Unconfigured Ad Widget

Collapse

Electronic Bullet Seating Pressure Sensor

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • aczesz
    Junior Member
    • Aug 2018
    • 16

    Electronic Bullet Seating Pressure Sensor

    I have had the idea for a while to use a force resistance sensor mounted under the die in my arbor press to read bullet seat force. I have worked out the first designed and printed out a prototype as seen below. Now I am just waiting for the electronics to arrive! The end goal for this project is to be able to view the bullet seat force in lbs over time on a graph on the computer, automatic computing of first and second peak pressures, then sort the bullets into X number of groups based off of the first and second peak seating force. Overall the project should be inexpensive as the sensor itself is $7 and the micro controller (Arduino) is around $20. The actual program will be written in python and should be compatible with any operating system.
    Here are some photos of the CAD model as well as the first printed prototype:
    Capture1.jpg
    The entire assembly. Here you can see how the two parts fit together with the small groove for the sensor itself running from the outside to the middle.
    Capture2.jpg
    A cut away view from the side of the assembly that shows one of the locating pins and some of the chamfers on the components.
    Capture3.jpg
    The inner puck
    Capture4.jpg
    The bottom of the inner puck. You can see the holes for the locating pins as well as a raised circle in the middle to press on the sensor
    Capture5.jpg
    The lower puck with the sensor pocket as well as the 3 locating pins

    Next post will be some photos of the printed prototype!
    Last edited by aczesz; 04-28-2019, 8:45 PM. Reason: missmatch units
  • #2
    aczesz
    Junior Member
    • Aug 2018
    • 16

    I 3D printed a prototype on a Monoprice Maker Ultimate with a layer width of 0.1mm (0.004 inches). The printing process for both took about 3 hours total and fit together perfectly! Pretty surprised since I guessed on the tolerances of the printer. Photos of the printed product:
    _AC_5540.jpg
    The two pucks next to each other. The inside of the puck on the left is where the seating die sits. It is pretty rough in there because support material was printed in and i had to remove it with some needle nose pliers. You can clearly see the alignment pins as well as the pocket for the pressure sensor.
    _AC_5542.jpg
    The holes on the bottom of the top puck
    _AC_5543.jpg
    The two in their assembled state
    _AC_5544.jpg
    Pucks assembled with the die sitting in the upper puck!

    Comment

    • #3
      fguffey
      Senior Member
      • Mar 2010
      • 1408

      --------------------------------------------------------------------------------

      I have had the idea for a while to use a force resistance sensor mounted under the die in my arbor press to read bullet seat pressure.
      Too late, a reloader built one and posted the results. Money wise it was not that expensive. The hydraulic press was listed with links in the same thread. And then there was the conversation about tensions, all of the presses used gages that measured bullet hold in pounds because there is no gage that measures neck tension in tensions.

      Again, I have tension gages, none of my tension gages measure tensions; all of my tension gage measure in pounds. I use bullet hold measured in pounds, I can measure seating in pounds and bullet pulling in pounds but I find it impossible to measure bullet seating in tensions.

      F. Guffey

      Comment

      • #4
        aczesz
        Junior Member
        • Aug 2018
        • 16

        Do you have the link to that thread by any chance? It would be cool to see what someone else has already done!

        Comment

        • #5
          TKM
          Onward through the fog!
          CGN Contributor
          • Jul 2002
          • 10657

          You may get results but I'm not sure what they would mean. I don't believe there is an industry standard.
          It's not PTSD, it's nostalgia.

          Comment

          • #6
            fguffey
            Senior Member
            • Mar 2010
            • 1408

            --------------------------------------------------------------------------------
            Do you have the link to that thread by any chance? It would be cool to see what someone else has already done!
            I thought he made a brilliant effort but he posted his creation on a forum of hard to please reloaders. Because of his fine work I got the feeling he was from Australia or New Zealand.

            F. Guffey

            Comment

            • #7
              Mesa Defense
              Senior Member
              • Feb 2009
              • 2172

              Does this measure pressure on the bullet inward by the brass or the pressure required to install the bullet in the brass? Thanks.

              Comment

              • #8
                aczesz
                Junior Member
                • Aug 2018
                • 16

                Originally posted by TKM
                You may get results but I'm not sure what they would mean. I don't believe there is an industry standard.
                There really isnt an industry standard from what i can tell. Some presses that measure seating pressure use hydraulic pressure to give you the force and others use deflection of spring washers which gives you a reading in inches.

                The main advantage to what I am trying to build is I get to see the results after I have already pressed the bullet, and software will auto group bullets for me and/or give me statistics on that batch of brass. I will hopefully be able to track neck tension after every anneal and resize to see how good I am actually annealing the brass.

                Comment

                • #9
                  aczesz
                  Junior Member
                  • Aug 2018
                  • 16

                  Originally posted by Mesa Defense
                  Does this measure pressure on the bullet inward by the brass or the pressure required to install the bullet in the brass? Thanks.
                  Pressure required to install the bullet

                  Comment

                  • #10
                    M1NM
                    Calguns Addict
                    • Oct 2011
                    • 7966

                    Too many variances to be useful for reloading. Neck thickness, amount of dust/dirt/lube in neck, even temp which will expand or contract the case and bullet. An ammo manufacturer may need the info for machine specs but in the end they load to OAL also.

                    Comment

                    • #11
                      aczesz
                      Junior Member
                      • Aug 2018
                      • 16

                      Originally posted by M1NM
                      Too many variances to be useful for reloading. Neck thickness, amount of dust/dirt/lube in neck, even temp which will expand or contract the case and bullet. An ammo manufacturer may need the info for machine specs but in the end they load to OAL also.
                      And this is why reloading is more like an art than a science, but im going to try and get it as close to a science as i can! Take data and see if it is useful, then if its not try something else. Otherwise analyze the data to improve the process.

                      Comment

                      • #12
                        sofbak
                        Veteran Member
                        • Aug 2010
                        • 2628

                        ^^Well, whatever results from your endeavor, could you please rectify your
                        (future) descriptions of what you're attempting to measure?

                        "The end goal for this project is to be able to view the bullet seat pressure in lbs (or Nm) ...."
                        Tire kickers gonna kick,
                        Nose pickers gonna pick
                        I and others know the real

                        Comment

                        • #13
                          aczesz
                          Junior Member
                          • Aug 2018
                          • 16

                          Originally posted by sofbak
                          ^^Well, whatever results from your endeavor, could you please rectify your
                          (future) descriptions of what you're attempting to measure?

                          "The end goal for this project is to be able to view the bullet seat pressure in lbs (or Nm) ...."
                          Yes I will post the progress on the project as well as the final results with some example data

                          Comment

                          • #14
                            Aeneas
                            Senior Member
                            • Feb 2014
                            • 1127

                            This is interesting. I can see how this might be able to give you some useful data if you are looking to get toward the bleeding edge of consistency. It seems like the most likely help will be in telling you how you're doing in case prep and sorting.

                            Subscribed.

                            Comment

                            • #15
                              sofbak
                              Veteran Member
                              • Aug 2010
                              • 2628

                              Originally posted by aczesz
                              Yes I will post the progress on the project as well as the final results with some example data
                              Whoooooshh.

                              Looks like that suggestion flew right over your head...:nvm.
                              Tire kickers gonna kick,
                              Nose pickers gonna pick
                              I and others know the real

                              Comment

                              Working...
                              UA-8071174-1