Unconfigured Ad Widget

Collapse

Bipod-first timer looking into buying? Know this:

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • nickel plate
    Senior Member
    • Jul 2012
    • 2148

    Bipod-first timer looking into buying? Know this:

    Yes, that was me. Set up my bipod-less rifle on the bench, assumed my shooting position and had my wife place a torpedo level on a flat spot on the top of the rifle barrel and she then directed me to a level bubble, wrote down the "plumb" measurement from that spot to the base of the table. I subtracted out the difference in her measurement to the base of the fore end where the bipod would be attached and had my bipod height measurement for my rifle, the plumb height was around 12".
    Here's where it became interesting:
    I'm a tall guy-long arms so right off the bat the most commonly purchased 6" to 9" bipod leg extension model wasn't going to work for me, I needed the next size up. Enter the 9" to 13" model which I thought would give me more than ample wiggle room-no.
    Now I'm not saying that all of the bipod manufactures measure there legs this way but I do know that the Harris Engineering products measures their legs on the angle, not the plumb height. Quoting there literature, "Extends from 9" to 13"" so a 9" to 13" does measure that at an angle from the leg bottom to the top of the bipod which is correct to their posted statement but the true and most important height of that same bipod is actually 8-1/8" to 11-7/8" on plumb.
    It would be most helpful if the manufactures would post "plumb" heights along with leg extension heights.
  • #2
    smittty
    Calguns Addict
    • Feb 2008
    • 6279

    Make sure it tilts AND turns!

    Comment

    • #3
      Erion929
      Veteran Member
      • Jan 2013
      • 4706

      Join Active Junky for online rebates....$10 to both you and me!

      https://www.activejunky.com/invite/238017


      Comment

      • #4
        Brush Guard
        Senior Member
        • Jan 2015
        • 888

        Originally posted by sfarchitect

        My personal bipod pet peeve is spring loaded legs, I hate(!) 'em. You build your position, get on the gun, line up your sites, try to load the bipod and SPROING! the bipod leg or legs fold and collapse. The least bad outcome here is your barrel or muzzle hits the bench/ground pretty hard. If you're hunting your target/quarry is now gone. I volunteer as an RO at my local range. I once saw exactly this kind of thing result in a (relatively harmless) ND on a public firing line.
        Is it possible to reverse the bipod on the rifle so the legs fold the opposite direction, in order to avoid the collapse?

        .

        .

        Comment

        • #5
          theLBC
          CGN/CGSSA Contributor
          CGN Contributor
          • Oct 2017
          • 7633

          Originally posted by Brush Guard
          Is it possible to reverse the bipod on the rifle so the legs fold the opposite direction, in order to avoid the collapse?

          .

          .
          sound like it is already mounted backwards.
          loading a harris bipod does not fold the front-folding legs.

          Comment

          • #6
            theLBC
            CGN/CGSSA Contributor
            CGN Contributor
            • Oct 2017
            • 7633

            Originally posted by nickel plate
            Yes, that was me. Set up my bipod-less rifle on the bench, assumed my shooting position and had my wife place a torpedo level on a flat spot on the top of the rifle barrel and she then directed me to a level bubble, wrote down the "plumb" measurement from that spot to the base of the table. I subtracted out the difference in her measurement to the base of the fore end where the bipod would be attached and had my bipod height measurement for my rifle, the plumb height was around 12".
            Here's where it became interesting:
            I'm a tall guy-long arms so right off the bat the most commonly purchased 6" to 9" bipod leg extension model wasn't going to work for me, I needed the next size up. Enter the 9" to 13" model which I thought would give me more than ample wiggle room-no.
            Now I'm not saying that all of the bipod manufactures measure there legs this way but I do know that the Harris Engineering products measures their legs on the angle, not the plumb height. Quoting there literature, "Extends from 9" to 13"" so a 9" to 13" does measure that at an angle from the leg bottom to the top of the bipod which is correct to their posted statement but the true and most important height of that same bipod is actually 8-1/8" to 11-7/8" on plumb.
            It would be most helpful if the manufactures would post "plumb" heights along with leg extension heights.
            not sure i understand the issue you're having.
            low table or tall chair? cut the legs.
            are you driving the rifle, or trying to shoot sitting up straight?

            it would help to know what rifle and type of shooting.

            Last edited by theLBC; 07-09-2019, 11:24 PM.

            Comment

            • #7
              vintagearms
              Calguns Addict
              • Jan 2009
              • 6841

              Either the Harris or Atlas CAL work for me and I am over 6'2" with long arms.

              FYI, the legs should fold towards the muzzle end and you load it pushing the rifle, not pulling back.

              Here are a couple videos that might be helpful:



              Comment

              • #8
                etwinam
                Veteran Member
                • Mar 2016
                • 3223

                I have a harris and its great. Atlas are solid but heavier.
                God, Guns & Integrity. Prioritize your Priorities.

                Comment

                • #9
                  Mandingo27
                  Senior Member
                  • Dec 2017
                  • 776

                  Get an atlas bipod

                  Comment

                  • #10
                    Mute
                    Calguns Addict
                    • Oct 2005
                    • 8609

                    Are you putting your elbows on the bench and therefore needing to set your rifle higher up off the bench? If that's your situation and you're mainly shooting off a bench, you may be better off getting a sled or a rest.
                    NRA Benefactor Life Member
                    NRA Certified Pistol, Rifle, Personal Protection In The Home, Personal Protection Outside The Home Instructor, CA DOJ Certified CCW Instructor, RSO


                    American Marksman Training Group
                    Visit our American Marksman Facebook Page

                    Comment

                    • #11
                      ar15barrels
                      I need a LIFE!!
                      • Jan 2006
                      • 57200

                      Originally posted by sfarchitect
                      My personal bipod pet peeve is spring loaded legs, I hate(!) 'em.
                      You build your position, get on the gun, line up your sites, try to load the bipod and SPROING! the bipod leg or legs fold and collapse.
                      This is indeed a problem when bipod is installed BACKWARDS!

                      Targets are also VERY DIFFICULT to see through a scope that is installed backwards.

                      I bet you shoot an HK pistol.

                      Last edited by ar15barrels; 07-10-2019, 11:46 AM.
                      Randall Rausch

                      AR work: www.ar15barrels.com
                      Handguns: www.handgunbarrels.com
                      Bolt actions: www.700barrels.com
                      Foreign Semi Autos: www.akbarrels.com
                      Most work done while you wait on a scheduled shop visit.

                      Comment

                      • #12
                        nickel plate
                        Senior Member
                        • Jul 2012
                        • 2148

                        smitty, It's a Harris HBLS Combo that includes a 9" to 13" bipod, an "S" lever for tightening the tilt and an RBA-1 rotating picatinny rail block so yes it does meet your suggestion. The RBA-1 also added another inch which got me into favorable height requirements.

                        sfarchitect, Have you contacted your bipod manufacturer and explained the spring loaded leg malfunction your having? I'd ask for a full refund.

                        My inital post was about what I found out height/measurement wise during pre-purchase research. My Ruger 583 Mini-14 now sports a Harris bipod hung off of a Magpul picatinny rail. I target shoot, plink and trunk gun it so please spare me the accuracy unworthiness of this rifle as this is not what this thread is about.
                        A couple photos of the finish product along with my home built collapsible legged portable shooting table and cut down/reinforced kitchen island bar stool.
                        Last edited by nickel plate; 09-05-2020, 8:57 AM.

                        Comment

                        • #13
                          RobG
                          Veteran Member
                          • Dec 2006
                          • 4887

                          Originally posted by sfarchitect



                          My personal bipod pet peeve is spring loaded legs, I hate(!) 'em. You build your position, get on the gun, line up your sites, try to load the bipod and SPROING! the bipod leg or legs fold and collapse.
                          Pro tip!: Attach the bipod correctly and it won't collapse under loading

                          Comment

                          • #14
                            Milsurp1
                            Veteran Member
                            • Aug 2016
                            • 3091

                            AccuTac makes great bipods.

                            Comment

                            • #15
                              onelonehorseman
                              Veteran Member
                              • Oct 2012
                              • 4888

                              Harris bipods are very good, as are those made by Atlas.

                              Installed correctly, they will get the job done nicely.
                              sigpic

                              Comment

                              Working...
                              UA-8071174-1