Unconfigured Ad Widget

Collapse

Experience with Barnes TSX bullets?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • alexisjohnson
    Senior Member
    • May 2016
    • 651

    Experience with Barnes TSX bullets?

    Hey guys,
    I'm wondering what experiences you all have had with the Barnes all copper TSX bullets.

    I shot some rounds out of my LMT Ar and they grouped less than 1 MOA.

    Is this consistent with what you've experienced or did i get a supernatural batch?
  • #2
    nedro
    Veteran Member
    • Nov 2014
    • 4130

    I had mixed results.
    My first set of loads made me want to throw the rest away.
    So I just loaded them up, just to shoot out my supply and caught a good recipe. Sub MOA.
    This was for a 6.8 SPC. I still think they are too expensive for me to buy again. There are many better bullets for the 6.8.

    Comment

    • #3
      pacrat
      I need a LIFE!!
      • May 2014
      • 10287

      I've used the TSX in my .270 exclusively for hunting since the "Buzzard Proof" requirement. Same diameter different weight than 6.8. With a lot more steam behind it.

      Excellent performance on game. And sub MOA accuracy after working loads a bit.

      JM2c

      Comment

      • #4
        MJB
        CGSSA Associate
        • Sep 2010
        • 5925

        Most accurate bullet I've shot.......all my shots will touch each other

        I use magnum primer even in my 270, get to max load once you see pressure signs back down 1/2 a grain or two then back off the lands .04-.05.
        One life so don't blow it......Always die with your boots on!

        Comment

        • #5
          Whiterabbit
          Calguns Addict
          • Oct 2010
          • 7602

          fine bullets. Just expensive.

          Comment

          • #6
            kblack583
            Senior Member
            • Apr 2008
            • 704

            Great bullet. Accurate out of my 6.8 and great hunting bullet.

            Comment

            • #7
              rick1085
              Member
              • Feb 2013
              • 138

              Load them fast. Seat them deep.
              In my experience their are many better choices in lead.
              But, not for California hunting.

              I've gotten 1 moa or a little bit better in all my hunting rifles but
              It took considerable effort. All Barnes tsx or ttsx seem to be very sensitive to minor changes in velocity and seating depth.
              Most importantly, start with a super clean bore. (NO LEAD)

              Comment

              • #8
                JackEllis
                Veteran Member
                • Nov 2015
                • 2731

                Most importantly, start with a super clean bore. (NO LEAD)
                Also make sure you get rid of any copper. I could have saved myself a lot of grief if I'd used both a lead/powder solvent and a copper solvent in my big game rifle from the getgo.

                Comment

                • #9
                  stevec223
                  Senior Member
                  • Jul 2011
                  • 1620

                  I have had sub-moa with the TSX and TTSX in 243,, 243wssm,, 30-06 and 300 Win mag.. And nosler e-tip in 308.... Near max loads and book col seems to work with the most accurate powder listed in the Barnes book for me.. I saw the light 10 years ago ,,, in just knowing that stupid kali was going to ban lead bullets statewide... . And started loading non-lead for hunting... Glad I did.... Cheers..

                  Comment

                  • #10
                    RegionRat
                    Junior Member
                    • May 2017
                    • 61

                    I agree on several points.
                    The seating depth tends to end up deep in my rigs. I stopped doubting what the targets were telling me and I ended up seating deeper till the groups closed up.
                    Also, the need to start with a very clean bbl and then not flip back and forth between these and other types. The mixed use tends to foul the bbl much faster than keeping them separated.
                    These have matched the performance of my best standard bullet results. In my opinion, I have no gripes about the bullets at all and can see how they would be better balanced.
                    My only gripe is that I a being forced to run them due to bogus legislation.

                    So clean up very well before you start working up the load, and don't hesitate to seat deep if they is where they lead you. Good Luck and Good Hunting.

                    Comment

                    • #11
                      HBDano
                      Junior Member
                      • Feb 2015
                      • 41

                      I have had good experience with both TSX and TTSX projectiles from Barnes. I shoot the 100gr TTSX almost exclusively from my 6.5 Grendel's when coyote hunting, and the 120's perform well also.

                      Barnes recommends to start seating at .050" off the lands, and that best accuracy will be found between 0.030"-0.070 off the lands. Being that the projectiles are designed to be accurate with somewhat sizeable jump is at least one of the reasons they seam to magically be accurate from an AR when loaded to magazine length.

                      My only problem with them is that I found some inconsistency between lots... Enough to effect accuracy... So now I measure all the projectiles before loading them and will separate them based on size and weight differences.

                      Sent from my Nexus 5X using Tapatalk

                      Comment

                      • #12
                        jjjjeremy
                        Member
                        • Apr 2012
                        • 148

                        Definitely effective, sub MOA with stock ammo in my W70

                        Comment

                        • #13
                          kube6
                          Junior Member
                          • Aug 2010
                          • 10

                          Bullet weight (overall length) and barrel twist have to be in agreement for bullet stabilization.

                          Comment

                          Working...
                          UA-8071174-1