Unconfigured Ad Widget

Collapse

Once fired case prep ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 357shooter
    Senior Member
    • Jul 2010
    • 729

    Once fired case prep ?

    OK I have 40 cases fired in my 700 and I'm ready to prep them so I check
    the case length and most of them are under min. length 2.481 can I use these
    or do I have to FL size them I'm using a lee collet die for the neck.
    This was new ammo once fired so it should have formed to my chamber
    right. I thought the case got bigger after firing not smaller.
    Last edited by 357shooter; 05-08-2015, 7:34 PM.
  • #2
    triggs75
    Senior Member
    • Sep 2010
    • 1835

    Just use a neck die and you are good to go as long as you are shooting it out of the same rifle. At least that is my plan since I am relatively new to reloading as well

    Comment

    • #3
      Capt.Dunsel
      Senior Member
      • May 2011
      • 1199

      Originally posted by 357shooter
      OK I have 40 cases fired in my 700 and I'm ready to perp them so I check
      the case length and most of them are under min. length 2.481 can I use these
      or do I have to FL size them I'm using a lee collet die for the nick.
      This was new ammo once fired so it should have formed to my chamber
      right. I though the case got bigger after firing not smaller.
      Thought I would see a thread about someone stealing your Brass at the range,
      until I read it through . spell check is our friend .

      Figured it was supposed to be prep and neck and thought , am I correct ?

      I am getting old and my eyesight ain't what it used to be
      Bweise says "I have to say the situation was not at all helped by 22 yr old former Airsoft douches who kept touting here, "But possession is not illegal!" "

      Fighting on the internet is like being in the special Olympics , everybody wins but your still retarded.

      Librarian " Calguns is not a 'general discussion board".

      Comment

      • #4
        jimmykan
        Veteran Member
        • Jan 2008
        • 3105

        I'm guessing these are 30-06 cases, from the 2.481" length reference?

        That is not the minimum length, according to this SAAMI drawing:

        The dimension is 2.494 - 0.020 so the minimum length is 2.474.

        Either way, I bet if you measured the case length of an unfired cartridge, it would be very close to the fired case length. Brass usually elongates when you full length size it.

        If it was not too short for a factory loading, it probably is fine for your reloads too.
        Last edited by jimmykan; 05-08-2015, 2:40 PM.

        Comment

        • #5
          Diesel12
          Member
          • Jan 2014
          • 108

          Originally posted by triggs75
          Just use a neck die and you are good to go as long as you are shooting it out of the same rifle. At least that is my plan since I am relatively new to reloading as well
          This ^^^

          Comment

          • #6
            357shooter
            Senior Member
            • Jul 2010
            • 729

            Originally posted by jimmykan
            I'm guessing these are 30-06 cases, from the 2.481" length reference?

            That is not the minimum length, according to this SAAMI drawing:

            The dimension is 2.494 - 0.020 so the minimum length is 2.474.

            Either way, I bet if you measured the case length of an unfired cartridge, it would be very close to the fired case length. Brass usually elongates when you full length size it.

            If it was not too short for a factory loading, it probably is fine for your reloads too.

            Thanks I will print that out.

            Comment

            • #7
              357shooter
              Senior Member
              • Jul 2010
              • 729

              Originally posted by Capt.Dunsel
              Thought I would see a thread about someone stealing your Brass at the range,
              until I read it through . spell check is our friend .

              Figured it was supposed to be prep and neck and thought , am I correct ?

              I am getting old and my eyesight ain't what it used to be
              Yes you are correct.

              Comment

              • #8
                h.charlie
                Member
                • Feb 2014
                • 497

                You need measure after you size, and with the Lee collet neck sizer I find you will get better neck tension if you run a expander ball threw the case after neck sizing

                Comment

                • #9
                  JMP
                  Internet Warrior
                  CGN Contributor - Lifetime
                  • Feb 2012
                  • 17056

                  Originally posted by 357shooter
                  OK I have 40 cases fired in my 700 and I'm ready to prep them so I check the case length and most of them are under min. length 2.481 can I use these or do I have to FL size them I'm using a lee collet die for the neck.
                  The length of the neck mostly affects neck tension. As a rule of thumb, you'll want the neck to be at least one caliber size in length. This will ensure that you have enough contact to hold the bullet firmly and concentrically. As long as you have sufficient surfact aread for the neck to grip the bullet, you do not necessarily have a minimum length.
                  Originally posted by 357shooter
                  This was new ammo once fired so it should have formed to my chamber right.
                  The degree of success you have upon neck sizing only will depend on your chamber dimensions. Neck sizing only works well when you have a tight chamber and the case isn't getting a whole lot of horizontal expansion. If you have a loose chamber, you may have concentricity issues if you neck size only. For most factory barrels, I'd FL because they tend to be rather loose. Test some using both methods. In a well-dimensioned chamber, you can FL or not, in general, if the chamber is tight, the FL sizing only minimally resizes the case.
                  Originally posted by 357shooter
                  I thought the case got bigger after firing not smaller.
                  The case gets larger, but it is getting pushed outward against the walls of the chamber. The length of the case will get smaller. It will be longer after FL sizing.

                  Comment

                  • #10
                    357shooter
                    Senior Member
                    • Jul 2010
                    • 729

                    Originally posted by JMP
                    The length of the neck mostly affects neck tension. As a rule of thumb, you'll want the neck to be at least one caliber size in length. This will ensure that you have enough contact to hold the bullet firmly and concentrically. As long as you have sufficient surfact aread for the neck to grip the bullet, you do not necessarily have a minimum length.

                    The degree of success you have upon neck sizing only will depend on your chamber dimensions. Neck sizing only works well when you have a tight chamber and the case isn't getting a whole lot of horizontal expansion. If you have a loose chamber, you may have concentricity issues if you neck size only. For most factory barrels, I'd FL because they tend to be rather loose. Test some using both methods. In a well-dimensioned chamber, you can FL or not, in general, if the chamber is tight, the FL sizing only minimally resizes the case.

                    The case gets larger, but it is getting pushed outward against the walls of the chamber. The length of the case will get smaller. It will be longer after FL sizing.

                    Thank you great info.

                    Comment

                    • #11
                      LynnJr
                      Calguns Addict
                      • Jan 2013
                      • 7959

                      On once fired brass you can do some steps to help uniform your brass but these are not needed for plinking or hunting ammo.

                      As JMP posted your brass will shorten up when shot. When factory brass goes into the chamber is has plenty of space all around it. When it gets shot the case expands to the chambers dimensions.
                      Picture two chopsticks standing upward on a table top with about a 1/2 inch between them. If you keep the bottom of the two sticks a half inch apart and you spread them a little in the middle they are no longer as tall even though they are still the same length. When your brass expands to fill the chamber it shortens up just like the chopsticks. When you full length resize it the length comes back.
                      Last edited by LynnJr; 05-09-2015, 10:46 AM.
                      Lynn Dragoman, Jr.
                      Southwest Regional Director
                      Unlimited Range Shooters Association (URSA)
                      www.unlimitedrange.org
                      Not a commercial business.
                      URSA - Competition starts at 2000 yards!

                      Comment

                      Working...
                      UA-8071174-1