Unconfigured Ad Widget

Collapse

WFT 308 repeatability?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mike_w
    Junior Member
    • Jan 2008
    • 37

    WFT 308 repeatability?

    So I have a bunch of Lake City once fired brass that has been full length resize. When trimming I'm getting variations of .0 09 +/- , is there any hope to get the case length any closer. What are the effects of having the case lengths too short?
  • #2
    pacrat
    I need a LIFE!!
    • May 2014
    • 10287

    Originally posted by mike_w
    So I have a bunch of Lake City once fired brass that has been full length resize. When trimming I'm getting variations of .0 09 +/- , is there any hope to get the case length any closer. What are the effects of having the case lengths too short?
    More info needed as to cause of variation. What type trimmer are you using? Lathe type that indexes off the base? Or one that indexes off the shoulder?

    If the former, and still getting variations that big. You technique is likely at fault.

    If the latter, that is to be expected until the cases have been fired in your rifles chamber, sometimes twice.

    JM2c

    Comment

    • #3
      CGZ
      Senior Member
      • Nov 2014
      • 992

      I'm thinking it's the trimmer your using. Some of the cheaper ones I was getting the variations you're talking about (Lee trim dies) but then I got a Lyman universal case trimmer and am getting extremes of only +/- 0.02 when using the power adapter.

      Comment

      • #4
        NiMiK
        Senior Member
        • Jun 2011
        • 501

        You may want to check/measure your shoulders. The WFT or any trimmer that trims based on the shoulder will give different results if the case shoulders are not consistent with the other cases. You can measure using a 40S&W case or you can get a Sinclair or Hornady like below:

        Comment

        • #5
          LynnJr
          Calguns Addict
          • Jan 2013
          • 7959

          As PacRat said your brass probably needs a couple firings before it is long enough to get a consistent shoulder bump.
          The tool mentioned above should show 0.002 or less variation when measuring from the cases head to the shoulder.
          Technique plays a larger role as the case length is increased.
          If your shooting a 50 BMG you can use a piloted tool that centers off of the flashhole to keep the case necks square with the body.
          You want to trim to your shortest case but only after they actually need trimming.
          Lynn Dragoman, Jr.
          Southwest Regional Director
          Unlimited Range Shooters Association (URSA)
          www.unlimitedrange.org
          Not a commercial business.
          URSA - Competition starts at 2000 yards!

          Comment

          • #6
            micro911
            Senior Member
            • Jan 2013
            • 2346

            Originally posted by pacrat
            More info needed as to cause of variation. What type trimmer are you using? Lathe type that indexes off the base? Or one that indexes off the shoulder?

            If the former, and still getting variations that big. You technique is likely at fault.

            If the latter, that is to be expected until the cases have been fired in your rifles chamber, sometimes twice.

            JM2c
            This sounds about right. I used the Forster trimmer and it works very nicely, and very consistent.

            Comment

            • #7
              pacrat
              I need a LIFE!!
              • May 2014
              • 10287

              Originally posted by micro911
              This sounds about right. I used the Forster trimmer and it works very nicely, and very consistent.
              That's why I have 2 Forster trimmers. Both set up as power trimmers. One for trimming lenght. And one dedicated to neck turning bottleneck cases.

              Comment

              • #8
                LynnJr
                Calguns Addict
                • Jan 2013
                • 7959

                If your using a Forster trimmer technique is very important.
                You need to push on the crank so the casehead stays firmly against the collet. If you don't as you tighten the collet the cases will push forward and you will get more variation.
                Lynn Dragoman, Jr.
                Southwest Regional Director
                Unlimited Range Shooters Association (URSA)
                www.unlimitedrange.org
                Not a commercial business.
                URSA - Competition starts at 2000 yards!

                Comment

                Working...
                UA-8071174-1