Unconfigured Ad Widget

Collapse

Troubleshooting Stuck Cases

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • djbooya
    Senior Member
    • Apr 2008
    • 816

    Troubleshooting Stuck Cases

    Equipment: Lee Loadmaster 9mm Setup (https://leeprecision.com/load-master-9mm-luger.html)

    I'm using the full length size carbide die in station 2 when I'm priming to also size the case.

    I'm getting more stuck cases recently like this:


    THe brass looks like this after I punch it out:




    I've run about 10k cases through the setup over the past few years.. Is this a sign of the die failing? I tried cleaning it about 500 rounds ago and didn't seem to help. Is it possible just the brass I'm using? It's all random range brass most only once fired. I don't remember getting these stuck cases much before. Now I'm getting them about 1 in 50.. it's a PITA to have to stop the flow to punch it out.

    Any ideas?

    Thanks!
    DJBooya
    "Try Not! Do or Do Not. There is no Try..."
    iTrader: https://www.calguns.net/forum/market...rader-feedback
  • #2
    kcheung2
    Veteran Member
    • Aug 2012
    • 4387

    Did you recently switch to wet tumbling?
    ---------------------
    "There is no "best." If there was, everyone here would own that one, and no other." - DSB

    Comment

    • #3
      Ironfether
      Junior Member
      • Aug 2013
      • 53

      Are you using the correct shell plate? Did you recently load .223 and forget to switch plates?

      Comment

      • #4
        someoneeasy
        Senior Member
        • Feb 2011
        • 2372

        A little lube helps.

        Comment

        • #5
          djbooya
          Senior Member
          • Apr 2008
          • 816

          I only reload 9mm.. and shell plate is the one that came with the press (9mm Loadmaster kit).

          I've used lube in the past (first thousand rounds or so), but I thought the purpose of the carbide dies was no lube needed?
          DJBooya
          "Try Not! Do or Do Not. There is no Try..."
          iTrader: https://www.calguns.net/forum/market...rader-feedback

          Comment

          • #6
            djbooya
            Senior Member
            • Apr 2008
            • 816

            Originally posted by kcheung2
            Did you recently switch to wet tumbling?
            no, dry tumble with walnut media
            DJBooya
            "Try Not! Do or Do Not. There is no Try..."
            iTrader: https://www.calguns.net/forum/market...rader-feedback

            Comment

            • #7
              checkenbach
              Senior Member
              • Nov 2008
              • 1469

              Get an undersized die! You’ll thank me later..

              Comment

              • #8
                Win231
                Senior Member
                • Sep 2015
                • 2099

                The 9mm is not exactly a straight-walled case; it's a little tapered. That's why a bit of lube on every 3rd or 4th case is a good idea. I put a bit of Redding sizing lube on my fingers while sizing 9mm. It works very well & lasts practically forever.
                Besides preventing stuck cases, you'll find it much easier to resize. I tumble after resizing/depriming. It removes all the lube & cleans cases at the same time.

                Comment

                • #9
                  NoHeavyHitter
                  Banned
                  • Jul 2011
                  • 2876

                  Before I run a batch of brass, I take an old T-shirt that I've lightly misted with WD-40 to remove tumbler dust and give a light film of lubrication.

                  I put all the shells in the T-shirt and pull the corners together and "massage" the brass in the T-shirt until it's thoroughly clean of tumbler residue.

                  Try this - you will be amazed at how much this decreases the effort required to operate the press. I've been doing it this way since I was taught back in 1981 and have never had any problem with the WD-40 causing issues. A very, very light film is all that's required.

                  Comment

                  • #10
                    bruce381
                    Senior Member
                    • Feb 2009
                    • 2454

                    glocked brass? what headstamp is that, are all the stuck ones the same headstamp?

                    Comment

                    • #11
                      someoneeasy
                      Senior Member
                      • Feb 2011
                      • 2372

                      Originally posted by djbooya
                      I only reload 9mm.. and shell plate is the one that came with the press (9mm Loadmaster kit).

                      I've used lube in the past (first thousand rounds or so), but I thought the purpose of the carbide dies was no lube needed?
                      With straight walled pistol brass, no lube is needed with carbide dies. 9mm is a little tapered and a little lube will help out a lot.

                      I load with a loadmaster as well and started out with 40s&w and had no issues without lube. Then I started loading 9mm and ripped out the rear lag bolt because there was so much resistance. Fixed this by using a longer lag bolt for the rear hole of the press and lubing my brass before loading. I just run them through the tumbler again after I finish loading.

                      Typically with carbide dies, no lube is needed, but if you're getting some resistance, a little lube goes a long way

                      Comment

                      • #12
                        3DGearGuy
                        Vendor/Retailer
                        • Jun 2012
                        • 804

                        Originally posted by djbooya
                        I only reload 9mm.. and shell plate is the one that came with the press (9mm Loadmaster kit).

                        I've used lube in the past (first thousand rounds or so), but I thought the purpose of the carbide dies was no lube needed?


                        You actually do need live for 9mm. Got that but if advice straight from Lee. Lube cases and everything should run much smoother. Very very little lube is needed, but is needed. Maybe a spray lube over the brass before running it through the press.


                        Sent from my iPhone using Tapatalk
                        3DGearGuy - 3D printing freedom since 2020! Use code CG10OFF for 10% off all orders of $15 or more!

                        Comment

                        • #13
                          djbooya
                          Senior Member
                          • Apr 2008
                          • 816

                          Originally posted by bruce381
                          glocked brass? what headstamp is that, are all the stuck ones the same headstamp?
                          stuck ones all different. not all glocks. This is range pickup brass from folks that are shooting Sigs, M&Ps, XDs, CZs, as well as Glocks.
                          DJBooya
                          "Try Not! Do or Do Not. There is no Try..."
                          iTrader: https://www.calguns.net/forum/market...rader-feedback

                          Comment

                          • #14
                            djbooya
                            Senior Member
                            • Apr 2008
                            • 816

                            Originally posted by someoneeasy
                            With straight walled pistol brass, no lube is needed with carbide dies. 9mm is a little tapered and a little lube will help out a lot.

                            I load with a loadmaster as well and started out with 40s&w and had no issues without lube. Then I started loading 9mm and ripped out the rear lag bolt because there was so much resistance. Fixed this by using a longer lag bolt for the rear hole of the press and lubing my brass before loading. I just run them through the tumbler again after I finish loading.

                            Typically with carbide dies, no lube is needed, but if you're getting some resistance, a little lube goes a long way
                            I ripped out that bolt 2 weeks ago.. sounds like a little lube will help fix up my issues based on the responses so far...
                            DJBooya
                            "Try Not! Do or Do Not. There is no Try..."
                            iTrader: https://www.calguns.net/forum/market...rader-feedback

                            Comment

                            • #15
                              djbooya
                              Senior Member
                              • Apr 2008
                              • 816

                              Originally posted by idlplumb
                              You actually do need live for 9mm. Got that but if advice straight from Lee. Lube cases and everything should run much smoother. Very very little lube is needed, but is needed. Maybe a spray lube over the brass before running it through the press.


                              Sent from my iPhone using Tapatalk
                              I do have spray lube that I've used before. Looks like that is the ticket that should resolve most of my issues..

                              --thanks for all the replies everyone.. good to know it's really just a simple fix...
                              DJBooya
                              "Try Not! Do or Do Not. There is no Try..."
                              iTrader: https://www.calguns.net/forum/market...rader-feedback

                              Comment

                              Working...
                              UA-8071174-1