Unconfigured Ad Widget

Collapse

Question about loading .223 in volume

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pennys dad
    Arizona Ex-Pat
    CGN Contributor - Lifetime
    • Feb 2008
    • 5984

    Question about loading .223 in volume

    Hey

    Gotta question.

    So what do you'all use to load your 223 in volume. Not commercial volume, but maybe 1000 rounds a month? I currently load .357 and will soon move into .308 and .45. I figure my time will start to run thin loading .357, .45 and .308 so Im looking for a solution for .223 volume loading.

    Thx
    Pennys Dad

    Ps 25:4-5 NLT Show me the right path, O Lord; point out the road for me to follow. Lead me by your truth and teach me, for you are the God who saves me. All day long I put my hope in you.
  • #2
    Darklyte27
    Calguns Addict
    • May 2008
    • 9372

    First off what is your problem? There has to be a problem before we can supply a solution

    Do you have all the .223 hardware already? Or are you just asking for load data?

    So far, my knowledge is this

    Powder Winchester 748, Hodgdon 335, varget, tac ramshot, reloader 10/15
    Primers cci # 400, or #41 military primers
    usually 55 gr bullets for plinking.
    and you supply your brass
    Last edited by Darklyte27; 02-13-2009, 10:31 PM.
    2 HANDGUNS STOLEN! 1 RECOVERED READ HERE

    Chickens

    Want to get into Ham Radio? Click here
    http://www.calguns.net/calgunforum/s...d.php?t=202581

    Comment

    • #3
      TEX1966
      Member
      • Mar 2006
      • 255

      .223 brass from www.tjconevera.com. or stuff I already have.
      62 gr. bullets from Golden West Brass.
      CCI 400 small rifle primers.
      IMR 4895 or AA# 2230. I prefer the AA#2230 as it meters great in my Dillon and the IMR 4895 seems to sometime stick in the measure. Thank god for the Dillon powder check system as I would have had several under / over / squib loads from the IMR and had powder all over the bench for the 5,000 rounds I loaded with it. Using the AA# 2230 it meters as set with no deveation and little or no wasted powder.
      Hope this helps, Tex

      Comment

      • #4
        CSACANNONEER
        CGN/CGSSA Contributor - Lifetime
        CGN Contributor - Lifetime
        • Dec 2006
        • 44094

        I use a Dillon 550, a Dillon Swager and a Giraurd trimmer.
        NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
        California DOJ Certified Fingerprint Roller
        Ventura County approved CCW Instructor
        Utah CCW Instructor


        Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

        sigpic
        CCW SAFE MEMBERSHIPS HERE

        KM6WLV

        Comment

        • #5
          TMC
          Senior Member
          • Oct 2005
          • 2348

          Volume for 223 is a two stage deal. Spend a loading session decapping, sizing and trimming all of the your brass, assuming you have less 1,000 pieces. If you have more you'll need to spread it out over a few session unless your Superman (it took me about 6 hours over a few nights to prep a 5 gallon bucket full, around 5,000)

          Next a good run through the polisher to remove the sharp edges and case lube.

          Then start loading. With the prep done the press runs easier without sizing and the powder drops better into dry cases.

          You can't rush rifle loading, it takes time for 25+ grains of powder to get through that small case neck unlike pistol cases where you dropping less than 8 grains into and huge hole.
          where are my pistol mags?

          Comment

          • #6
            TEX1966
            Member
            • Mar 2006
            • 255

            Good point jrascon. Prep takes a lot of time. I tumble the brass for 2 hrs in walnut with polish and then 2 hrs in corn cob to clean it. I then run it through (after lube with Dillon case lube) the Dillon resizer / trimmer to get it to min COL and an RCBS sizer die to resize the neck on my XL/650. I then tumble to remove the lube and chamfer and clean the brass on a RCBS Case Prep center. I hand prime on the RCBS hand priming tool. This may seem like a lot of extra steps but I like to inspect each piece of brass as it is easier to trash a $.003 piece of brass than a registered "California AR Reciever" blowing up or damaged by a bad load.

            Comment

            • #7
              ar15barrels
              I need a LIFE!!
              • Jan 2006
              • 57202



              I use the 650 for decapping, sizing and trimming.
              I use the 1050 on the right for priming, charging and seating.
              Randall Rausch

              AR work: www.ar15barrels.com
              Handguns: www.handgunbarrels.com
              Bolt actions: www.700barrels.com
              Foreign Semi Autos: www.akbarrels.com
              Most work done while you wait on a scheduled shop visit.

              Comment

              • #8
                Rule .308
                Veteran Member
                • Oct 2005
                • 2531

                I use something similar to what Randall has only I do it all on my 550. The real time saver here is the Dillon electric trimmer/sizer set up combined with the RCBS lube/decap die. You lube it and decap it in one station and then the trimmer has a sizer die on it too so that it runs the brass up into the sizer and anything that sticks out is zipped off with the spinning carbide bit. It trims it so flush and square to the case that there is litterally no burr left over. The trimmings are sucked away by the vacuumm cleaner attachment.

                The other big time saver that Randall has going is in that big dollar 1050, among other things it has a station in it that re-swages the primer pockets on military brass.

                With a setup like this all a guy has to do is run his brass through the 550, through the tumbler to get the lube off of it, and then through the 1050 and it is done. Something Randall pointed out to me once is that if you can get your press set up so that you need not take your hand off of the press handle you can really crank out the brass. This means you will need auto case loading so that you set a bullet on the case mouth and pull the handle, it is when you have to load a case, load a bullet, grab the handle and pull that you get slowed down. Your next big boat anchor is feeding that beast primers, I think Randall was saying it is about 3 minutes for the Dillon primer tube loader to load one tube and his best time loading 100 rounds through that 1050 is still just over 3 minutes.

                So, how fast do you want to go? Just off the top of my head I would say that you would be north of 2.5 grand somewhere to be as fast as Randall: RL550B, RL1050, electric case trimmer, primer tube filler, miscellaneous dies and hardware, etc.

                You could do it for less money if you bought a 650 with the case loader, the case trimmer, and the primer tube filler. With this set up you will still need to process your brass through the sizing/trimming set up and then have to individually address the primer pockets on each piece of brass and then you can run it through the 650 to prime, charge, seat, and crimp and not pull your hand off of the press handle. Obviously you will have to change the set ups on your 650 from size/ trim to charge/seat but that is no biggy.

                Comment

                • #9
                  pennys dad
                  Arizona Ex-Pat
                  CGN Contributor - Lifetime
                  • Feb 2008
                  • 5984

                  Yikes sorry forgot the problem

                  My wife and daughter shot 223 like its pez candy and my single stage press cant keep up, so i need volume loading.
                  Pennys Dad

                  Ps 25:4-5 NLT Show me the right path, O Lord; point out the road for me to follow. Lead me by your truth and teach me, for you are the God who saves me. All day long I put my hope in you.

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    Originally posted by jrascon
                    Yikes sorry forgot the problem

                    My wife and daughter shot 223 like its pez candy and my single stage press cant keep up, so i need volume loading.
                    Your a lucky man. I wish I could say that!
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      fairfaxjim
                      Senior Member
                      • Apr 2006
                      • 2146

                      Originally posted by jrascon
                      Yikes sorry forgot the problem

                      My wife and daughter shot 223 like its pez candy and my single stage press cant keep up, so i need volume loading.
                      Couple of choices -

                      Blue Kool Aid (Dillon RL550B or XL650 depending on volume of other cartidges you want to load)

                      Red Dye (Hornady Lock-N-Load AP. Initial entry price around (lower than with the bullet rebate) the Dillon 550, features that approach the 650.)

                      Either way you're hooked!
                      "As soon as we burn 'em," Chinn said, "more come in."
                      Ignatius Chinn, a FORMER veteran firearms agent.
                      CONTRA COSTA TIMES 03/04/2008

                      "please guys please no ridiculous offers....Im a girl, not an idiot" Mistisa242

                      Comment

                      • #12
                        ar15barrels
                        I need a LIFE!!
                        • Jan 2006
                        • 57202

                        Originally posted by Rule .308
                        So, how fast do you want to go? Just off the top of my head I would say that you would be north of 2.5 grand somewhere to be as fast as Randall: RL550B, RL1050, electric case trimmer, primer tube filler, miscellaneous dies and hardware, etc.
                        You would need a 650 for processing brass like I do as the 550 casefeeder will not do rifle cartridges.
                        Randall Rausch

                        AR work: www.ar15barrels.com
                        Handguns: www.handgunbarrels.com
                        Bolt actions: www.700barrels.com
                        Foreign Semi Autos: www.akbarrels.com
                        Most work done while you wait on a scheduled shop visit.

                        Comment

                        • #13
                          smokingloon
                          Senior Member
                          • Mar 2008
                          • 1012

                          If you go the Hornady route, their shell plates are back ordered untill march 23 from midway. So I have this new progressive press just sitting here while I'm still using my single stage.

                          Comment

                          • #14
                            ar15barrels
                            I need a LIFE!!
                            • Jan 2006
                            • 57202

                            Originally posted by smokingloon
                            If you go the Hornady route, their shell plates are back ordered untill march 23 from midway. So I have this new progressive press just sitting here while I'm still using my single stage.
                            I have dillon 550 and 650 shellplates if you need to borrow one...
                            Randall Rausch

                            AR work: www.ar15barrels.com
                            Handguns: www.handgunbarrels.com
                            Bolt actions: www.700barrels.com
                            Foreign Semi Autos: www.akbarrels.com
                            Most work done while you wait on a scheduled shop visit.

                            Comment

                            • #15
                              CSACANNONEER
                              CGN/CGSSA Contributor - Lifetime
                              CGN Contributor - Lifetime
                              • Dec 2006
                              • 44094

                              You should have drank the BLUE coolaid!
                              NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                              California DOJ Certified Fingerprint Roller
                              Ventura County approved CCW Instructor
                              Utah CCW Instructor


                              Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                              sigpic
                              CCW SAFE MEMBERSHIPS HERE

                              KM6WLV

                              Comment

                              Working...
                              UA-8071174-1