Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
RCBS Charge master 1500 problem
Collapse
X
-
You using the straw trick or no straw trick? Did you run the calibration in a few different locations? Have you cleaned the round base of the pedestal lately and checked to see if any powder has lodged into the pedestal’s mounting hole?
Just a few thoughts on what it could be...
Mac.
.........??????????...... sigpic
.
???Everyone's a Garand expert until the Garand expert walks in the room and I have only met 3, Scott Duff, Bruce Canfield & Gus Fisher
.Comment
-
Lift out the plastic tray and blow in it. Really. Maybe a grain of powder is stuck somewhere.Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
I really miss the good old Pomona Gun Shows.
I'm Back.Comment
-
I found that using a fan or fluorescent lighting will make mine erratic, the fan simply by upsetting the air and the light from EM/RF interference.
There was also a recent post about powder in the weigh sensor area inside the housing causing zeroing issues.sigpic

Bob B.
(\__/)
(='.'=)
(")_(")Comment
-
Lights off. Just well lit By daylight room. No fan. Even went so far as to close the doors till I was sweating to death. Checked the plastic piece and blew into the opening. No straw trick.
Loaded about 400 rounds no problem. Then bam it went nutsLast edited by Clickjack; 07-10-2020, 2:16 PM.Comment
-
Take that scale and shake it to see if there's powder rolling around in there.
Is your reloading bench on carpet.
May sound weird. But static electricity does strange things.
Try putting the scale on a thick book.
Is it under warranty ?Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
I really miss the good old Pomona Gun Shows.
I'm Back.Comment
-
Hard wood Floor. Hard wood table. I doubt the warranty will cover me. But maybe they’ll fix it cheap. Also I can’t get a hold of them. Two emails weeks apart no one got back to me. and no answer on the phone Because of pandemicComment
-
Try loading in the morning because of cooler temps.
Also try these:
a) static spray - use it on your bench where the 1500 is situated.
b) surge protector - i'm sure you are using one
c) ferrite bead - use two beads, one near surge protector and one near where you plug into the 1500.Comment
-
If you can figure out what's on your AC line you're using to power your CM, try making sure that anything else is turned off or unplugged (easiest is to kill the breaker and see what else turns off). If you're in a multi-family structure (apartment, condo, etc) try a different time to eliminate other people's equipment affecting line voltage.
Make sure you isolate your CM from electric motors (i.e. fans and the like), radios (including cell phones, wireless computers, etc), and flourescent lights. This applies on AC power or the alternative below.
Consider getting a line voltage conditioner (pricey, I know); or at least putting a ferrite line filter on the power cord.
Alternatively, a lot of people have gone to powering their CM's with a battery (motorcycle or lawn and garden batteries seem to work.) Though the power input is listed as 15V (as I recall), the reports say they run fine at 12V.Comment
-
Calguns.net Statistics
Collapse
Topics: 1,870,971
Posts: 25,178,122
Members: 358,862
Active Members: 5,382
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 62304 users online. 74 members and 62230 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment