Unconfigured Ad Widget

Collapse

Yet another reloading question....

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • anotherted
    Senior Member
    • Dec 2005
    • 1198

    Yet another reloading question....

    Hey there,

    Ive been sizing my brass with a LE Wilson trimmer and measuring the case length with a Frankford Arsenal digital caliper. From my reading, it looks like the length of the resized case should be @ 2.005" (.308 cal.). Ive messed with the trimmer to get it as accurate as i can but when i measure the case, i get different sizes none the less. For example, i get 2.005" for one, then trim the next case and get 2.0035", then another @ 2.0045", then another @ 2.0065", etc. I realize that i am dealing in thousandths of an inch, but how precise do i need to be in getting the length 100% on the nose @ 2.005"?

    Also, when i deburr will this reduce the length of the case?

    Thanks,

    Ted
    <bof>all your guns are belong to us</bof>
  • #2
    LCAZES
    Member
    • Mar 2003
    • 178

    You are now within measurement error for most calipers. If I recall "2.005 is the SAAMI MAX OA case length for .308, correct?

    Comment

    • #3
      ivanimal
      Janitors assistant
      CGN Contributor - Lifetime
      • Sep 2002
      • 14365

      There is a minimum, which has to do with the grip on a bullet and aid in obteration, and a maximum, which has to do with pressure increase. As long as you stay within those limits you are fine. The average sportsman falls into this category bench rest shooters on the other hand are more precise in their needs for uniformity. The only reason I have my cases really close would be when using a crimp, or reloading the 45 ACP which headspaces on the case mouth. When using a crimp die if the cases were all different sizes you would have to adjust for each one. For 45 ACP you would get a lot os misfires or light primer strikes. The worst case scenario is when you do not trim and load max, the increase in pressure could be dangerous. I always measure for max. Not usually for Min unless I have to trim.
      "I would kill for a Nobel peace prize." Steven Wright"
      Board Member CGSSA Donate now!
      NRA lifetime member

      Comment

      • #4
        Vepr62
        Senior Member
        • Oct 2006
        • 1216

        Use LEE hand trimer. It consists of a cutter attached to a guage pin, and a shell holder. You affix your shell to a shell holder, insert the pin guage inside and through the primer hole, few turns until your pin hits the bottom of a shell holder and you are done. Same lenght EVERY time.
        Vasiliy

        Comment

        • #5
          anotherted
          Senior Member
          • Dec 2005
          • 1198

          Originally posted by ivanimal
          There is a minimum, which has to do with the grip on a bullet and aid in obteration, and a maximum, which has to do with pressure increase. As long as you stay within those limits you are fine.
          So what is the minimum and maximum?
          <bof>all your guns are belong to us</bof>

          Comment

          • #6
            Vepr62
            Senior Member
            • Oct 2006
            • 1216

            Actually standard lenght for .308 Winchester is 2.015, not 2.005, and my cutter does exactly that. I have found that Hornady once fired brass does not need treeming. Remington brass is not very consistent in lenght, some cases are ok, and some need treeming. The longest bras is Federal. I treem all federal once fired brass. If i bring brass from the range, I resize whole case, and brass from my rifle, I resize the neck only. Deburring won't change case lenght. Hope this helps.

            Vasiliy
            Last edited by Vepr62; 12-11-2006, 12:14 AM.

            Comment

            • #7
              anotherted
              Senior Member
              • Dec 2005
              • 1198

              I would simply like to know what the minimum and maximum case lengths are for the .308., and if the fluctuations in my case measurements are ok.
              <bof>all your guns are belong to us</bof>

              Comment

              • #8
                ocabj
                Calguns Addict
                • Oct 2005
                • 7924

                2.005 is the minimum. 2.015 is the maximum. This is from all manuals I own and have seen.

                I trim to 2.007. I don't trim to the bare minimum. I like to trim to slightly above. Plus, I load ammo in batches, thus I process brass in batches. For .308 specifically, I use Lapua from 100ct boxes. I keep brass from each box together, separated from the brass from other boxes. I trim all the brass in each box/batch to the same length. In this case, around 2.007. As long as all the brass in that specific batch is the same length, that is my main concern as far as case length.

                You can always trim to 2.015, but the key to accuracy is consistency. In order for you to be consistent while trimming to a longer length, all the brass in your batch needs to be growing to or above 2.015 in order for you to trim it to the same length. That's why you trim to or close to the minimum.

                Distinguished Rifleman #1924
                NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
                NRL22 Match Director at WEGC

                https://www.ocabj.net

                Comment

                • #9
                  anotherted
                  Senior Member
                  • Dec 2005
                  • 1198

                  Perfect, thats exactly the information ive been looking for. Thanks ocabj.
                  <bof>all your guns are belong to us</bof>

                  Comment

                  • #10
                    ocabj
                    Calguns Addict
                    • Oct 2005
                    • 7924

                    Originally posted by anotherted
                    Perfect, thats exactly the information ive been looking for. Thanks ocabj.
                    No problemo.

                    Oh, in response to your question about deburing the case neck, it doesn't 'trim' the case length. What you may notice is that when you trim brass (and quite a bit is trimmed off since the brass is long), the neck face becomes flat and has brass bunched up around the outside diameter. You want to debur the inside and outside diameter before you measure the case length so that excess brass in the inside/outside doesn't affect your measurement.

                    Of course, it's possible to 'trim' brass with a deburring tool if you chuck it into some kind of power tool (cordless drill, drill press) and really go at it for too long. But by hand, it's pretty hard to shorten brass length with a hand deburring tool.

                    Distinguished Rifleman #1924
                    NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
                    NRL22 Match Director at WEGC

                    https://www.ocabj.net

                    Comment

                    • #11
                      50ae
                      Senior Member
                      • Oct 2005
                      • 572

                      I must say, I've never trimmed my 45's and haven't had a problem but now you've made me paranoid so I'll have to go measure a representative sample of my cases. Now, being that I have about 30k of spent cases that means I'll have to do a lot of measuring and being that I'll probably find differences I'll end up finally buying a trimmer which means I'm going to end up in a fight with the wife over money so therefore, thanks for starting a fight between my wife and I BTW, my guess is that I'll end up with one of those Dillon trimmers that mount on my press, good thing I worked out in CA the last two months and took my big CA money back to TX

                      Originally posted by ivanimal
                      There is a minimum, which has to do with the grip on a bullet and aid in obteration, and a maximum, which has to do with pressure increase. As long as you stay within those limits you are fine. The average sportsman falls into this category bench rest shooters on the other hand are more precise in their needs for uniformity. The only reason I have my cases really close would be when using a crimp, or reloading the 45 ACP which headspaces on the case mouth. When using a crimp die if the cases were all different sizes you would have to adjust for each one. For 45 ACP you would get a lot os misfires or light primer strikes. The worst case scenario is when you do not trim and load max, the increase in pressure could be dangerous. I always measure for max. Not usually for Min unless I have to trim.
                      Proud to be a SoCal expatriate currently living in DFW, TX.

                      Comment

                      • #12
                        ivanimal
                        Janitors assistant
                        CGN Contributor - Lifetime
                        • Sep 2002
                        • 14365

                        Thank you ocabj for getting the info out so fast!

                        The subsonic cases such as the 9MM 45ACP 38 special................do not create enough heat aka pressure to cause brass flow. Brass flow is the reason we must trim. I have never had to trim 45 ACP but do measure anyway. I have a gauge that makes it easy, too easy to not do it. I do this while examining the cases for flaws.

                        "I would kill for a Nobel peace prize." Steven Wright"
                        Board Member CGSSA Donate now!
                        NRA lifetime member

                        Comment

                        • #13
                          thmpr
                          Veteran Member
                          • Dec 2005
                          • 3785

                          For the 223 and 6.8, trimming is a must. As long it is within the max and min specs, no trimming is required. But I normally trim all my cases to min specs due to metal expansion after firning and sizing. The Giraud trimmer is a must when high volume of trimming is required.
                          For the 6.5 Grendel, no trimming required after 4 re-loads. Maybe due to the hardness criteria.
                          NRA Life Member

                          Comment

                          • #14
                            xrMike
                            Calguns Addict
                            • Feb 2006
                            • 7841

                            Originally posted by 50ae
                            I must say, I've never trimmed my 45's and haven't had a problem but now you've made me paranoid so I'll have to go measure a representative sample of my cases.
                            Don't bother! Nobody trims .45ACP (or any other straight-walled brass). The only brass that grows longer from shooting are the "necked" calibers.

                            .45ACP actually shrinks a little, the more you shoot it.

                            Comment

                            • #15
                              50ae
                              Senior Member
                              • Oct 2005
                              • 572

                              OK Animal, where did you get that guage? I must have one!!!!

                              I didn't think anyone trimmed 45's but I just wanted to be sure. I have loaded well over 200k 45's on my Dillon and never had a problem but it is always good to learn new tricks.
                              Proud to be a SoCal expatriate currently living in DFW, TX.

                              Comment

                              Working...
                              UA-8071174-1