Unconfigured Ad Widget

Collapse

.223 case length

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • cleanguy46
    Senior Member
    • Mar 2008
    • 1050

    .223 case length

    I am getting started preping some .223 brass and am at the stage to where I need to check case length and trim as needed. After reading the specs in the RCBS/ Speer reloading manual it says to trim casing to 1.750". The maximum case length stated is 1.760". I have been trimming some and its falling in the area of 1.751" to 1.753". I think this is good to go however I have found a few casings that are below 1.750". What is the minimum length of a case that needs to be taken out of service and not reloaded? Thanks for the help!
    sigpicWango Tango!
  • #2
    USN CHIEF
    I need a LIFE!!
    • Nov 2007
    • 11540

    Don't really know what the minimum length is but I have reloaded and shot some that were 1.725 without a problem.
    Originally posted by tankerman
    I think most folks bubba their AR's because they watch too many action movies, play too many video games and don't understand how to socialize properly, so they fantasize about being 'action hero's'. Kind of like little girls playing dress-up.
    Originally posted by Douglas711
    Is everybody stocking up on guys now? Just curious some gun prices seem to be getting high.

    Comment

    • #3
      brian01tj
      Member
      • Mar 2006
      • 468

      Are they measuring below 1.750 before or after trimming? If you use a quality trimmer your length shouldnt fluctuate more than .001 to .002. First I would question the brand of brass you are using. And second, have you full length or neck sized it yet. Once you do either of those the case length will be increased. And to answer your main question....I personally wouldn't chance anything below 1.748.

      http://www.socalprecision.com/


      Didn't get your question answered here? Check out our forum to discuss your precision rifle... http://www.socalprecisionforum.com/

      Comment

      • #4
        USN CHIEF
        I need a LIFE!!
        • Nov 2007
        • 11540

        Originally posted by brian01tj
        And to answer your main question....I personally wouldn't chance anything below 1.748.
        WHY? Please explain your reasoning or are you just coming up with that magical number?
        Originally posted by tankerman
        I think most folks bubba their AR's because they watch too many action movies, play too many video games and don't understand how to socialize properly, so they fantasize about being 'action hero's'. Kind of like little girls playing dress-up.
        Originally posted by Douglas711
        Is everybody stocking up on guys now? Just curious some gun prices seem to be getting high.

        Comment

        • #5
          Beelzy
          Calguns Addict
          • Apr 2008
          • 9225

          Some cases are known to be "shortys". I separate those as best for loads
          that push the envelope as they don't "grow" so fast.

          I generally just kepp the lot fof cases floating in the 1.750-1.750 range and
          don't worry about trimming until most of the cases start getting to the max
          length. OR, when I start seeing those rogue 1.755 cases.

          Give the brass its chance to grow a little before trimming, it works the brass
          and can lead to bullet seating issues or split case necks prematurely.

          As far as when to ditch the brass, I usually discard after I can't read the headstamp
          anymore.
          Last edited by Beelzy; 02-23-2009, 11:09 AM.
          "I kill things for a living, don't make yourself one of them"

          Comment

          • #6
            cleanguy46
            Senior Member
            • Mar 2008
            • 1050

            Originally posted by brian01tj
            Are they measuring below 1.750 before or after trimming? If you use a quality trimmer your length shouldnt fluctuate more than .001 to .002. First I would question the brand of brass you are using. And second, have you full length or neck sized it yet. Once you do either of those the case length will be increased. And to answer your main question....I personally wouldn't chance anything below 1.748.
            First of all almost all of the brass is falling above the 1.750 length. I have a few stragglers that are below that number. Most all is once fires LC brass so I definitely dont have a brass problem. I have been checking mesurements before trimming and trim to between 1.750 to 1.755. I'm not a match shooter so all I want is some decent rounds to shoot with. If I do in the future then I will be a little more picky on the numbers. The numbers that I am concerned with is the minimum length.
            Last edited by cleanguy46; 02-23-2009, 11:10 AM.
            sigpicWango Tango!

            Comment

            • #7
              eaglemike
              CGN/CGSSA Contributor - Lifetime
              CGN Contributor - Lifetime
              • Jan 2008
              • 4002

              Ummmmm, short brass (within reason) is almost never a problem. It just hasn't been stretched enough yet. Right on, Chief. A mere .002 under I wouldn't even think about that one. If I was shooting B/R for ultimate groups.....

              BTW, has anyone ever seen .45acp brass that needed trimming? Yes, I know it's a straight walled rimless case.

              all the best,
              Mike
              There are some people that it's just not worth engaging.

              It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

              Comment

              • #8
                Beelzy
                Calguns Addict
                • Apr 2008
                • 9225

                I never seem to need to trim the pistol cases at all. .380 thru the 500mag.
                "I kill things for a living, don't make yourself one of them"

                Comment

                • #9
                  Rule .308
                  Veteran Member
                  • Oct 2005
                  • 2531

                  Same here, although the bulk of my pistol reloading is all for run of the mill stuff, 38/357, 9mm, 40, and 45, I have yet to run into one that required trimming.

                  Comment

                  • #10
                    Desertfox
                    Junior Member
                    • Nov 2008
                    • 59

                    Originally posted by cleanguy46
                    I am getting started preping some .223 brass and am at the stage to where I need to check case length and trim as needed. After reading the specs in the RCBS/ Speer reloading manual it says to trim casing to 1.750". The maximum case length stated is 1.760". I have been trimming some and its falling in the area of 1.751" to 1.753". I think this is good to go however I have found a few casings that are below 1.750". What is the minimum length of a case that needs to be taken out of service and not reloaded? Thanks for the help!
                    Use the LEE case trimmer (case length gauge and the cutter with lock stud) cheapest and easiest way.

                    Comment

                    • #11
                      cleanguy46
                      Senior Member
                      • Mar 2008
                      • 1050

                      Originally posted by Desertfox
                      Use the LEE case trimmer (case length gauge and the cutter with lock stud) cheapest and easiest way.
                      I already have a Lyman universal case trimmer and it works great. Thanks for the heads up tho.
                      sigpicWango Tango!

                      Comment

                      • #12
                        joemama
                        Senior Member
                        • Aug 2008
                        • 2333

                        I'm not a fan of that lee case trimmer. I just trimmed my first 118 rounds with that and one of those straight battery powered screw drivers. My fingers hurt pretty bad from using it. I think I'm gonna invest in another trimmer for when I get more brass to trim. The one good thing was they were all uniform when I was done.

                        Comment

                        • #13
                          mecam
                          Veteran Member
                          • Jun 2007
                          • 4049

                          Originally posted by eaglemike
                          BTW, has anyone ever seen .45acp brass that needed trimming? Yes, I know it's a straight walled rimless case.
                          I've reloaded a .45ACP brass in 3 cycles and still fits perfectly in my gage.

                          Just pay attention to overly used brass. This is supposedly MiWall's once fired reloads.

                          sigpic

                          Comment

                          • #14
                            eaglemike
                            CGN/CGSSA Contributor - Lifetime
                            CGN Contributor - Lifetime
                            • Jan 2008
                            • 4002

                            Originally posted by mecam
                            I've reloaded a .45ACP brass in 3 cycles and still fits perfectly in my gage.

                            Just pay attention to overly used brass. This is supposedly MiWall's once fired reloads.

                            I don't have the right emoticon for that situation! Not really surpised, as Q.C. has generally gone in the toilet for a lot of things these days.

                            I measured .45 cases many times long ago, and compared them to chamber drawings. Most .45 acp brass won't ever headspace properly, since it's so short. This is often true even in a match chamber. If you want to great shooting 1911, fit the barrel, then ream the chamber to match a batch of brass. It really does make a difference. I've even tested 625's w/o moonclips, and the were more accurate than when shot with (brand new and flat) moonclips.

                            Bottlenecked rifle stuff that headspaces on the shoulder like the .223/.556 will not likely cause a problem due to being a short case IMHO. If it was trimmed crazy short, who knows? More likely to be size too much, and the shoulder set back. Seen this one once or maybe even 3X before. Did it once many years ago myself, and then got to watch others do it.... Did I mention I've made a mistake or 2?

                            all the best,
                            Mike
                            Old machine shop saying "the guy that never made a mistake never made stuff"
                            There are some people that it's just not worth engaging.

                            It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

                            Comment

                            • #15
                              brian01tj
                              Member
                              • Mar 2006
                              • 468

                              Originally posted by USN CHIEF
                              WHY? Please explain your reasoning or are you just coming up with that magical number?
                              It's honestly just the magical number. I should have asked him if its a plinking round he's whipping up or for accuracy. Ill put most anything through my AR but off the bench with my bolt gun its nothing below 1.748.

                              http://www.socalprecision.com/


                              Didn't get your question answered here? Check out our forum to discuss your precision rifle... http://www.socalprecisionforum.com/

                              Comment

                              Working...
                              UA-8071174-1