Unconfigured Ad Widget

Collapse

Camming Over Question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • alexisjohnson
    Senior Member
    • May 2016
    • 651

    Camming Over Question

    Hey guys,

    I've started to reload .308 and when i bring down the resizing die to the point of contact, it is still a wee bit tight in my rifle where you can feel it when locking down the bolt. I've been doing some internet research and i came across this concept of camming over.

    I'm using a dillon 550 with all dillon dies and gauge. My question is...how much should i cam over? Also will this damage the press? Are all the dillon dies built like this or is this a spec issue?

    If i cam it over enough...the handle almost springs back a bit at the top of the stroke (when its full pressed down).

    Any tips and advice would be awesome!
  • #2
    kcstott
    I need a LIFE!!
    • Nov 2011
    • 11796

    no mention of rifle?? how many time brass has ben fired? is the brass mil surp?

    I load rifle rounds on my RL550B but i do not set it up to cam over I've never seen a need to do so. All my match ammo is loading on a RCBS Ammo master
    Last edited by kcstott; 09-01-2018, 6:00 AM.

    Comment

    • #3
      rsrocket1
      Veteran Member
      • Feb 2010
      • 2774

      Take a Sharpie and color the "sized" case completely. Chamber it and see where the ink rubs off. Now you can see and tell us where the case is "tight" in the chamber.

      For instance, if the brass was shot in a machine gun and the base is really expanded, the die may not reach all the way down and no amount of cam-over will size that part. If you didn't trim the neck and it stretched too far, again, no amount of screwing down the die will help.

      Comment

      • #4
        alexisjohnson
        Senior Member
        • May 2016
        • 651

        The rifle is a rem 700 5r and the brass is once fired (from a batch of remington match 168's i fired myself from the rifle)

        Comment

        • #5
          rsrocket1
          Veteran Member
          • Feb 2010
          • 2774

          More information is better. I assume the factory new loads chambered easily. Strange that only one shot in the same gun will stretch the brass to the point of making it tight even after a resizing.

          Comment

          • #6
            J-cat
            Calguns Addict
            • May 2005
            • 6626

            What lube? Did u lube the inside of neck? The right lube applied properly makes all the difference because the case will size easier.

            Comment

            • #7
              baih777
              CGN/CGSSA Contributor
              CGN Contributor
              • Jul 2011
              • 5680

              Over cam by going 1/16th of a turn. You feel a little resistance.
              When your brass will chamber with no resistance. Go for it.
              Checking your brass every time the tray fills up. I check 3 cases at random.
              It's easier with a Dillon case guage.
              Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
              I really miss the good old Pomona Gun Shows.
              I'm Back.

              Comment

              • #8
                smoothy8500
                Veteran Member
                • Sep 2009
                • 3846

                I didn't think progressives could "cam-over"? Granted, my experience with progressives is limited to RCBS and Hornady where you are supposed to leave a slight gap between sizing die and rotating shell-plate. Are Dillon progressives designed for an actual cam-over?

                Comment

                • #9
                  J-cat
                  Calguns Addict
                  • May 2005
                  • 6626

                  Progressives work best when the cases are already sized and primed.

                  Comment

                  • #10
                    popeye4
                    Senior Member
                    • Nov 2008
                    • 1534

                    Originally posted by J-cat
                    Progressives work best when the cases are already sized and primed.
                    Which kinda defeats the whole idea of a progressive, which is why I do all my bottleneck loading on a single stage. Rainy winter evenings are good for brass prep, then setting up a powder measure next to and bullet seater in the single stage makes things go as fast as the progressive can load.
                    sigpic
                    NRA Life Member
                    CRPA Life Member

                    Comment

                    • #11
                      smoothy8500
                      Veteran Member
                      • Sep 2009
                      • 3846

                      Originally posted by J-cat
                      Progressives work best when the cases are already sized and primed.
                      I tend to agree with this on rifle calibers. Pistol caliber the progressives work as expected.

                      The between the sizing force needed on bottleneck cases plus the potential for trimming just isn't worth the time shortcut.

                      Comment

                      • #12
                        Metal God
                        Senior Member
                        • Apr 2013
                        • 1839

                        This to me sounds like the age old press deflection . OP with all stations being used/operated size a case and leave the ram all the way up and look between the die and shell plate , is there a gap between them

                        I know this is not the same press but it does show my point



                        If so you still have room to screw your die down to size your case a little more .
                        Tolerate
                        allow the existence, occurrence, or practice of (something that one does not necessarily like or agree with) without interference.

                        Anyone else find it sad that those who preach tolerance CAN'T allow the existence, occurrence, or practice of (something that they do not necessarily like or agree with) without interference.

                        I write almost everything in a jovial manner regardless of content . If that's not how you took it please try again

                        Comment

                        • #13
                          mjmagee67
                          Veteran Member
                          • Jun 2011
                          • 2771

                          The 550 doesn't "cam over". My RCBS does. I set up my 550 so the resizing die just starts to push the shell plate down a few thousands of an inch.
                          If you want change you have to put in your 2 cents, you can't just sit on the sidelines and whine.

                          Comment

                          • #14
                            LynnJr
                            Calguns Addict
                            • Jan 2013
                            • 7959

                            The press used doesn't make any difference.
                            A press pushes the shellholder while holding the die.
                            As you start sizing brass your cases grow longer in length. That is why once fired brass is now snug. When you fire your brass it shrinks in length and the neck gets shorter.
                            As you keep sizing the brass by lowering the die the brass will stop getting longer as it has reached its maximum length. The brass will now chamber with even more tension.
                            If you screw the die down a 1/16 of a turn it will now make the neck longer bump the shoulder back and finish sizing the area right in front of the web area of your brass.
                            On match level brass the difference between great brass and junk is less than a quarter turn of the die.
                            In your case the die needs to go down a little more or the die needs to be sanded so it sizes more of the brass.
                            Try going lower in the press in baby increments while having your rifle sit in your lap. As the brass comes out drop it into the chamber and see if it fits. Stop going lower when it fits and mark the die.
                            As was mentioned progressive presses have built in slop by the nature of there mechanics.
                            If you can't lower the die enough and your bending/deflecting the shellplate that is the time when the die needs sanding.
                            In your case it sounds like the die needs more adjusting.
                            Most dies overly size the brass to compensate for all the possible chambers cut by all of the various manufacturers.
                            Last edited by LynnJr; 09-02-2018, 8:59 PM.
                            Lynn Dragoman, Jr.
                            Southwest Regional Director
                            Unlimited Range Shooters Association (URSA)
                            www.unlimitedrange.org
                            Not a commercial business.
                            URSA - Competition starts at 2000 yards!

                            Comment

                            • #15
                              jimmythebrain
                              Member
                              • Dec 2007
                              • 425

                              camming over is a thing that the press can or cannot do. Some presses like the Fortser C-Ax, Redding T-7 and Lee Classic Cast O press cannot cam over. There is a built in stop to ram travel.
                              Most modern presses have a hard stop in the ram travel that cannot be exceeded.
                              Older presses could cam over- the ram would raise to a max height and then would actually drop back down with additional movement of the handle.
                              Most presses get issues with press flex, and in a progressive presses this is magnified by 4-5 simultaneous steps (5 variable points of resistance-pressure)
                              Resizing adds a lot of resistance so if you separate this step your loads are more consistent in OAL
                              Also priming is the main failure point of a progressive press, so priming as a separate step also helps for consistent, correct primer seating.

                              If your press actually cams over then only your precision rifle cartridges will really benefit from trying to adjust for cam over. Running the shell holder up until it touches the die will usually provide consistent full length sizing. If you are using a neck sizing only die for a specific bolt action or single shot then the die does not thread down that far and a cam over press needs to be adjusted accordingly.

                              But I do not own a Dillon 550 to check if it cams over or has a hard stop built in.
                              Last edited by jimmythebrain; 09-02-2018, 10:42 AM.

                              Comment

                              Working...
                              UA-8071174-1