Unconfigured Ad Widget

Collapse

Thoughts on minimal-space loading setups?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • CHS
    Moderator Emeritus
    CGN Contributor - Lifetime
    • Jan 2008
    • 11338

    Thoughts on minimal-space loading setups?

    So, as much as I want a Dillon 650, there's just no way I have the room for that kind of set-up right now. Especially because since I'm now casting, I also need room for a lube sizer.

    What I've been thinking about getting is either a single-stage press and a lube sizer, or a turret press and a lube sizer and then mounting them to the deck of this thing (Harbor Freight):



    With this little workstation, I can store it pretty easily in the garage and then move it to my room or the backyard or living room for reloading. I was thinking I could also get a spare top and use it for mounting my Master-Caster for when I want to do bullet casting.

    So, thoughts? Is this a good plan?

    Also, what are the main differences between a turret press and a single-stage? A turret press is just a single-stage with a rotating head so that you don't have to swap out dies for each operation, correct? These are approaching "too big" for my space requirements, but seem like maybe a good compromise between a slow-but-compact single-stage and a wicked-fast-but-huge Dillon 650 progressive.
    Please read the Calguns Wiki
    Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes...Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than to prevent homicides, for an unarmed man may be attacked with greater confidence than an armed man.
    --Cesare, Marquis of Beccaria, "On Crimes and Punishment"
  • #2
    Trapper
    Senior Member
    • Dec 2007
    • 2161

    It should work but you may want to add weight or bolt it down for stability.
    When the battle drum beats, it is too late to sharpen your sword."
    Sir Winston Churchill

    Comment

    • #3
      thebloodsonthewall
      Senior Member
      • Mar 2007
      • 1143

      Originally posted by Trapper
      It should work but you may want to add weight or bolt it down for stability.
      You will have to add weight or it will tip over. I have that problem with my reloading bench. I have about 75 lbs of weights stacked on the back corners so it doesn't tip over. I don't think the Dillon will take up much more room. It will probably be taller and weight more though. Are you doing just pistol or rifle as well? You will need a case trimmer somewhere on there also if you are reloading rifle rounds.

      Comment

      • #4
        armygunsmith
        Senior Member
        • Oct 2008
        • 2087

        I saw this idea on another site. http://accurateshooter.wordpress.com...ch-free-plans/
        They use a Black&Decker Workmate. I've been considering a similar setup for myself. The way the bench sits, it looks like you wouldn't need to add too much weight to keep it stable. You could probably get a progressive to fit on it but haven't tried yet.
        SECRET//NOFORN
        "Sometimes it's easier to do it the hard way."
        Sgt. E <--(That's me)

        Comment

        • #5
          CHS
          Moderator Emeritus
          CGN Contributor - Lifetime
          • Jan 2008
          • 11338

          Originally posted by thebloodsonthewall
          You will have to add weight or it will tip over. I have that problem with my reloading bench. I have about 75 lbs of weights stacked on the back corners so it doesn't tip over. I don't think the Dillon will take up much more room. It will probably be taller and weight more though. Are you doing just pistol or rifle as well? You will need a case trimmer somewhere on there also if you are reloading rifle rounds.
          The problem with something like the Dillon is that this setup is going to have to remain somewhat portable. I don't want to move around a workstation with a Dillon completely set-up much, if any at all. Plus, being taller and much heavier, will be a lot more awkward to move around. I guess I should have said "portable" rather than minimal-space, but both are pretty important.

          Pistol and rifle.

          Any thoughts on single-stage vs. turret?
          Please read the Calguns Wiki
          Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes...Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than to prevent homicides, for an unarmed man may be attacked with greater confidence than an armed man.
          --Cesare, Marquis of Beccaria, "On Crimes and Punishment"

          Comment

          • #6
            fairfaxjim
            Senior Member
            • Apr 2006
            • 2146

            I have my Dillon Square Deal B mounted on a Craftsman rollaway tool box, just the lower drawer set. It works great. It would benefit from an easy way to fix it to a wall or door frame when using it to gain some more stability, but it works. Has lots of drawer space too to hold supplies and tools, easy to roll around and tucks out of the way.

            I am planning on adding a Hornady Lock-N-Load progressive on the other side.
            "As soon as we burn 'em," Chinn said, "more come in."
            Ignatius Chinn, a FORMER veteran firearms agent.
            CONTRA COSTA TIMES 03/04/2008

            "please guys please no ridiculous offers....Im a girl, not an idiot" Mistisa242

            Comment

            • #7
              Revoman
              Senior Member
              • Dec 2007
              • 2394

              I have also used a Black & Decker 'Work-Mate' style table. It really works well. It's very stable and is hard to tip over, plus it has a sort of step that can be used to rest your feet on. The legs are built heavy enough to be able to withstand the pressure/weight of reloading.
              It also folds up so storage is minimal.
              I used one for shotgun loading, but it should also work well for metallic.
              The link provided earlier shows a nice set up, that would work very well.
              It was plenty large enough, but it also can expand. All this and you can still use it for it's intended purpose.........a portable work bench!
              I simlpy used 'C' clamps to mount the loader.

              Comment

              • #8
                TKM
                Onward through the fog!
                CGN Contributor
                • Jul 2002
                • 10657

                I purchased a butcher block table island from World Mart or something similar.

                It's 24x24 and the work surface is 34 inches high. It's on wheels and has a lower shelf.

                I have a Pro 2000 on one side, a five inch HF vice and anvil to the left and facing it is an Ammomaster set up for 50 BMG. It's a pretty slick little setup and I can take it outside if it's a nice day.

                I store 300 lbs +- of lead on the lower shelf, it's pretty stable.
                It's not PTSD, it's nostalgia.

                Comment

                • #9
                  xrMike
                  Calguns Addict
                  • Feb 2006
                  • 7841

                  Originally posted by bdsmchs
                  Also, what are the main differences between a turret press and a single-stage? A turret press is just a single-stage with a rotating head so that you don't have to swap out dies for each operation, correct? These are approaching "too big" for my space requirements, but seem like maybe a good compromise between a slow-but-compact single-stage and a wicked-fast-but-huge Dillon 650 progressive.
                  With the turret press you'll save time/trouble in 2 ways (over a single-stage):

                  1. You adjust your dies once and forget about it.

                  2. You only have to move your brass ON/OFF the shellholder 1 time per round (versus 4 times per round with single-stage, assuming crimp die is used)

                  Comment

                  • #10
                    rayra
                    Banned
                    • Mar 2006
                    • 1747

                    Creative solution but a bad idea. You need a much more substantial mounting for your press / for the forces involved.

                    Just use bolts and fender washers and wingnuts to mount your press to your workbench, then dismount it and store it aside when not in use. Only take a couple minutes and won't be in the way the rest of the time.


                    /eta - you DO have a garage workbench, don't you?

                    /wondering why portability is even an issue / desire, seems odd.
                    Last edited by rayra; 11-25-2008, 1:53 PM.

                    Comment

                    • #11
                      CHS
                      Moderator Emeritus
                      CGN Contributor - Lifetime
                      • Jan 2008
                      • 11338

                      Originally posted by rayra
                      /eta - you DO have a garage workbench, don't you?

                      /wondering why portability is even an issue / desire, seems odd.
                      No. Otherwise I wouldn't be asking this question.

                      I rent a large room in a house here in HB. I only have one roomie (the house owner). I have plenty of storage space in the garage, but not enough room or dedicated space to have my own garage workbench. I don't have enough room in my bedroom to have a permanent non-portable workbench, no matter how small it is.

                      I could probably keep a decent-sized workbench in the backyard, but that would not be practical due to the elements. And I would definitely not want to have any reloading equipment permanently mounted to it.

                      So in the end it all comes back to a portable solution.

                      Single stage or smaller turret press and lube-sizer mounted to a small portable workstation that can be stored in a corner of the garage covered and protected from the elements, but can be moved to my room or backyard or wherever for reloading day. And then back to the garage when I'm done with it.

                      I wouldn't have asked all this without very good reason. If I could have a nice workbench in the garage then I would already have a Dillon 650 mounted on it and we wouldn't be having this discussion.
                      Please read the Calguns Wiki
                      Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes...Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than to prevent homicides, for an unarmed man may be attacked with greater confidence than an armed man.
                      --Cesare, Marquis of Beccaria, "On Crimes and Punishment"

                      Comment

                      • #12
                        rayra
                        Banned
                        • Mar 2006
                        • 1747

                        Let me expand on my remarks about 'portability'.

                        Particularly, your posts seem to give the impression that your intent is to set up your relaoding gear in a variety of locations about your house. I can only surmise that part of your quest is the ability to sit with others while you reload, or even attempt to watch kids or TV, or carry on a some other heavily distracting activity while you are reloading.
                        This is what's called A BAD IDEA.
                        Your attenion needs to be focused on what you are doing when you are reloading. At least when it comes time for powder and primers & bullet seating. You should NOT be deliberately seeking to facilitate a situation where you can be distracted and make a danger mistake involving gunpowder.

                        In fact you should be striving to do the OPPOSITE of what you seem to be seeking. You ought to be seeking to create an organized, stable and distraction-free environment for reloading. Not looking to ALSO reload while you do something else.

                        Comment

                        • #13
                          rayra
                          Banned
                          • Mar 2006
                          • 1747

                          ok, just read your last post.

                          I would suggest 'borrowing' whatever workbench you have access to when you want to reload. And set your press up on a 3/4 plywood baseplate, which you then clamp onto the existing workbench. And when not in use, you simply unclamp your equipment and pack it away.

                          I've seen some 'portable' crates, similar to a military footlocker, set up to store the full panoply of reloading equipment. But also configured to serve as a portable workbench to affix the gear to, usually placed on a truck tailgate to use. Maybe you can construct something along those lines.

                          The other basic question is if you've got the space for that little portable table, you've basically got space for a mini workbench with a footprint that isn't much larger.

                          I've also seen folks use old desks as workbenches, affixing or clamping their presses to the desks when its needed.

                          Comment

                          • #14
                            buffybuster
                            Veteran Member
                            • Oct 2005
                            • 2615

                            Originally posted by rayra
                            Creative solution but a bad idea. You need a much more substantial mounting for your press / for the forces involved.

                            +1

                            To make consistent ammunition you need a stable, non-deflecting platform to mount the press on. I'll surmise with nearly all these "portable" setups, if you were to carefully inspect them during resizing that the table is deflecting under the stress. You might not be able to "see" it and you will be able to make "workable" ammo but it's far from ideal. Nothing beats having a thick bench top with a substantial amount of mass on the entire bench or having it mounted to the wall studs (more mass).

                            RCBS has a mounting plate that you can secure to a bench then mount/dismount presses, etc as you need them.


                            bds: You mentioned that you're casting bullets, where you keeping that stuff?
                            Luck favors the prepared.

                            The original battle plan did not survive initial contact with the enemy.

                            "The things that will destroy America are prosperity at any price, peace at any price, safety first instead of duty first, the love of soft living and the get rich quick theory of life." -Theodore Roosevelt

                            Comment

                            • #15
                              CHS
                              Moderator Emeritus
                              CGN Contributor - Lifetime
                              • Jan 2008
                              • 11338

                              Thanks for all the tips guys. I now think I have a better idea of the way I should be going with this.


                              Originally posted by buffybuster
                              To make consistent ammunition you need a stable, non-deflecting platform to mount the press on. I'll surmise with nearly all these "portable" setups, if you were to carefully inspect them during resizing that the table is deflecting under the stress. You might not be able to "see" it and you will be able to make "workable" ammo but it's far from ideal. Nothing beats having a thick bench top with a substantial amount of mass on the entire bench or having it mounted to the wall studs (more mass).


                              RCBS has a mounting plate that you can secure to a bench then mount/dismount presses, etc as you need them.
                              Now that's definitely something I didn't know and really appreciate the tip. Makes perfect sense. I just hadn't thought of that. Unless I replace the top of that workstation with a very substantial top, you're probably right in that I'll get inconsistent ammunition.


                              Originally posted by buffybuster
                              bds: You mentioned that you're casting bullets, where you keeping that stuff?
                              Currently, I'm rebuilding the master-caster that I just got a good deal on (bad heaters). I've got 4 buckets of lead in the garage, but I'm actually going to be casting at a friends house.

                              I'll also probably be able to set up an area in the backyard where I can cast, but I'm not thinking about that right now.
                              Please read the Calguns Wiki
                              Laws that forbid the carrying of arms...disarm only those who are neither inclined nor determined to commit crimes...Such laws make things worse for the assaulted and better for the assailants; they serve rather to encourage than to prevent homicides, for an unarmed man may be attacked with greater confidence than an armed man.
                              --Cesare, Marquis of Beccaria, "On Crimes and Punishment"

                              Comment

                              Working...
                              UA-8071174-1