Unconfigured Ad Widget

Collapse

9mm set back questions/problems

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    hambam105
    Calguns Addict
    • Jan 2013
    • 7083

    From my perspective here at keyboard central...

    I'd say it's the plated bullets.

    Comment

    • #17
      J-cat
      Calguns Addict
      • May 2005
      • 6626

      Originally posted by maxxlara
      ok, I just tried it out 20 out of 20 blazer with sink back in,,, 20 out of 20 other head stamps will not.... any ideas???????
      Your non responses are not helping generate ideas.

      Comment

      • #18
        eaglemike
        CGN/CGSSA Contributor - Lifetime
        CGN Contributor - Lifetime
        • Jan 2008
        • 4002

        A couple of things can be contributing, looking at the posts......

        The plated bullets can sometimes be an issue. Very soft lead, and no "spring back" at all. (this has been alluded to above). When crimped, they simply crush. Traditional cast lead (and moly coated) stuff is typically hard, and will take a crimp better.

        Thin walled brass can also be an issue a times, when combined with worn out or over-sized sizing dies.

        You might have a combination of both issues as well........ (somewhat likely based on the posts above)
        There are some people that it's just not worth engaging.

        It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

        Comment

        • #19
          pacrat
          I need a LIFE!!
          • May 2014
          • 10287

          Originally posted by maxxlara
          ok, this is weired,, it only happens with blazer brass shells, everything else is fine,,, getting closer.....
          From my previous post.

          Optimal neck tension should be .001". - .002" at most. Brass work hardens with use. Different makers use different alloys and different heat treatments. So the amount of work hardening also varies with each firing/sizing.
          Time to use your calipers, do the math, and diagnose the issue. Keyboard isn't fixing the loose bullet problem.

          JM2c

          Comment

          • #20
            J-cat
            Calguns Addict
            • May 2005
            • 6626

            Blazer brass is not thin walled. It is the same damm brass as FC and CCI.

            This new ATK made brass is larger in diameter at the base than Win or RP and a lot of others. If you don't size it all the way down the sizing die may not size the neck correctly. This is a tapered case. Some dies absolutely need to bottom out against the shell holder. In the case of large diameter cases the die might stop short of doing this because the effort is hard, but then the neck will be undersized.

            Comment

            • #21
              eaglemike
              CGN/CGSSA Contributor - Lifetime
              CGN Contributor - Lifetime
              • Jan 2008
              • 4002

              Originally posted by J-cat
              Blazer brass is not thin walled. It is the same damm brass as FC and CCI.

              This new ATK made brass is larger in diameter at the base than Win or RP and a lot of others. If you don't size it all the way down the sizing die may not size the neck correctly. This is a tapered case. Some dies absolutely need to bottom out against the shell holder. In the case of large diameter cases the die might stop short of doing this because the effort is hard, but then the neck will be undersized.
              If you note his post above, he observed a difference with the blazer brass.

              If you are going to allege there isn't variance in lots of brass, we will disagree. I've been reloading for over 40 years, and served my apprenticeship at Star Machine Works in San Diego (if you know what that means. I also own my own CNC shop, over 25 years).
              There are some people that it's just not worth engaging.

              It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

              Comment

              • #22
                maxxlara
                Member
                • Jan 2011
                • 432

                Ok, I've been playing with it a bit more, happens with the blazer and fc shells. I've seperated them in their own tub. It makes up about 50% of my brass cases. Im doing some measuring and trying to find out why it only happens with those cases. And trying to find a way to get them to work. Gonna play with the resizing dies, both hornady and lee

                Comment

                • #23
                  maxxlara
                  Member
                  • Jan 2011
                  • 432

                  Thanks so much for all the great advice!!! I got them to hold by lowering my resizing die a bit further. After doing so they are all nice and tight!!!Not able to push them in any more..Before all the advice I kept playing with the crimp thinking that that was the problem...

                  Thanks Again
                  Maxx

                  Comment

                  • #24
                    eaglemike
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Jan 2008
                    • 4002

                    Well done.
                    9mm chambers vary quite a bit.
                    Since 9mm is tapered so much, sizing die adjustment makes a big difference.
                    If the projectile sets back, pressures go up quite a bit as well.
                    There are some people that it's just not worth engaging.

                    It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

                    Comment

                    • #25
                      J-cat
                      Calguns Addict
                      • May 2005
                      • 6626

                      Originally posted by eaglemike
                      If you note his post above, he observed a difference with the blazer brass.

                      If you are going to allege there isn't variance in lots of brass, we will disagree. I've been reloading for over 40 years, and served my apprenticeship at Star Machine Works in San Diego (if you know what that means. I also own my own CNC shop, over 25 years).
                      You have no idea how many different 9mm cases I have worked with or how many different 9mm platforms I've loaded for. Please don't try to school me about lot to lot variance.

                      Comment

                      • #26
                        eaglemike
                        CGN/CGSSA Contributor - Lifetime
                        CGN Contributor - Lifetime
                        • Jan 2008
                        • 4002

                        Originally posted by J-cat
                        You have no idea how many different 9mm cases I have worked with or how many different 9mm platforms I've loaded for. Please don't try to school me about lot to lot variance.
                        Either do you about me........
                        But don't worry, you are the smartest and best.
                        There are some people that it's just not worth engaging.

                        It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

                        Comment

                        • #27
                          J-cat
                          Calguns Addict
                          • May 2005
                          • 6626

                          Don't be bitter. You'll win the Internet eventually.

                          Comment

                          • #28
                            eaglemike
                            CGN/CGSSA Contributor - Lifetime
                            CGN Contributor - Lifetime
                            • Jan 2008
                            • 4002

                            You be funny. I was making 9mm sizing dies back in 1977..... as well as other handgun calibers.......
                            Nice to meet a REAL expert though.
                            There are some people that it's just not worth engaging.

                            It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

                            Comment

                            • #29
                              J-cat
                              Calguns Addict
                              • May 2005
                              • 6626

                              You're like the guy in the middle:


                              Last edited by J-cat; 04-20-2015, 1:09 AM.

                              Comment

                              • #30
                                eaglemike
                                CGN/CGSSA Contributor - Lifetime
                                CGN Contributor - Lifetime
                                • Jan 2008
                                • 4002

                                I've been nothing but courteous to you.
                                I'm don't have to prove anything here......
                                Whatever you need to win on the internet, you may assume you have first place.
                                Last edited by eaglemike; 04-20-2015, 9:03 AM. Reason: clarity
                                There are some people that it's just not worth engaging.

                                It's a muzzle BRAKE, not a muzzle break. Or is your muzzle tired?

                                Comment

                                Working...
                                UA-8071174-1