Unconfigured Ad Widget

Collapse

Does muzzle velocity actually affect HANDGUN accuracy?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Lead Waster
    I need a LIFE!!
    • Sep 2010
    • 16650

    Does muzzle velocity actually affect HANDGUN accuracy?

    OK, I get that with a rifle and 100 yard ranges, velocity changes "flight time" which can mean more time to drop from gravity, or to be pushed around by the wind. That momentum and kinetic energy affect point of impact.

    Do handgun rounds need actually benefit from higher velocity at 25 yards or less?

    People adjust their loads to increase velocity, why? And I don't mean "to mean the power factor floor" of their favorite shooting sports.

    Will an extra 100 fps help you shoot more accurately? Will it increase recoil and mess up your second shot? or will it get the bullet out of the barrel faster before you can flinch your shot off target?

    Thoughts?
    ==================

    sigpic


    Remember to dial 1 before 911.

    Forget about stopping power. If you can't hit it, you can't stop it.

    There. Are. Four. Lights!
  • #2
    acourvil
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Mar 2010
    • 532

    For most people using common guns, increasing the velocity beyond that necessary for proper, consistant function will have an adverse effect on accuracy due to the increased recoil.

    Comment

    • #3
      pacrat
      I need a LIFE!!
      • May 2014
      • 10287

      Originally posted by Lead Waster
      OK, I get that with a rifle and 100 yard ranges, velocity changes "flight time" which can mean more time to drop from gravity, or to be pushed around by the wind. That momentum and kinetic energy affect point of impact.

      [1] Do handgun rounds need actually benefit from higher velocity at 25 yards or less?

      [2] People adjust their loads to increase velocity, why?

      [3] Will an extra 100 fps help you shoot more accurately?

      [4] Will it increase recoil and mess up your second shot?

      [5] or will it get the bullet out of the barrel faster before you can flinch your shot off target?

      Thoughts?
      [1] Under certain circumstances, YES. Hard cast lead bullets at low velocity are also operating at low pressure levels. That lower pressure level can "fail" to obturate the hard lead bullet. Making it not fit the bore properly. Making the bullets flight unstable. I've had hardcast SWCs keyhole at 750 fps from a 4" revolver at 25 Yds. But fly just fine at 900 fps from same pistol.

      [2] {a}Shooting rabbits or shooting bears. {b} Match load to game. {c} Also to make POA meet POI.

      [3] Refer to [1] and [2]

      [4] Increasing velocity, increases recoil with given bullet/gun combo. Making target aquisition recovery slower.

      [5] Too Late. Flinch occurs before or during actual trigger break. Lock time and time of flight in barrel, are measured in "a few Thousandths of a Second".

      JM2c

      Comment

      • #4
        scotty99
        Senior Member
        • Dec 2009
        • 1184

        Test it, and you'll see. I have had pistol group sizes reduce by 50% with a 50fps change in muzzle velocity. But faster isn't always better. Every barrel has a few "nodes" - essentially velocities for a given bullet where the barrel is at its most accurate. This was explained to me as having to do with shockwave propagation down the length of the barrel, and timing the bullet to leave out of phase with the shockwave. I don't claim to understand the physics, but the results are easy to see with basic ladder testing.


        Sent from my iPad using Tapatalk HD

        Comment

        • #5
          hermosabeach
          I need a LIFE!!
          • Feb 2009
          • 19894

          If you are hunting or shooting silhouettes, and extreme accuracy is key, work up a load the same as you would with a rifle.

          If shooting people sized targets at 7 -12 yards, then come up with a reliable load for your platform...
          1 MOA at 25 yards is 1/4"

          1 MOA at 12 1/2 yards is an 1/8" inch


          So if a load is reliable and meets your power needs, who cares if it is 1-2 MOA larger at 100 yards.... If you shoot at 6 yards where an extra 2 MOA is 1/8" inch on the group....
          Rule 1- ALL GUNS ARE ALWAYS LOADED

          Rule 2 -NEVER LET THE MUZZLE COVER ANYTHING YOU ARE NOT PREPARED TO DESTROY (including your hands and legs)

          Rule 3 -KEEP YOUR FINGER OFF THE TRIGGER UNTIL YOUR SIGHTS ARE ON THE TARGET

          Rule 4 -BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT
          (thanks to Jeff Cooper)

          Comment

          • #6
            Whiterabbit
            Calguns Addict
            • Oct 2010
            • 7602

            Lead Waster,

            It's a huge deal. At least for us revolver shooters. The operative parameters (qualitatively) aren't bullet drop though, That is overwhelmed by barrel time.

            In other words, a faster load, all things equal, typically relate to a lower POI on paper due to less time for the gun to be in recoil before the bullet exits the muzzle.

            Beyond that, grip consistency is king, and velocity can affect that if you are crossing the threshold of your recoil tolerance.

            My answer to your questions, is that I personally strive to develop an inherently accurate load. I do this on bags. This load may or may not be at or beyond recoil tolerance. That I can build up over time with practice. Not exactly an answer to you question, but I hope it provides perspective.

            If your question really is "some guy said he was trying to get an extra 100 fps out of his pistol cause he said it would be more accurate and I have no idea why", I have no idea either. makes no sense to me.

            Comment

            • #7
              TMB 1
              Calguns Addict
              • Dec 2012
              • 7153

              Some of my most accurate loads in my 44mag are max loads. I'm more accurate for a longer period with 1000 to 1200fps loads though.
              sigpic

              Comment

              • #8
                Pauliedad
                CGN/CGSSA Contributor - Lifetime
                CGN Contributor - Lifetime
                • Dec 2012
                • 2095

                When I first started reloading I was doing ladder tests with all sorts of different powder-bullet-oal combinations with pistol.
                What I found was that while there were a few hideous combinations out there, they all went bang and at 25 yards there was much similarity.
                I also found that while I was doing all this work, I could adjust to the load pretty quickly. I shoot too many different pistol platforms to continue this quest and landed on the conclusion that I should have ammo that works well in whatever I shoot the most. This all applies to 9, 40, and .45acp.
                For the bigger stuff, I still experiment but find that I can adjust quickly so I tend to make up three kinds of loads. 1, ridiculously soft shooting, yes, it shoots way low and I swear I have to lob it on to the target. 2, medium, (this is what I stock the highest quantity of) slightly less than factory. 3, at least factory and preferably just a little hotter.

                Once I started loading rifle, that's where most of my energy goes in load development.

                Comment

                • #9
                  Calif Hunter
                  Veteran Member
                  • Aug 2003
                  • 3326

                  With fixed sights, it is a way to find the load that shoots best to point of aim. Faster, slower, heavy bullet, light bullet, etc.

                  Comment

                  • #10
                    Whiterabbit
                    Calguns Addict
                    • Oct 2010
                    • 7602

                    with fixed sights and an unwillingness to regulate those sights to the most accurate load

                    Otherwise, you take a file to the front sight and make it work.

                    Or I guess you are right. With fixed sights, it is "a" way.

                    Comment

                    • #11
                      Calif Hunter
                      Veteran Member
                      • Aug 2003
                      • 3326

                      Filing the front sight only works one way - to go the opther direction you have to weld to add height to the front sight or start filing on the rear sight. I prefer to tailor the load than permanently alter my gun. So I guess you are right - I am unwilling to regulate my sights to the most accurate load with existing components.

                      Comment

                      • #12
                        Whiterabbit
                        Calguns Addict
                        • Oct 2010
                        • 7602

                        Or replace the front sight blade. Of course.

                        Comment

                        • #13
                          Calif Hunter
                          Veteran Member
                          • Aug 2003
                          • 3326

                          On a Colt SAA?

                          Comment

                          • #14
                            CSACANNONEER
                            CGN/CGSSA Contributor - Lifetime
                            CGN Contributor - Lifetime
                            • Dec 2006
                            • 44094

                            Originally posted by Lead Waster
                            OK, I get that with a rifle and 100 yard ranges, velocity changes "flight time" which can mean more time to drop from gravity, or to be pushed around by the wind. That momentum and kinetic energy affect point of impact.

                            Do handgun rounds need actually benefit from higher velocity at 25 yards or less?

                            People adjust their loads to increase velocity, why? And I don't mean "to mean the power factor floor" of their favorite shooting sports.

                            Will an extra 100 fps help you shoot more accurately? Will it increase recoil and mess up your second shot? or will it get the bullet out of the barrel faster before you can flinch your shot off target?

                            Thoughts?
                            The reality is that MV will affect both accuracy and precision. However, it really depends on the bullet, case capacity and the exact load from that exact barrel. Sometimes a slower load will give the best performance and sometimes a hotter load will. However, if I'm reading your question right, you are really asking if dwell time affects precision, right? Dwell time is the amount of time the bullet is traveling through the barrel and precision is how consistent your groups are. Accuracy is only about all point of impacts being centered around the point of aim and muzzle velocity is just the speed that the bullet leaves the muzzle. It is possible for one load to have a faster MV but a longer dwell time and visa versa.
                            NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                            California DOJ Certified Fingerprint Roller
                            Ventura County approved CCW Instructor
                            Utah CCW Instructor


                            Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                            sigpic
                            CCW SAFE MEMBERSHIPS HERE

                            KM6WLV

                            Comment

                            • #15
                              Whiterabbit
                              Calguns Addict
                              • Oct 2010
                              • 7602

                              Originally posted by Calif Hunter
                              On a Colt SAA?
                              Mine is a vaquero, but sure.

                              Here's a dovetailed SAA



                              If you want to play the "I don't have the money for that" game, and the "I'm not willing to use a file" game, by all means: regulate your loads to your gun and hope for the best for accuracy. I'm sure accurate loads can be found without regulating sights.

                              I'm just suggesting that it takes a bit of luck to find an accurate load that shoots to the existing sights, unless you are shooting 15-25 yards max.
                              Last edited by Whiterabbit; 10-05-2015, 2:54 PM.

                              Comment

                              Working...
                              UA-8071174-1