Unconfigured Ad Widget

Collapse

How to pattern a shotgun?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • kazman
    Senior Member
    • Apr 2009
    • 528

    How to pattern a shotgun?

    Just picked up a used beretta 20 ga sxs with full/modified (store guysaid improved/modified but says f/m on the barrel).
    Is the best way to pattern it to shoot it at paper at 25yards?
  • #2
    aippi
    Senior Member
    • Jun 2009
    • 2302

    The yardage should be the same yardage you anticipate shooting the shotgun and with the same shot size you intend to use. This way you know the pattern the weapon produces with that shot at that range.
    JD McGuire, Owner
    AI&P Tactical
    Remington Law Enforcement Armorer
    Mossberg LE Armorer
    www.aiptactical.com
    www.tacticalgunslings.com
    If you're going to a gun fight, take a shotgun. If you can't take a shotgun, don't go.

    Comment

    • #3
      Fjold
      I need a LIFE!!
      • Oct 2005
      • 23094

      There are choke checkers for sale which use different diameter rods that you can check your barrels with.

      The typical American choke designations of Full, Modified, Improved Cylinder and Skeet are based on the percentage of the shot they put into a 30" circle at 40 yards. These designations later evolved into measured constrictions of the bore by .035" for Full, .020' for Modified .0010" for Improved Cylinder and .005" for skeet. In other words, if your Browning has an internal barrel diameter of .729", an Improved Cylinder choke should have an internal diameter of .719" or ten thousandths of an inch of constriction.
      Frank

      One rifle, one planet, Holland's 375




      Life Member NRA, CRPA and SAF

      Comment

      • #4
        Revoman
        Senior Member
        • Dec 2007
        • 2394

        Yes, the best way to pattern is by using paper.

        Under the best circumstances, you should use a rest such as a car hood to take careful aim at a dot that you have made in the center of a large piece of paper, blueprints or butcher paper work well for this. There are also manufactured targets that will show a 30 inch diameter circle to make life a little easier.

        A 30 inch circle is the basis for patterning. You would divide the circle into four equal parts, kind of pie pieces if you will, then count each hole made by the shot to see where the greatest density is. This should indicate if there is good consistancy in the pattern or if there are issues with it. Most folks do not take it to this level however and the following is probably the most commonly used method:

        The yardage can vary as stated earlier, but in general between 20 and 25 yards would be a good base.

        You fire directly at the dot you made in the center of the paper, taking very careful aim, that's why it is important to have a sound base such as a car hood to help.

        Once you have fired a single round at the dot, unload your shotgun and go get the paper. You should see as you approach the paper some sort of pattern that may be centered (should be) or over/under or to either side of the dot.

        If bulk of the shot is pretty much equal around the dot, then the pattern should tell you that the shotgun is good to point of aim and point of impact.

        If it is high, that is not necessarily a bad thing as most shotguns are made to shoot slightly high as the game/target you are shooting should be seen just above the bead, it's rare that the target would be covered by the bead thus being able to see the target throughout the shot for finding it later (If hunting).

        If the bulk of the pattern is to one side or the other, that means that there will be some adjustments necessary to the barrels to fix that problem.

        Well below the dot, it will need fixing as well.

        Sometimes the fix is as simple as replacing a choke, sometimes the barrel/s need to be tweaked by a smith.

        You should shoot each barrel as instructed above to assure that both are within tolerance to each other. One barrel may shoot straight while the other may not.

        Some shotguns shoot what is termed as a 60/40, or a variety of other fractions, which means that 60 percent of the shot is above the dot and the other 40 is below, this is very common in the competitive games as those guns are very highly tuned. For the average guy, if the pattern is relatively close to center, or slightly above, that works rather well.

        As stated earlier, it is important to know where your shotgun shoots, it's like sighting in a new rifle, you wouldn't take it hunting without knowing where it shoots would you? A shotgun is the same, yet most never take the time to pattern them.

        Comment

        Working...
        UA-8071174-1