Hi guys, Im looking to see the steps you take while casting your own bullets. I just started by making ingots. If you want to share please include the way you melt and all materials used. This is so much fun I wish I started sooner.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
How do you cast?
Collapse
X
-
How do you cast?
FOR SALE: XD45, 24/47 Yugo Mauser, AK RPD AES-10bTags: None -
Not again. i just did a write up for it on thr here is the link.
sigpic -
-
Thanks for the link and the write up at THR. I've been reading a lot over at Cast Boolits for the last month or two and recently ordered my casting equipment.Not again. i just did a write up for it on thr here is the link.
http://www.thehighroad.org/showthread.php?t=421223
I'm hoping to find time for casting .358's this weekend and your instructions shed some more light on the process.
We'll see how it goes.Comment
-
my kit consists of
coleman 425e stove
6 inch cast skillet (it holds about 10 pounds of melt)
plunger handle(to whack the sprew plate of the mold and tap the fulcrum to release the bullets)
tablespoon (to pour the lead into the mold)
1 gallon coleman fuel (to make stove work)
1 wand lighter (to light coleman stove and to smoke the mold cavities till they ar black)
1 aluminum rod(to stir the melt)
1 bucket of water to drop the bullets into(it cools them quick and no deformation)

i used the lee 2 cavity molds
and lee sizing dies a .356 and a .452
its pretty fun i just made 450 more 9mm boolits yesterday ,sized them ,tumble lubed with lee liquid alox and the alox has dried today so i boxed them upComment
-
I understand this also helps harden the finished bullets. Do you have a hardness tester and / or have you tested any of your castings to see how air cooled compare to water dropped... sized vs. un-sized?
It looks like you've got the same .452 mold I've got in transit from Natchez (I ordered the 6 cavity)Originally posted by bohokii used the lee 2 cavity molds
Do you NEED to size? I've heard tell that this mold drops well enough to shoot after casting / lubing (I too plan to try LLA to start). I've got sizing dies in transit, but I'm interested to hear if you've tried shooting these bullets without sizing.Originally posted by bohokiand lee sizing dies a .356 and a .452
its pretty fun i just made 450 more 9mm boolits yesterday ,sized them ,tumble lubed with lee liquid alox and the alox has dried today so i boxed them up
Also, what are you shooting these out of? I hear lots of rumors (from Glock and others) that I shouldn't shoot lead out of my Glock 21. I have read many other posts that say the .45 Glock barrels normally do very well with lead bullets (much better than say the .40's), so long as you keep the pressures reasonable and the bullet profile feeds well. Just wondering if you can weigh in on that from personal experience.Comment
-
I dont think we discuss it enough here. I just did my first batch today, Mine look like bright silver. Really beautiful. So far I have a FP 230 gr mold from LEE I thought I was getting RN, but o'well. Using a coleman stove and roofing leed. Im just dropping onto a towel, after realizing I was melting a carpet.FOR SALE: XD45, 24/47 Yugo Mauser, AK RPD AES-10bComment
-
i dont believe water quenching has any hardening effect i do not check my hardness i make my bullets out of ex-bullets mostly 22 fragments and i load them light
3.5 bulls for 9 4.0 for 45
they say they can be shot without sizing butIt looks like you've got the same .452 mold I've got in transit from Natchez (I ordered the 6 cavity)
Do you NEED to size? I've heard tell that this mold drops well enough to shoot after casting / lubing (I too plan to try LLA to start). I've got sizing dies in transit, but I'm interested to hear if you've tried shooting these bullets without sizing.
i size anyway cause i like all of them consistant and perfectly round
besides the sizing kits were only $12 and they came with the alox lube
i dont like the 6 cavity cause the sprue plate is aluminum and sometimes i am a little lax with my mold and let it cool too much and have to really whack it to cut the sprue
you should whack the sprue off as soon as it cools on the top it kinda gets a little sunk-in look then i knock the sprue back in the melt to become future bullets
i fire these out of my glock21 using a fed ord barrel(shame they got shut down) and a baby eagle with a eaa witness barrelAlso, what are you shooting these out of? I hear lots of rumors (from Glock and others) that I shouldn't shoot lead out of my Glock 21. I have read many other posts that say the .45 Glock barrels normally do very well with lead bullets (much better than say the .40's), so long as you keep the pressures reasonable and the bullet profile feeds well. Just wondering if you can weigh in on that from personal experience.
naked lead wont touch my polygonal rifling heck i wont even shoot those plated tmj ones
i shoot the 9mm out of a norinco tokarev and egypt helwan
(they are both kind of expendable so if they get too bad they are getting thrown in the bay) i wish i could get a lone wolf or other stainless barrel for my g17 but i dont want to pay $100 maybe i'll run into one used for $75
here are some ready to roll

if you check the 3rd 45 you can see a little mold line where the mold didnt close quite right but the sizer makes it usable
these things just have to fly straight for about 30 yards anyway
ps the lee liquid alox makes a bit of smoke maybe i'm putting it on to heavyLast edited by bohoki; 01-20-2009, 10:26 PM.Comment
-
That's what I've been reading.
From what I understand, it's a window of hardness you're looking for... to soft is bad, too hard is bad - either can/will cause excessive leading. Granted, it sounds like it's a big window for .45 ACP.
Now I'm trying to figure out what will be right for me. I figure to try air cooled first, then water dropped.
I guess I'll be checking the barrel every 10 rounds to start - fortunately, pulling the barrel is easy on a Glock. Any tips on what to look for in excessive leading? I figured that if the bore starts getting dark or nasty, that'll be my indicator.
DwarfComment
-
I see casting threads here now and again, but agree it's not very common at CG.net. Have you checked out Cast Boolits (linked above by .454). I've seen a number of Cal Gunners there.I dont think we discuss it enough here. I just did my first batch today, Mine look like bright silver. Really beautiful. So far I have a FP 230 gr mold from LEE I thought I was getting RN, but o'well. Using a coleman stove and roofing leed. Im just dropping onto a towel, after realizing I was melting a carpet.
CB.com is a wealth of great information on casting (as you might suspect from the name). Sections dedicated to casting, equipment, reloading, using cast in different gun types, etc... If not for that site, I'd still be on the fence about buying into this game.
Everyone there is quite helpful in answering newbie questions if you've got them, but I've found most of my answers using the search function.Comment
-
please dont fire lead down a oem glock barrelThat's what I've been reading.
From what I understand, it's a window of hardness you're looking for... to soft is bad, too hard is bad - either can/will cause excessive leading. Granted, it sounds like it's a big window for .45 ACP.
Now I'm trying to figure out what will be right for me. I figure to try air cooled first, then water dropped.
I guess I'll be checking the barrel every 10 rounds to start - fortunately, pulling the barrel is easy on a Glock. Any tips on what to look for in excessive leading? I figured that if the bore starts getting dark or nasty, that'll be my indicator.
Dwarf
you are just going to have to trust me on that oneComment
-
Between my pops and I, we've done 10's of thousands of cast bullets through 4 9mm glocks, all with OEM barrels. Theres a trick to it, some trial and error required, but its not hard to get virtually no leading. Proper alloy, sizing, and lubing is all that is needed.
Getting an aftermarket barrel makes it easy to shoot whatever junk lead you want through them, however.GAP Team Shooter 5Comment
-
If you're getting excessive leading, the barrel will look like you shot a silver crayon through it. Normally, you'll see little gray streaks and that is acceptable. But you don't want much more than that. Using a quenched wheelweight alloy, sized appropriately, using a powder like unique (or something in that burn rate), keeping velocities to under 800, you shouldn't have an issue. I used a 225 RN in my Glock 30 all the time. I sized/lubed conventionally and then added a coat of allox. Not much lead to speak of.That's what I've been reading.
From what I understand, it's a window of hardness you're looking for... to soft is bad, too hard is bad - either can/will cause excessive leading. Granted, it sounds like it's a big window for .45 ACP.
Now I'm trying to figure out what will be right for me. I figure to try air cooled first, then water dropped.
I guess I'll be checking the barrel every 10 rounds to start - fortunately, pulling the barrel is easy on a Glock. Any tips on what to look for in excessive leading? I figured that if the bore starts getting dark or nasty, that'll be my indicator.
DwarfGAP Team Shooter 5Comment
-
There's an interesting discussion of that topic here:
Comment
Calguns.net Statistics
Collapse
Topics: 1,870,994
Posts: 25,178,306
Members: 358,862
Active Members: 5,382
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 32488 users online. 122 members and 32366 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment