Unconfigured Ad Widget

Collapse

Delete

Collapse
This topic is closed.
X
X
 
  • Time
  • Show
Clear All
new posts
  • EvoXguy
    Senior Member
    • Oct 2015
    • 731

    Yeah, I think I'll stick with good ol fashioned cleaning rods. GL op, hope you get it fixed.
    Peace through superior firepower

    Comment

    • ER308
      Member
      • Jan 2013
      • 135

      fill bore with as much FFF black powder as you can stuff in there, and set it off with cannon fuse. blackpowder pressures should be way below the barrel proof limit. use a long fuse and run like hell after you light it. Oh... and do it outside in a ditch.

      Comment

      • RTE
        Senior Member
        • May 2009
        • 1948

        I'll check back when the smith gets done with it, until then.

        Calguns MARKETPLACE
        .223 Wylde barrel...low round count.

        I looked but couldn't find that video of a smith removing a slug from a barrel with grease and pressure.

        Comment

        • Cokebottle
          Señor Member
          CGN Contributor - Lifetime
          • Oct 2009
          • 32373

          I'm wanting to see the grease splatter on the ceiling when OP fills his barrel with wheel bearing grease and then slaps a cleaning rod with a hammer
          - Rich

          Originally posted by dantodd
          A just government will not be overthrown by force or violence because the people have no incentive to overthrow a just government. If a small minority of people attempt such an insurrection to grab power and enslave the people, the RKBA of the whole is our insurance against their success.

          Comment

          • Carsgunsandchics
            Veteran Member
            • Mar 2009
            • 3537

            Originally posted by Pardini
            If you look in the muzzleloaders section online or LGS you can get a patch worm and screw it on to a cleaning rod to grab the snake from the breech end. Not sure if they come in a small enough diameter to fit the bore though.
            Same thing I was thinking. Then came across your response. It'd probably fit into the chamber, if not find one for a 32 cal
            Originally posted by fighterpilot562
            I am more of a sucker than a blower...

            Comment

            • AAShooter
              CGN/CGSSA Contributor
              CGN Contributor
              • May 2010
              • 7188

              CO2 discharger?

              Comment

              • bodger
                Calguns Addict
                • May 2009
                • 6016

                Well....I think we've about covered this one. Very entertaining. I especially liked the appearance of the busted up wooden dowel rod sticking out of the barrel.

                Comment

                • Mayor McRifle
                  Calguns Addict
                  • Dec 2013
                  • 7798

                  Originally posted by bodger
                  Well....I think we've about covered this one.
                  Not quite. I don't think the OP has tried filling the barrel with shampoo and hot fudge yet.
                  Anchors Aweigh

                  sigpic

                  Comment

                  • HkUSP45
                    Senior Member
                    • Jan 2006
                    • 645

                    now he needs to get the chamber side stuck with a wooden dowel to balance out the Rifle.

                    Comment

                    • jmunks
                      Junior Member
                      • Feb 2012
                      • 44

                      This thread has been hilarious to read

                      Comment

                      • Michael777
                        Senior Member
                        • Apr 2016
                        • 894

                        Buy new barrel.

                        Comment

                        • ocabj
                          Calguns Addict
                          • Oct 2005
                          • 7924

                          This thread is going to be cited by all the guys who claim that cleaning guns is bad because you can damage your gun.

                          Imma just sit here with my Pro-Shot cleaning rod and Lucas bore guide...

                          Distinguished Rifleman #1924
                          NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
                          NRL22 Match Director at WEGC

                          https://www.ocabj.net

                          Comment

                          • Bad Andy
                            Junior Member
                            CGN Contributor
                            • Jun 2016
                            • 97

                            Try some KY. Should just slide in and out after that.

                            Comment

                            • Luky
                              Member
                              • Sep 2013
                              • 130

                              OP, All I can saw is "wow". I am about speachless.

                              Some constructive advise... First I would take the upper apart and remove the flash hider, gas block, etc so you have a bare barrel to work with. Then it was not clear to me if you have the brass bristles stuck in the barrel. If so, I would try to dissolve/weaken them using a high concentrate of ammonia as someone else had posted. Do this outside or in the garage due to toxic fumes. Hold the barrel upright and fill with lab grade concentrated ammonia (not the 3% solution you buy at the grocery store), maybe you can try sweets 7.62 for this step. let sit for a few days changing out the solution a couple of times. If it is dripping out the bottom that is good, if it is running out the bottom, plug it up with something (plastic) so it has time to work. After that, or if you don't have the brass bristles inside the barrel to start with: fill barrel with Kroil pentrating oil while in the vertical position so it can soak through this mess. After a day or two (watch for the Kroil to go all the way through and drip out the other side) you can try to push it out using a hydraulic press and a METAL rod like brass or copper AND I said press, not hammer. I would get several brass rods that are as tight to the bore diameter as possible (.220 or .200) and use short length sections that just stick out out of the barrel about 1"-2" to try pushing the obstruction out of the barrel an inch at a time. If you don't know somebody (machinist ) with the right tools to set this up in a hydraulic press and clamp on the outside of the barrel to press it out, you might just be better off buying a new barrel and learning from your mistake. I would be concerned that you have already FUBAR this barrel with your attempts. You may want to have the crown recut anyway when you are done unfu cking this barrel. (I didn't know this was such a nanny site to block out my text).

                              In the future get yourself a one piece carbon fiber cleaning rod and only use the correct size jag and patches to clean your barrel. Maybe a plastic bristle brush. Avoid the bronze brushes as they can cause unnecessary wear to your bore. Get yourself a bore guild and only clean from the breach to the muzzle. If you can't just press the patch through you have too much cloth/patch. Dont jam it or hammer it. And don't over clean your barrel. I used to make this mistake and now I am into precision rifles and only clean my barrel every 300-400 rounds when my groups start opening up. Let the cleaning solutions do their job. I simply use Hoppe's #9 and maybe some sweets 7.62 or kroil now and then and it's all I need. Find the cleaner that works for you. No bronze brushes, no scrubbing back and forth.

                              Good luck!
                              Last edited by Luky; 08-15-2016, 12:44 AM.

                              Comment

                              • 1bulletBarney
                                CGN/CGSSA Contributor
                                CGN Contributor
                                • Oct 2013
                                • 1918

                                800px-Cynictis_penicillata_mating1_cropped.jpg

                                They would deal with the snake but they are busy...
                                NRA Member
                                NRA-ILA Contributor
                                CGN Contributor

                                iTrader Feedback
                                1bulletBarney iTrader Feedback - Calguns.net?

                                Comment

                                Working...
                                UA-8071174-1