Unconfigured Ad Widget

Collapse

.243 loads

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Gobijk
    Junior Member
    • Nov 2017
    • 7

    .243 loads

    I fire formed 20rnds of Hornady. Decided to try and work up some loads starting with a low powder load of Hodgdon Hornady Superformance. Never even close to max load. Heres what happened. Every oneof them stuck. Had to hit the bolt to extract them. Shot some factory ammo again no problems. No signs of excess pressure, nothing. All the brass measures fine...Any Ideas? One thought excess case lube?
  • #2
    NorCalFocus
    Veteran Member
    • Aug 2013
    • 3913

    How did you size them? Neck only? Were they hard to chamber compared to a factory round?

    Comment

    • #3
      mulyhuntr
      Senior Member
      • Jun 2013
      • 786

      Were you below min? Too low of powder charge can cause high pressure.

      Comment

      • #4
        NorCalFocus
        Veteran Member
        • Aug 2013
        • 3913

        Originally posted by mulyhuntr
        Were you below min? Too low of powder charge can cause high pressure.

        That's highly debatable. I'll bet a dollar to a donut hole this has a one in a billion chance of happening.

        Comment

        • #5
          Gobijk
          Junior Member
          • Nov 2017
          • 7

          Neck size only. Chambering was normal. Charges were all above normal . But nowhere near max. Kind of a puzzler. Asked the guy at my supply shop. He has no idea either..

          Comment

          • #6
            WMG
            Senior Member
            • Jul 2016
            • 1159

            Originally posted by Gobijk
            Neck size only. Chambering was normal. Charges were all above normal . But nowhere near max. Kind of a puzzler. Asked the guy at my supply shop. He has no idea either..
            Bump your shoulder back a smidge .... should fix it I would imagine
            If you start thinking like a Free Man
            You'll begin to feel like a Free Man
            And pretty soon you'll begin acting like a Free Man

            Comment

            • #7
              NorCalFocus
              Veteran Member
              • Aug 2013
              • 3913

              Originally posted by Gobijk
              Neck size only. Chambering was normal. Charges were all above normal . But nowhere near max. Kind of a puzzler. Asked the guy at my supply shop. He has no idea either..
              Stop neck only sizing. If you want to mandrel size your necks then body size your brass you can do that. However you can FL size both in one step.

              I know everyone thinks neck only sizing is more consistent. When you neck only size, your brass is growing every single firing. At some point it will get to big for your chamber and your going to need to body size it. With FL sizing your setting your brass back to the same spec every single time. That is way more consistent. If you don't have a case comparator, get one. Then measure your set back. You want to bump the shoulders back .001-.003" each time.

              If you need to buy a FL die, I really like Forster dies. Their expander ball sits higher up, so the neck is resized while the case is centered in the die.

              Comment

              • #8
                divingin
                Veteran Member
                • Jul 2015
                • 2522

                Does a piece of fired brass chamber easily? If not, there's a need to size at least part of the case (more so than just the neck.) Light loads can stretch more due to not enough case expansion to hold the case to the chamber wall (case jams against the bolt head, and the shoulder still blows forward.) That may also be part of the problem. Measure case base to datum between fired and unfired to compare.

                Had a similar problem with once-fired Lake City brass. Chambering was just a tad tougher than factory new ammo, but would not extract at all using the bolt (a cleaning rod tapping the case knocked it free.) FL resizing the brass once took care of it. Apparently, the "sized to SAAMI specs" done by the supplier was actually not done.

                If you suspect it's case lube, it's easy enough to wipe the stuff off before chambering. Should be easy enough to prove or disprove.

                Comment

                • #9
                  JackEllis
                  Veteran Member
                  • Nov 2015
                  • 2731

                  I had a similar problem with both once-fired cases and what appears to be factory ammo that used once-fired cases. They would not chamber. Period. I now FL size everything.

                  Comment

                  • #10
                    superdave50
                    Senior Member
                    • Feb 2017
                    • 813

                    +1 Forster fl dies

                    Comment

                    • #11
                      Gobijk
                      Junior Member
                      • Nov 2017
                      • 7

                      All sounds good. Probably going to shoot next week see what happens. Im going to test some .300 blk out, new .44mag and some .300 mag. Just wish I didnt have to drive out to Hodge road. I really dont like going to other ranges. Like to do my own thing.
                      Thanks for all the input.

                      Comment

                      Working...
                      UA-8071174-1