kernals stuck in 223 cases

[captn-tin]

Just got thru sizing, swaging primer pockets, and tumbling about 1,000 rnds 223 cases. While trimmin up case mouths, I noticed there was still a few, maybe 3 - 4 pieces of walnut shell stuck in the cases. Will this hurt to just leave there and load as normal? I wonderin if the polishing media is stuck in lube that didn't get cleaned out of inside of case, and if the lube will have any affect on the powder.The lube is Dillon spray type. Brass was vibrated for about 2 hrs.
Thanks for any help

[pdq_wizzard]

Just got thru sizing, swaging primer pockets, and tumbling about 1,000 rnds 223 cases. While trimmin up case mouths, I noticed there was still a few, maybe 3 - 4 pieces of walnut shell stuck in the cases. Will this hurt to just leave there and load as normal? I wonderin if the polishing media is stuck in lube that didn't get cleaned out of inside of case, and if the lube will have any affect on the powder.The lube is Dillon spray type. Brass was vibrated for about 2 hrs.
Thanks for any help

you need to get the media out of the case, I don't think it will cause big issues, but it will take up powder space, that will change the way the power burns.

if you are loading to the edge it can cause issues with over pressure.

[troysland]

I use this for that same purpose. I have a few on my reloading bench.

[boomer135]

How are you reloading progressive or single stage?

If you are using a progressive, simply use a universal deprime die in station #1 to knock out any media.

If you are using a single stage then during inspection knock them out with a nail or other tool.

[Air]

I would try to get out as much as possible, but realistically just make sure the flash holes are clear of any debris and you should be good to go. You can buy a little pick set at Harbor Freight for a few bucks that will assist you, or as posted a little screwdriver. Don't overthink it, just do your best.

[LynnJr]

Your not tumbling for long enough if the walnut is stuck to your lube.

[Jon Road King]

Run your tumbler 15 minutes after you add cleaner, but BEFORE you add brass.

Also, you didn't mention if they were stuck inside the case, or in the flash hole (like i suspect). If that is the case, then just get used looking for it... it happens sometimes. Personally, I load 5.56 on a progressive after all brass is processed, but use a Lee standard de-capper in the first station to knock out any plugged flash holes.

[captn-tin]

Sorry didn't explain better. Media is stuck in the case mouth, not flash holes.

[TKM]

Use smaller media. I use lizard bedding from Wally World.

[hambam105]

What is the difference between leaving tumbling media inside your cartridge case during the assembly process, and leaving a few of those peskie gray & white sand pebbles the ranges use to keep the dust level down inside the case?

Lets see...YouTube...ammunition....reloading...dirt...g ravel... Ah! Here it is, Foreign Objects, See Quality Control, Page 1, Main Heading first sentence.

[mycrstuff]

Are you using a case/media separator like the ones from Dillon or RCBS? They get most of the media out unlike just shaking the cases with your hands. Also your media may be too wet. It soaks up polish and every so often you should put a used dryer sheet in the tumbler and it will soak up the excess polish.

http://www.midwayusa.com/product/176956/rcbs-rotary-case-and-media-separator

[Seaweed02]

Wet tumbler

Or you could invest in a wet tumbler. Even a cheap one from Harbor Freight is very helpful. Dry tumble your brass first, then size/deprime, then wet tumble and your brass is good to go like new.

[AandO]

How are you reloading progressive or single stage?

If you are using a progressive, simply use a universal deprime die in station #1 to knock out any media.

If you are using a single stage then during inspection knock them out with a nail or other tool.

That is what I do as well.

GTG

[hambam105]

When the "kernals'' are sticking to the inside of the case shoulder....
A decapping pin might very well too narrow to scrap the inside shoulder.

This does happen from time to time when you use something akin to the RCBS lube on the inside of the necks when resizing.

I was surprised as heck to see a much more experienced reloader than I wash rifle brass in hot soapy water after using a water soluble case lube on the inside neck of all the rifle brass in the re-forming process.

[the86d]

Just use fine-grit cob... it works fine for me, and only one tumble... with some mineral spirits and Brasso (do research before commenting on Brasso).
(My lady's allergic to walnuts.)