Unconfigured Ad Widget

Collapse

Cutting Down Necks

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • J-cat
    Calguns Addict
    • May 2005
    • 6626

    Cutting Down Necks

    I need some help.

    I'm starting a semi-wildcat project where I need to cut off .200" off the case neck. I thunk about it and developed the following options:

    1. Belt sand off most of it, then get close with something like a Trim-It, then finish trim on my Wilson.

    2. Cut off most of it using a miter saw, followed by the above.

    3. Use a Trim-It instead of the belt sander or miter.

    4. Drag the case mouth on the sidewalk.

    5. Not do it.

    Does the Trim-It have the capability to remove .200" off the case neck? I saw they sell a 4-flute cutter and I called them but didn't get a real good answer.
  • #2
    G-Man WC
    In Memoriam
    • Oct 2005
    • 10991

    HF mini 2" chop saw.
    -g
    If ever time should come, when vain and aspiring men shall possess the highest seats in Government, our country will stand in need of its experienced patriots to prevent its ruin.
    -Samuel Adams

    Comment

    • #3
      JMP
      Internet Warrior
      CGN Contributor - Lifetime
      • Feb 2012
      • 17056

      Most power trimmers index off the shoulder angle, so if you use the appropriate pilot with the correct angle, it should work. May I ask what case you are starting with?

      Comment

      • #4
        klewan
        Veteran Member
        • Jun 2011
        • 3031

        Look up 300 blk brass production; they've been doing it for the last 4 years. Cutting 10mm off .223 to make 300.

        Comment

        • #5
          J-cat
          Calguns Addict
          • May 2005
          • 6626

          They have dedicated jigs for those chop saws.

          Is a Trim-It appropriate for removing large amounts of brass? My Wilson with a carbide cutter sure isn't. But I haven't spun it on a power drill either.

          Comment

          • #6
            J-cat
            Calguns Addict
            • May 2005
            • 6626

            Originally posted by JMP
            Most power trimmers index off the shoulder angle, so if you use the appropriate pilot with the correct angle, it should work. May I ask what case you are starting with?
            You may not.

            Comment

            • #7
              pacrat
              I need a LIFE!!
              • May 2014
              • 10287

              Originally posted by J-cat
              They have dedicated jigs for those chop saws.

              Is a Trim-It appropriate for removing large amounts of brass? My Wilson with a carbide cutter sure isn't. But I haven't spun it on a power drill either.
              Don't know about the Wilson, I have 2 Foresters. Simply unscrewing the handle and using a variable speed cordless made a world of difference. Especially for neck turning.

              Even on slow setting it is still 100 times more rpm than you can crank with thumb and fore finger.

              Comment

              • #8
                JMP
                Internet Warrior
                CGN Contributor - Lifetime
                • Feb 2012
                • 17056

                Originally posted by J-cat
                You may not.
                The reason I was curious is that I have quite a few pilots and different caliber blades for my power trimmer, so I might have what you need that you could use.

                Otherwise, I am pretty sure the Giraud Power Trimmer would get the job done easily as Doug Giraud has about 200 different pilots where one will probably work even if you have an oddball.

                I have no experience with the Trim-It machine, but if that works the same way, I'd have no apprehension taking off 0.200"

                Comment

                • #9
                  J-cat
                  Calguns Addict
                  • May 2005
                  • 6626

                  I appreciate the offer but I don't wanna say cuz I'm not ready to unleash it just yet. But I will say that it's easy to make, does not require mods to your rifle, and improves the performance of a very popular cartridge.

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    For the first few test rounds, I would use my CH4D trimmer or my Lymann trimmer with a drill attached. Both are lathe type trimmers that index of the case head. As long as you're not cutting into the shoulder, just about any style trimmer will work. The problem with the ones that index of the shoulders is that you need the right bushing for the job.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      JMP
                      Internet Warrior
                      CGN Contributor - Lifetime
                      • Feb 2012
                      • 17056

                      OK J-cat, good luck. Do let me know the results when you are ready if it's based off of the 50 BMG. I am looking for a big wildcat, and I am pretty much sick of any brass other than Lapua or RWS.

                      Comment

                      • #12
                        stand125
                        Senior Member
                        • Jun 2010
                        • 1451

                        I have seen alot of jigs made out of a piece of wood that is simply channeled out and then clamped on the little harbor freight saw, then final trimming with something else like a standard trimmer.
                        CALGUNS DICTIONARY "FLIER": when a shooter wants to turn a 1 inch group to a half inch group because he flinched.

                        Comment

                        • #13
                          K7addict
                          Senior Member
                          • Feb 2012
                          • 641



                          I've used the Harbor Freight chop saw and a dedicated jig milled by a member on the cast boolits forum. I will say that it makes the job very quick and consistent to get very close to final length. I follow up with a Lee Quick trim after sizing for 300 blk out.

                          Good luck with your project

                          Comment

                          • #14
                            LynnJr
                            Calguns Addict
                            • Jan 2013
                            • 7959

                            J-Cat
                            If you have the reamer in your posession run it into a piece of barrel about 2 2-1/2 inches long. Only run the reamer in until you reach the shoulder then go in about an 1/8 inch more. Basically you are making a barrel stub like most accuracy gunsmiths provide with each build.

                            Run down to your local supply house and get yourself a 3/8 inch end mill and a shaft collar.
                            Flip your stub over and drill out the bore to 3/8 inch so the end mill will slide right in.

                            You have just built yourself a case trimmer you can run off of a drill. Spin the end mill until it is very close and lock down the shaft collar.

                            This is how meplat trimmers work and what benchrest shooters use to adjust case length.
                            Lynn Dragoman, Jr.
                            Southwest Regional Director
                            Unlimited Range Shooters Association (URSA)
                            www.unlimitedrange.org
                            Not a commercial business.
                            URSA - Competition starts at 2000 yards!

                            Comment

                            • #15
                              Whiterabbit
                              Calguns Addict
                              • Oct 2010
                              • 7602

                              .2"? good grief.

                              I've done a few hundred cases of a 7mm-223 wildcat. basically a 300 whisper (you can call it blackout if you want) necked to 7mm. The cut is more than .2".I just put them in a standard trimmer and powered though it.

                              If I wanted match grade brass, I would need to:

                              power trim through the bulk
                              Chamfer/deburr
                              Trim again to get a precise length
                              Maybe deburr, maybe not.

                              But for within say .005, not really an issue.

                              There is no reason to overthink this. Unless your trimmer can jam through a case in 1-2 seconds, you might overheat the cutter. But seriously, no need to overthink, especially for a tester batch.

                              Last edited by Whiterabbit; 05-24-2015, 11:06 PM.

                              Comment

                              Working...
                              UA-8071174-1