Unconfigured Ad Widget

Collapse

First rounds loaded!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Requiem
    Senior Member
    • Dec 2008
    • 1725

    First rounds loaded!

    Alright, so tonight I decided to finally load my first rounds I will say it was a bit of an experimentation process as at first my rcbs uniflow powder measure wouldn't give consistent loads, then my first two rounds the COAL was a bit lower, so I backed out the seater plug on my die till I got the last two rounds right at or under 2.800



    My load was:

    147 grain bullet (resized from 7.62x54R)
    LC Brass
    WLR Primer
    41 grains of IMR 4895 (I originally planned 42, but backed down because the case looked a little full, any advice on this? I'm using resized 7.62x54R bullets which are longer than normal .308)



    Should I make a few batches of increased loads for a range day prior to going? I don't want to waste a day at the range only testing one load and then packing up, but I also don't want to waste reloading components by finding that a load will be too hot and not using the ones developed past that charge. I suppose I could bring the bench there tho....

    This will probably be my plinking load in my M1A, so I'm not looking for anything super accurate.
    Thankyou to all members of this M14tfl and Calguns for helping me get started on reloading!
    Last edited by Requiem; 08-29-2009, 9:21 PM.
    .
  • #2
    Darklyte27
    Calguns Addict
    • May 2008
    • 9372

    congrats, where you goin to shoot it?
    2 HANDGUNS STOLEN! 1 RECOVERED READ HERE

    Chickens

    Want to get into Ham Radio? Click here
    http://www.calguns.net/calgunforum/s...d.php?t=202581

    Comment

    • #3
      Requiem
      Senior Member
      • Dec 2008
      • 1725

      Thankyou, sir. I'm not quite sure yet... probably in the hills of the sonora area since I have a family member up there (along with my rifle), plus it doesn't cost me ten bucks to shoot there, only a couple of hours drive.
      .

      Comment

      • #4
        NRAhighpowershooter
        Super Moderator
        CGN Contributor - Lifetime
        • Jun 2003
        • 6485

        even with the long bullets.. 41-42 gr is perfectly fine for blasting ammo
        'Just Don't Point, Squint, and Laugh! '

        Distinguished Rifleman Badge #2220

        Comment

        • #5
          Requiem
          Senior Member
          • Dec 2008
          • 1725

          Originally posted by NRAhighpowershooter
          even with the long bullets.. 41-42 gr is perfectly fine for blasting ammo
          Thanks for the reassurance. However, I'm slightly concerned whether or not as I increase the charge, I will get a "crunch" when seating the bullet. I guess I am going to have to find that one out on my own.
          .

          Comment

          • #6
            tdc57
            Senior Member
            • Apr 2009
            • 560

            Right ON!!! Congrads!! It’s a great feeling knowing that you can reload your own ammo!.. And after a few more months of this, you’ll have better ammo that you can purchase!..

            Once again Congratulations on your first of many!..

            Comment

            • #7
              f4tweet
              Senior Member
              • Oct 2005
              • 2022

              My M1A likes 41.0 of IMR 4895 with a Sierra 168 gr SMK, 2.800 OAL. I tried longer rounds with more powder, but this was my plinker. Take a look at this site.

              Welcome to Jim Owens' JarHeadTop.com. This site is dedicated to the High Power shooting enthusiast, providing articles, tips, products, and instructional material for both the beginner and the veteran shooter.


              Comment

              • #8
                Bongos
                Veteran Member
                • Oct 2005
                • 4095

                7.62x54R is .311 dia bullets instead of .308 dia bullets for the 308, increase bullet diameter will increase pressure in you chamber. Do not know if this is safe.

                Comment

                • #9
                  Requiem
                  Senior Member
                  • Dec 2008
                  • 1725

                  Alrighty... Got a range report from these babies.

                  The situation: Warm day, probably mid-high 80's. Altitude appx 3600 ft. Target at a distance of 10 yards (didn't have much room to work with). Rifle was a M1A Socom 16 with approximately 800 rounds shot by me through the barrel. Sling and shooting jacket in the prone were used along with rapid fire strings. 5 or so minute cool down period in between every 5 round string of fire.

                  Bear with me, I'm not 100% sure how to measure group sizes, but I measured from the outside of the two farthest shotholes of the group.
                  My best group was:

                  41.2 grains IMR 4895 with a group size of 1.18" (minus one flyer due to shooter error)



                  Other group sizes were:

                  41.0 grains = ------ (I didn't bother measuring)
                  41.4 grains = 1.89"
                  41.6 grains = 1.82"



                  So now I'm wondering if I should continue increasing until a max load of 43.0 grains or if I should keep it in between 41 and 42. I do want to be able to shoot as far with a load as possible with my Socom.

                  I think it's safe to say I'm not going to test reloads for a while until I replace the ridiculous sights to scout sights.
                  .

                  Comment

                  • #10
                    Bongos
                    Veteran Member
                    • Oct 2005
                    • 4095

                    at 10 yards the bullet hasn't even stabalize..

                    Comment

                    • #11
                      tamalpias
                      Senior Member
                      • Aug 2009
                      • 1984

                      To bad you live so far away or i'd show you the basics. But heck man those books about reloading are so conservative that you can push it to max publications without any problems. They don't want to get sued so even in the newer books you will see lower pressure data used as the max pressure for these handloads.

                      So anyways, you are fine but I would go out at least 50-100 yards to test for accuracy because at 10 yards you aint got much to go on. I would have gone .5 gr. increments until i hit max load (i am assuming you have a rifle checked out to make sure it can perform under safe pressures). So far with my 3 rifles that I reload for i notice the most accurate group tends to be near the higher end of the powder charge and on my 22-250 with a 40 gr. bullet max charge of 37.5 gr. varget powder is what it likes best. I can get .75" groups at 100 yards with that load where a factory round I could only get about a 1.25" group.

                      Comment

                      • #12
                        tango5
                        Senior Member
                        • Dec 2008
                        • 2276

                        I would test it at 100yds instead of the 10yds you tested it on, before you start upping the load charges. Like bongos said, the bullet hasnt started to stabilize in the air at 10 yards. In my Rem 700 .308, i uses 42gr of Varget, WRL primers, and 168gr Sierra Match Kings and get very nice sub MOA groups at 100 yards.
                        US Army Veteran
                        1995-2003 31U Commo Chief

                        "You cannot invade mainland America. There would be a rifle behind every blade of grass" -Japanese Admiral Isoroku Yamamoto (WW2)

                        Comment

                        Working...
                        UA-8071174-1