Unconfigured Ad Widget

Collapse

Benelli M2 Taran Tactical Problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bmin
    Junior Member
    • Apr 2020
    • 79

    Benelli M2 Taran Tactical Problem

    Hi,

    I bought this gun off someone at CG, however when I tried to disassemble to clean it, I couldn't remove the magazine. I tried putting some oil today to possibly help it, but it simply isn't budging.

    Any suggestions would be helpful! I called TTI earlier but wasn't able to get a hold of them.

    Here are pictures of it:



  • #2
    Master_Prestige
    Senior Member
    • Aug 2019
    • 1016

    Remove that clamp holding the barrel and mag tube first lol

    Comment

    • #3
      RandyD
      Calguns Addict
      • Jan 2009
      • 6673

      I assume you first removed the clamp. If not, then do so. It is possible that someone used loctite, which should not have been used. You may need to try some heat.
      sigpic

      Comment

      • #4
        SkyHawk
        I need a LIFE!!
        • Sep 2012
        • 23532

        remove the barrel clamp FIRST then the mag extension tube should unscrew. The extension nut and the extension tube will unscrew as one piece. You cannot turn just the nut while the assembly is installed on the gun.

        Last edited by SkyHawk; 07-27-2020, 12:13 PM.
        Click here for my iTrader Feedback thread: https://www.calguns.net/forum/market...r-feedback-100

        Comment

        • #5
          bmin
          Junior Member
          • Apr 2020
          • 79

          I guess that’s it, I’ll try it later. All the videos I found of disassembly were on stock M2’s not TTI.

          Thanks everyone!

          Comment

          • #6
            bmin
            Junior Member
            • Apr 2020
            • 79

            Anyone know what part I need to get to replace this booboo? (The marks from the visegrip tool)

            Comment

            • #7
              comandante costello
              Senior Member
              • Oct 2007
              • 523

              A new extension tube. Or a sharpie.

              Comment

              • #8
                SkyHawk
                I need a LIFE!!
                • Sep 2012
                • 23532

                Originally posted by bmin
                Anyone know what part I need to get to replace this booboo? (The marks from the visegrip tool)
                You can get just the nut from Nordic. Your old nut can be removed from the tube AFTER you have the tube assembly off the gun.
                This product adapts the MXT extension tube kit to your shotgun. Visit this page for information to ensure you order a complete kit assembly.


                maybe find it cheaper on ebay or a gun parts supplier. Here it is cheaper


                Otherwise just use a chemical touch up pen for aluminum
                Last edited by SkyHawk; 07-27-2020, 1:20 PM.
                Click here for my iTrader Feedback thread: https://www.calguns.net/forum/market...r-feedback-100

                Comment

                • #9
                  naz
                  Veteran Member
                  • Jun 2020
                  • 3108

                  You can buy Nordic tube only or extension nut only.

                  Why not just roll with it for now? If you’re going to use it for multigun it’s going to get thrown in buckets anyway.

                  Also, will you use it for trap? I keep the extension tube off mine most of the time since it adds more steps to cleaning, and you probably can’t load up the magazine anyway for that game

                  Comment

                  • #10
                    Powder_Keg
                    Senior Member
                    CGN Contributor
                    • Jan 2013
                    • 2203

                    +1 for the BIRCHWOOD CASEY - ALUMINUM BLACK

                    Comment

                    • #11
                      bmin
                      Junior Member
                      • Apr 2020
                      • 79

                      Last edited by bmin; 07-27-2020, 3:04 PM.

                      Comment

                      • #12
                        naz
                        Veteran Member
                        • Jun 2020
                        • 3108

                        Originally posted by bmin
                        Thanks a lot everyone! I feel kinda dumb, but in my little defense I took it to a gunsmith yesterday that also didn’t figure it out.

                        When I showed him the issue he said:

                        “That is kind of a crazy method for install no one else ever uses.”

                        I tend to agree with him as unless you have the tools you can let field strip this M2....
                        Hi op, the first bullet point in the benelli m2 manual for shotgun stripping is “slacken screw and remove the barrel magazine tube retaining ring (fig16) from its seat on the magazine tube (only in versions equipped with long magazine tube or with magazine tube extension”

                        If your gunsmith couldn’t figure that out, I respectfully suggest you go to another gunsmith in the future to service your m2

                        Also, you are right that you need a tool for that retaining ring. That’s why I keep the stock 3 shell tube when I don’t need the extra capacity, so save those steps, and to takedown the shotgun just by twisting off the ring

                        Comment

                        • #13
                          bmin
                          Junior Member
                          • Apr 2020
                          • 79

                          I purchased a Benelli M2 Left Handed 28" 12Ga in 2011 from dealer stock. Testing after full cleaning shows that it will not cycle with several 3 Dram factory target loads that I have. However it cycles just fine on the 2 3/4 Dram Remington Gun Club shells. 500 rounds later (to break it in) and...



                          Sent from my iPhone using Tapatalk

                          Comment

                          • #14
                            BajaJames83
                            Calguns Addict
                            • Jun 2011
                            • 6047

                            any and all shotguns with a clamp on the extension the clamp always needs to be removed first. you cant even take the barrel off without removing the clamp
                            NRA Endowment Life Member
                            USMC 2001-2012

                            Never make yourself too available or useful...... Semper Fidelis

                            John Dickerson: What keeps you awake at night?
                            James Mattis: Nothing, I keep other people awake at night.

                            Comment

                            • #15
                              SkyHawk
                              I need a LIFE!!
                              • Sep 2012
                              • 23532

                              Originally posted by bmin
                              Yes, I agree. Maybe his mind was elsewhere.
                              I originally went to him to check why the gun wasn’t recycling, I tried to disassemble to clean it, that’s when I ran into this.

                              I ordered parts based on this post:

                              I purchased a Benelli M2 Left Handed 28" 12Ga in 2011 from dealer stock. Testing after full cleaning shows that it will not cycle with several 3 Dram factory target loads that I have. However it cycles just fine on the 2 3/4 Dram Remington Gun Club shells. 500 rounds later (to break it in) and...



                              Sent from my iPhone using Tapatalk
                              If you ordered a new carrier latch, you will need to know if it will work with whatever oversize bolt release mechanism is on that Taran Benelli. The large button I use on my M1 requires the carrier latch button to be drilled and tapped, and it is easy to break the tack welds holding the original button when you do it if you are not careful and jigged up to isolate the button from the latch.

                              Better post a pic of the oversize button you have now, if you have one.

                              Also I would gamble that your existing latch was polished by Taran to make loading easier, and perhaps also fine tuned (by subtle bending). So all that will go out the window if you change the latch.

                              And yeah, that gunsmith

                              Originally posted by bmin

                              I tend to agree with him as unless you have the tools you cant field strip this M2....
                              The only tool you need is an allen wrench for the barrel clamp screws. And technically you could run without the clamp at all but it will be a more fragile setup.

                              You could also change out the allen head screws on the barrel clamp for screws with a large head with a slot that a 12ga shell rim could fit in to unscrew, if stripping in the field without tools is a real concern. But then you would not be able to attach the optional rail section to the clamp.
                              Last edited by SkyHawk; 07-27-2020, 5:08 PM.
                              Click here for my iTrader Feedback thread: https://www.calguns.net/forum/market...r-feedback-100

                              Comment

                              Working...
                              UA-8071174-1