                            I know there's more to it, was just looking for a decent kit on a budget to get a lot of the main components
                            Originally posted by Neil McCauley
                            Are you actually suppost to "taste" wood?
                            Originally posted by Neil McCauley
                            Just wish I knew what wood in your meat is suppost to taste like.

                            Comment

                            • #15
                              LGB Loader
                              Senior Member
                              • Jun 2008
                              • 727

                              Hi, Noah,

                              I did kinda overwhelm the question. Sorry...
                              That Lee Anniversay Kit is not a bad way to start, by the way. I have an old Challanger without the breech locks and it has held it's own nice. Not a nice, solid or smooth as the Redding's or even the Lee Classic Cast but it works okay and it was very affordable.

                              Fact is, that Lee Anniv. kit is better than what I started out with. My bench was an old 2 x 4 and my press was a hammer. And I ain't too press snobby to know that if I can't assemble great ammo with that Lee Anniv. Kit, then I shouldn't be handloading. Tools are just that, tools and good craftsmanship is just that, good craftmanship.

                              LGB
                              Training in The Peaceful Art to achieve unnatural naturalness and natural unnaturalness, BEcoming WATER while serving The Great I AM.

                              John 3:16

                              Comment

                              Working...
                              UA-8071174-1