Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
9mm conflicting load data ?
Collapse
X
-
The max charge for a .356 115gr bullet is 4.3gr of tg. It's 4.8 for a .355 gdhp, but you can use gdhp data for any other .355 bullet so long as you're mindful of oal. RN will be loaded longer by a decent amount.
4.2 would work fine. It's not really in conflict of published data.Comment
-
OAL makes a HUGE difference...
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 10.030 grain H2O = 0.651 cm³ Cartridge O.A.L. L6: 1.169 inch = 29.69 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 47 3.51 931 221 17629 3296 100.0 0.558 -20.0 48 3.61 950 230 18619 3370 100.0 0.543 -17.8 49 3.71 968 239 19640 3444 100.0 0.529 -15.5 51 3.81 986 248 20694 3518 100.0 0.516 -13.3 52 3.91 1003 257 21781 3592 100.0 0.504 -11.1 53 4.01 1021 266 22901 3665 100.0 0.492 -08.9 55 4.11 1038 275 24055 3738 100.0 0.481 -06.7 56 4.21 1054 284 25244 3811 100.0 0.470 -04.4 57 4.31 1071 293 26468 3884 100.0 0.460 -02.2 59 4.41 1087 302 27727 3956 100.0 0.450 [B]+00.0 60 4.51 1104 311 29023 4028 100.0 0.441[/B] +02.2 61 4.61 1120 320 30356 4100 100.0 0.432 ! Near Maximum ! +04.4 63 4.71 1135 329 31727 4171 100.0 0.424 ! Near Maximum ! +06.7 64 4.81 1151 338 33137 4243 100.0 0.415 ! Near Maximum ! +08.9 65 4.91 1167 348 34586 4313 100.0 0.408 !DANGEROUS LOAD-DO NOT USE! +11.1 66 5.01 1182 357 36075 4384 100.0 0.400 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 60 4.51 1110 315 30194 4001 100.0 0.434 ! Near Maximum ! Data for burning rate decreased by 3% relative to nominal value: -Ba 60 4.51 1096 307 27837 4059 100.0 0.449
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 8.927 grain H2O = 0.580 cm³ Cartridge O.A.L. L6: 1.125 inch = 28.58 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 52 3.51 961 236 20330 3191 100.0 0.526 -20.0 54 3.61 980 245 21510 3262 100.0 0.512 -17.8 55 3.71 998 254 22731 3332 100.0 0.499 -15.5 57 3.81 1016 264 23994 3402 100.0 0.487 -13.3 58 3.91 1034 273 25300 3472 100.0 0.475 -11.1 60 4.01 1052 283 26649 3542 100.0 0.464 -08.9 61 4.11 1070 292 28044 3611 100.0 0.453 -06.7 63 4.21 1087 302 29484 3680 100.0 0.443 -04.4 64 4.31 1104 311 30970 3749 100.0 0.434 ! Near Maximum ! -02.2 66 4.41 1121 321 32505 3817 100.0 0.424 ! Near Maximum ! [B]+00.0 67 4.51 1137 330 34088 3885 100.0 0.416 ! Near Maximum ![/B] +02.2 69 4.61 1154 340 35722 3953 100.0 0.407 !DANGEROUS LOAD-DO NOT USE! +04.4 70 4.71 1170 350 37407 4020 100.0 0.399 !DANGEROUS LOAD-DO NOT USE! +06.7 72 4.81 1186 359 39145 4087 100.0 0.391 !DANGEROUS LOAD-DO NOT USE! +08.9 73 4.91 1202 369 40937 4153 100.0 0.384 !DANGEROUS LOAD-DO NOT USE! +11.1 75 5.01 1218 379 42785 4219 100.0 0.377 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 67 4.51 1143 334 35478 3858 100.0 0.409 !DANGEROUS LOAD-DO NOT USE! Data for burning rate decreased by 3% relative to nominal value: -Ba 67 4.51 1130 326 32681 3915 100.0 0.422 ! Near Maximum !
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 7.049 grain H2O = 0.458 cm³ Cartridge O.A.L. L6: 1.050 inch = 26.67 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 66 3.51 1019 265 27760 2973 100.0 0.467 -20.0 68 3.61 1039 276 29507 3036 100.0 0.454 -17.8 70 3.71 1058 286 31329 3099 100.0 0.443 ! Near Maximum ! -15.5 72 3.81 1077 296 33226 3161 100.0 0.432 ! Near Maximum ! -13.3 74 3.91 1096 307 35201 3222 100.0 0.421 !DANGEROUS LOAD-DO NOT USE! -11.1 76 4.01 1115 317 37259 3284 100.0 0.411 !DANGEROUS LOAD-DO NOT USE! -08.9 78 4.11 1133 328 39401 3345 100.0 0.402 !DANGEROUS LOAD-DO NOT USE! -06.7 79 4.21 1152 339 41631 3405 100.0 0.393 !DANGEROUS LOAD-DO NOT USE! -04.4 81 4.31 1170 349 43952 3465 100.0 0.384 !DANGEROUS LOAD-DO NOT USE! -02.2 83 4.41 1187 360 46367 3524 100.0 0.376 !DANGEROUS LOAD-DO NOT USE! [B]+00.0 85 4.51 1205 371 48882 3583 100.0 0.368 !DANGEROUS LOAD-DO NOT USE![/B] +02.2 87 4.61 1223 382 51499 3641 100.0 0.361 !DANGEROUS LOAD-DO NOT USE! +04.4 89 4.71 1240 393 54224 3699 100.0 0.353 !DANGEROUS LOAD-DO NOT USE! +06.7 91 4.81 1257 404 57060 3756 100.0 0.346 !DANGEROUS LOAD-DO NOT USE! +08.9 93 4.91 1274 415 60014 3812 100.0 0.340 !DANGEROUS LOAD-DO NOT USE! +11.1 95 5.01 1291 426 63090 3868 100.0 0.333 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 85 4.51 1211 374 50913 3558 100.0 0.363 !DANGEROUS LOAD-DO NOT USE! Data for burning rate decreased by 3% relative to nominal value: -Ba 85 4.51 1199 367 46825 3611 100.0 0.373 !DANGEROUS LOAD-DO NOT USE!
Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
you can always call them. I have talked with them a couple of times about loads and they have been awesome. Here is what is in their book for 115's.Comment
-
Where is this data from? It has me concerned about some of my loads for 124gr projectiles. Only because of the varying data from different sources and what is "max" pressure. Although I generally load at or near starting loads and chrono I would really like to see a chart like this for 124gr with cfe pistol for comparison. The difference in OAL especially got my attention because for example sometimes I'm loading at 1.125 vs 1.150 for example.OAL makes a HUGE difference...
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 10.030 grain H2O = 0.651 cm³ Cartridge O.A.L. L6: 1.169 inch = 29.69 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 47 3.51 931 221 17629 3296 100.0 0.558 -20.0 48 3.61 950 230 18619 3370 100.0 0.543 -17.8 49 3.71 968 239 19640 3444 100.0 0.529 -15.5 51 3.81 986 248 20694 3518 100.0 0.516 -13.3 52 3.91 1003 257 21781 3592 100.0 0.504 -11.1 53 4.01 1021 266 22901 3665 100.0 0.492 -08.9 55 4.11 1038 275 24055 3738 100.0 0.481 -06.7 56 4.21 1054 284 25244 3811 100.0 0.470 -04.4 57 4.31 1071 293 26468 3884 100.0 0.460 -02.2 59 4.41 1087 302 27727 3956 100.0 0.450 [B]+00.0 60 4.51 1104 311 29023 4028 100.0 0.441[/B] +02.2 61 4.61 1120 320 30356 4100 100.0 0.432 ! Near Maximum ! +04.4 63 4.71 1135 329 31727 4171 100.0 0.424 ! Near Maximum ! +06.7 64 4.81 1151 338 33137 4243 100.0 0.415 ! Near Maximum ! +08.9 65 4.91 1167 348 34586 4313 100.0 0.408 !DANGEROUS LOAD-DO NOT USE! +11.1 66 5.01 1182 357 36075 4384 100.0 0.400 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 60 4.51 1110 315 30194 4001 100.0 0.434 ! Near Maximum ! Data for burning rate decreased by 3% relative to nominal value: -Ba 60 4.51 1096 307 27837 4059 100.0 0.449
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 8.927 grain H2O = 0.580 cm³ Cartridge O.A.L. L6: 1.125 inch = 28.58 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 52 3.51 961 236 20330 3191 100.0 0.526 -20.0 54 3.61 980 245 21510 3262 100.0 0.512 -17.8 55 3.71 998 254 22731 3332 100.0 0.499 -15.5 57 3.81 1016 264 23994 3402 100.0 0.487 -13.3 58 3.91 1034 273 25300 3472 100.0 0.475 -11.1 60 4.01 1052 283 26649 3542 100.0 0.464 -08.9 61 4.11 1070 292 28044 3611 100.0 0.453 -06.7 63 4.21 1087 302 29484 3680 100.0 0.443 -04.4 64 4.31 1104 311 30970 3749 100.0 0.434 ! Near Maximum ! -02.2 66 4.41 1121 321 32505 3817 100.0 0.424 ! Near Maximum ! [B]+00.0 67 4.51 1137 330 34088 3885 100.0 0.416 ! Near Maximum ![/B] +02.2 69 4.61 1154 340 35722 3953 100.0 0.407 !DANGEROUS LOAD-DO NOT USE! +04.4 70 4.71 1170 350 37407 4020 100.0 0.399 !DANGEROUS LOAD-DO NOT USE! +06.7 72 4.81 1186 359 39145 4087 100.0 0.391 !DANGEROUS LOAD-DO NOT USE! +08.9 73 4.91 1202 369 40937 4153 100.0 0.384 !DANGEROUS LOAD-DO NOT USE! +11.1 75 5.01 1218 379 42785 4219 100.0 0.377 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 67 4.51 1143 334 35478 3858 100.0 0.409 !DANGEROUS LOAD-DO NOT USE! Data for burning rate decreased by 3% relative to nominal value: -Ba 67 4.51 1130 326 32681 3915 100.0 0.422 ! Near Maximum !
Code:Cartridge : 9 mm Luger (SAAMI) Bullet : .355, 115, RN Rainier 9mm Useable Case Capaci: 7.049 grain H2O = 0.458 cm³ Cartridge O.A.L. L6: 1.050 inch = 26.67 mm Barrel Length : 4.0 inch = 101.6 mm Powder : Hodgdon TiteGroup Predicted data by increasing and decreasing the given charge, incremented in steps of 2.22% of nominal charge. CAUTION: Figures exceed maximum and minimum recommended loads ! Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time % % Grains fps ft.lbs psi psi % ms -22.2 66 3.51 1019 265 27760 2973 100.0 0.467 -20.0 68 3.61 1039 276 29507 3036 100.0 0.454 -17.8 70 3.71 1058 286 31329 3099 100.0 0.443 ! Near Maximum ! -15.5 72 3.81 1077 296 33226 3161 100.0 0.432 ! Near Maximum ! -13.3 74 3.91 1096 307 35201 3222 100.0 0.421 !DANGEROUS LOAD-DO NOT USE! -11.1 76 4.01 1115 317 37259 3284 100.0 0.411 !DANGEROUS LOAD-DO NOT USE! -08.9 78 4.11 1133 328 39401 3345 100.0 0.402 !DANGEROUS LOAD-DO NOT USE! -06.7 79 4.21 1152 339 41631 3405 100.0 0.393 !DANGEROUS LOAD-DO NOT USE! -04.4 81 4.31 1170 349 43952 3465 100.0 0.384 !DANGEROUS LOAD-DO NOT USE! -02.2 83 4.41 1187 360 46367 3524 100.0 0.376 !DANGEROUS LOAD-DO NOT USE! [B]+00.0 85 4.51 1205 371 48882 3583 100.0 0.368 !DANGEROUS LOAD-DO NOT USE![/B] +02.2 87 4.61 1223 382 51499 3641 100.0 0.361 !DANGEROUS LOAD-DO NOT USE! +04.4 89 4.71 1240 393 54224 3699 100.0 0.353 !DANGEROUS LOAD-DO NOT USE! +06.7 91 4.81 1257 404 57060 3756 100.0 0.346 !DANGEROUS LOAD-DO NOT USE! +08.9 93 4.91 1274 415 60014 3812 100.0 0.340 !DANGEROUS LOAD-DO NOT USE! +11.1 95 5.01 1291 426 63090 3868 100.0 0.333 !DANGEROUS LOAD-DO NOT USE! Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge Data for burning rate increased by 3% relative to nominal value: +Ba 85 4.51 1211 374 50913 3558 100.0 0.363 !DANGEROUS LOAD-DO NOT USE! Data for burning rate decreased by 3% relative to nominal value: -Ba 85 4.51 1199 367 46825 3611 100.0 0.373 !DANGEROUS LOAD-DO NOT USE!
Thanks for posting this.
Even though in 4-5 years of loading 9mm I have never loaded any 115gr, always 124gn I do have some I have never gotten in to yet but the way things are going I will need to use them.
Comment
-
That looks like QuickLoad output."San Francisco Liberal With A Gun"
F***ing with people's heads, one gun show at a time. Hallelujah!
http://www.sanfranciscoliberalwithagun.com (reloading info w/ videos)
http://www.liberalsguncorner.com (podcast)
http://www.youtube.com/sfliberal (YouTube channel)
----------------------------------------------------
To be a true Liberal, you must be 100% pro-Second Amendment. Anything less is inconsistent with liberalism.Comment
-
It's NOT actual test data.
It's a Quickload simulation of what a powder charge will do under specific conditions such as a 9mm case with a specific bullet seated at a specific overall length.
I simply ran 3 simulations while varying ONLY the overall length to show what the differences are from 3 different lengths.Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
Thanks for looking, appreciate it.
Not sure how it works in the real world because I've loaded at different OAL's and didn't see much difference. I'm thinking Titegroup is much hotter and changes therefore are more drastic. Maybe different powder, different characteristics though. CFE Pistol is a slower powder and always chrono's slower than expected and is sooty loaded on the lower end.
I think in my experience loading many thousands of rounds I'm still very inexperienced because I found certain safe loads, powders, projectiles for mostly target ammo and have stuck with them. Started with Bullseye and then found the CFE Pistol was less "snappy" before I understood why, burn rates, etc. Now I'm slightly more "enlightened", for instance the PC9 (17" barrel) with CFE Pistol, SRP and 147gr projectile, not so much what it does but why it does it. Concepts like why a heavier projectile requires less charge are hard to grasp at first but over time are understood. Now I have "tailored" loads for specific guns.
Time for more learning because I now have my first jugs of W231. The CFE Pistol was just too slow for .380 and I'm going to start using it in larger calibers where the CFE Pistol doesn't produce advertised velocities to see if it's more responsive.
Comment
-
Cfe pistol is pretty good for hotter loads. It's a really good powder. If you did a min load at 1.125 instead of 1.150, I wouldnt worry about it.
Look at the case fill percentages with titegroup. 4.5 grains is a full case. Cfe pistol is denser, so setback won't be as dramatic.Comment
-
No I'm not worried since I have loaded thousands that way.Cfe pistol is pretty good for hotter loads. It's a really good powder. If you did a min load at 1.125 instead of 1.150, I wouldnt worry about it.
Look at the case fill percentages with titegroup. 4.5 grains is a full case. Cfe pistol is denser, so setback won't be as dramatic.
5gn CFE Pistol, 1.250, Xtreme 124gn CPRN, 1100 fps out of my XD Tactical 5" barrel. Perfect range ammo and they shoot well out of all my guns.
Comment
Calguns.net Statistics
Collapse
Topics: 1,870,943
Posts: 25,177,738
Members: 358,862
Active Members: 5,392
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 45800 users online. 115 members and 45685 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment