Unconfigured Ad Widget

Collapse

6.5 Grendel Upper, issues

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • USMCM16A2
    Banned
    • Jul 2006
    • 4941

    6.5 Grendel Upper, issues

    20 Inch BHW barrel, rifle length gas system, issues at range.
    Folks,



    I have a new upper that built on an M4E1 Aero Precision upper and the formentioned BHW 20 inch barrel. It is a type-1, and I have a standard 7.62x39 .125 bolt. The gas sytem is Seekins .750, adjustable. I got the gas system dialed in so its kicking the shells at 3 oclock. Accuracy was excellent.
    But about every 3rd or 4th shot, the bolt will pick up the shell, but it wont go completely into battery. The magazines I used are AA 10 rounders, bought from MidwayUSA. The ammo is 123gr A-Max, over 28.7gr of CFE-223, x 2 fired PPR brass, a Fedral 210M primer, COAL is 2.241. Cases were full length resized, and trim to length was 1.54. Help any body, A2 Carbine buffer and tube, rilfe length gas system.
  • #2
    LowThudd
    Veteran Member
    • Dec 2011
    • 3608

    Does the barrel have M4 feed ramps? Being that it is a rifle barrel, it might not. Assuming the upper has M4 feed ramps, this could be an issue.

    Comment

    • #3
      USMCM16A2
      Banned
      • Jul 2006
      • 4941

      It does have M4 feed ramps.

      Thudd,



      It does have M4 feed ramps. A2

      Comment

      • #4
        liber
        Senior Member
        • Dec 2014
        • 1868

        I had a similar problem with an AP M5E1 upper (308), and I would get an FTF about every 20-30 rounds.

        Bought a couple DPMS metal mags, and no FTFs for 2 months (1 range visit a month, about 200 rounds each visit).

        I was using PMAGs when I had the FTFs.

        I haven't taken the time to troubleshoot the PMAGs more, but I noticed also on my AR-15 that the PMAGs have quite a bit less space in the mag than the one metal mag I have.

        I've always kinda favored PMAGs, but starting to think it's better to use metal.
        sigpic
        --------- liber --------

        From my cold dead end mill...

        Comment

        • #5
          USMCM16A2
          Banned
          • Jul 2006
          • 4941

          Using the best mags available.

          folks,



          Keep the hints coming, I am using Alexander Arms 6.5 Grendel Mags. A2

          Comment

          • #6
            rg1
            Member
            • May 2008
            • 274

            Don't do anything until you've read this article:

            The ejector pins on all 6.5 Grendels or large case head calibers should be rounded and polished. The large head has trouble sliding over the squared ejector pins especially from the right side of the magazine. It's hard to remove and reinstall the ejector pins without proper ejector pin installation tools but is possible. Round and polish the tip of your ejector pin. Also, some good articles on polishing the extractor which also helps extraction but yours sounds like it's doing ok. All my feeding and ejection problems went away after doing the ejector pin and extractor polishing.
            Last edited by rg1; 10-20-2015, 9:09 PM.

            Comment

            • #7
              LowThudd
              Veteran Member
              • Dec 2011
              • 3608

              Originally posted by rg1
              Don't do anything until you've read this article:

              The ejector pins on all 6.5 Grendels or large case head calibers should be rounded and polished. The large head has trouble sliding over the squared ejector pins especially from the right side of the magazine. It's hard to remove and reinstall the ejector pins without proper ejector pin installation tools but is possible. Round and polish the tip of your ejector pin. Also, some good articles on polishing the extractor which also helps extraction but yours sounds like it's doing ok. All my feeding and ejection problems went away after doing the ejector pin and extractor polishing.
              Wow. Good info. As I am planning a 6.5 build, that is very useful info to keep in mind.

              Comment

              • #8
                USMCM16A2
                Banned
                • Jul 2006
                • 4941

                Thanks.

                rg,



                Thanks a ton. That is extactly what the shell looked like, when failing to go into battery. A2

                Comment

                • #9
                  LowThudd
                  Veteran Member
                  • Dec 2011
                  • 3608

                  A2, please report back if you are able to fix it with RGs advice.

                  Comment

                  Working...
                  UA-8071174-1