Unconfigured Ad Widget

Collapse

10MM Compressed Powder Loading

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • robert101
    Senior Member
    • Sep 2009
    • 1997

    10MM Compressed Powder Loading

  • #2
    weatherman
    Banned
    • Nov 2008
    • 149

    Does the manual list that load as a compressed load at the maximum? There should be an asterisk...

    If not, I'd check everything really well. Verify scale function, etc.

    What is the suggested starting grains for the bullet and powder you are using?

    Comment

    • #3
      halifax
      Veteran Member
      • Oct 2005
      • 4440

      You are new to reloading. Don't start with a BANG. 10mm, Blue Dot, compressed loads.

      Definitely consider checking your scale and everything else.

      A new dime weighs APPROXIMATLY 35gr.

      Do you know any reloaders who might double check what you are trying to do?
      Last edited by halifax; 09-29-2009, 4:37 PM.
      Jim


      sigpic

      Comment

      • #4
        Mikeb
        Veteran Member
        • May 2008
        • 3189

        [QUOTE=halifax;3132846]You are new to reloading. Don't start with a BANG. 10mm, Blue Dot, compressed loads.

        Definitely consider checking your scale and everything else.

        A new dime weighs APPROXIMATLY 35gr.

        /QUOTE]

        That's a hot tip
        thanks
        Mike

        Comment

        • #5
          robert101
          Senior Member
          • Sep 2009
          • 1997

          Actually I didn't start with a hot load but at the mild end of the spectrum. I did check my scale using a penny (32 grains) and found my scale measured 35 grains. Ok, not bad and at least it is measuring maybe a little heavy.

          I am actuall loading a progressive series of handloads. For instance, I started with 6 cartridges at 9.7, then (6) at 10.2, then (6) at 10.7. Again, all of these loads are well below the * asterik or "c" load shown in the Lee's Manual.

          I'm not the most experienced reloader but I feel that my methodology is fine. Any other helpful suggestions?
          Robert

          Comment

          • #6
            robert101
            Senior Member
            • Sep 2009
            • 1997

            Ok, I just weighed two dimes and found the measurement to be about 39.4 grains each. This is less than the 35 grains suggested by MikeB. Again, if anything the scale is sightly light - not heavy.

            Comment

            • #7
              f4tweet
              Senior Member
              • Oct 2005
              • 2022

              Buy a scale check weight set. I don't like Blue Dot because of the flash. I like AA-7, or AA-9

              Comment

              • #8
                robert101
                Senior Member
                • Sep 2009
                • 1997

                Guys, all good advice about checking the scale and starting off with a minimal load. I plan on firing the lower loaded loads first and checking for excessive case expansion with my calipers. Does anyone have any actual experience with the 10MM Blue Dot powder charge and can relate to how it fills the case?

                I've looked up other resources for Blue Dot and found confirmation that even 10.7 is not the maximum charge. The Alliant Powder site shows also 11.5 as the maximum charge. Thanks for help here.
                Robert

                Comment

                • #9
                  halifax
                  Veteran Member
                  • Oct 2005
                  • 4440

                  Originally posted by robert101
                  Guys, all good advice about checking the scale and starting off with a minimal load. I plan on firing the lower loaded loads first and checking for excessive case expansion with my calipers. Does anyone have any actual experience with the 10MM Blue Dot powder charge and can relate to how it fills the case?

                  I've looked up other resources for Blue Dot and found confirmation that even 10.7 is not the maximum charge. The Alliant Powder site shows also 11.5 as the maximum charge. Thanks for help here.
                  Robert
                  Did any of those resources indicate whether your load was a compressed load? That is a common notation.

                  My Speer manual notates compressed loads with a "C". It does NOT show a "C" for 155gr and up to 12.0gr of Blue Dot. Something is not right.

                  How far below the lip of the cartridge (after tapping lightly) is the top of the 10.7gr?
                  Jim


                  sigpic

                  Comment

                  • #10
                    sammy
                    Veteran Member
                    • Oct 2006
                    • 3847

                    This is what 10.7 grains of Blue Dot looks like in a Starline case. It should not be compressed with a 165 grain bullet. Tripple check the load and make sure it is correct. The bullet is a 180g. Montana Gold BTW.

                    Comment

                    • #11
                      sammy
                      Veteran Member
                      • Oct 2006
                      • 3847

                      Here is a case full to the top. 17.5 grains of Blue Dot. Can you say kaboom?

                      Comment

                      • #12
                        DarkHorse
                        Senior Member
                        • Jan 2009
                        • 935

                        I posted in the other thread you made in Handguns, but I'll toss my hat in here, too.

                        Make sure it's a 10mm case, and you don't have mismarked .40's. You should have plenty of room with that load.
                        This is my sig line.

                        Comment

                        • #13
                          robert101
                          Senior Member
                          • Sep 2009
                          • 1997

                          That picture was very helpful. I'd say the top of my Blue Dot load was about 1/8" from the top of the brass. The picture looks to be more like a 1/4 to 3/8". That 180 grain bullet looks like it would come close to the top of the charge. One MAJOR point - I did not tap the case or compact at all after thorwing the powder in the case.

                          Also, the Speer Manual may not show a compressed charge at 12.0, but the Lee Manual shows a compressed charge at 11.5.

                          I'm going to go back and throw (double check weight) another 10.7 grains and fill a case to check for consistancy. Good information and thank you so much for the picture.
                          Robert

                          Comment

                          • #14
                            sammy
                            Veteran Member
                            • Oct 2006
                            • 3847

                            You are very welcome. Always happy to help a fellow shooter. The 10.7 load measures .315 from the top of the case. Again this is using starline brass.

                            Comment

                            • #15
                              robert101
                              Senior Member
                              • Sep 2009
                              • 1997

                              Sammy,
                              I sure hate to admit it, but I messed up the grains and tenths measurement settings on the scale. When I just double checked the charge, my measurement matches your pictures exactly. No, I wasn't drinking late last night when I set the scale but boy would I have been sorry if I had fired those rounds. Thanks so much for taking the time to send the pictures and help out. I am usually so careful in my loading but this one got away. Now its time to go back and fix the problem.
                              Robert

                              Comment

                              Working...
                              UA-8071174-1