Unconfigured Ad Widget

Collapse

Ithaca 37 20g

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Redneck Geek
    Senior Member
    • Jul 2012
    • 1002

    Ithaca 37 20g

    I just got an older Ithaca 37 in 20g. If I read the codes right it was made in 1949. It does have a Cutts compensator on it. (link below, scroll for vintage advertising).

    I racked it a few times, dry fired it, made sure the safety worked etc. before I bought it. It's in really decent condition, everything is tight, no obvious metal issues.

    My question is (and yes I realize it's an open-ended question)...is the thing safe to shoot? I'm really not sure what else to look for safety-wise. I have never shot a gun with a compensator (or a choke) either.

    Thanks in advance for any help/advice.

    Link to classic magazine ad:
    I came upon & bought an old model 1148 in 20 GA with cutts compensator choke system. The only choke available (on the gun) is a modified choke. I could not resist it because my Dad had a similar shotgun in 16 GA that I shot quite often as a kid. My question's are, for shooting clays is the...
    sigpic
  • #2
    P5Ret
    Calguns Addict
    • Oct 2010
    • 6406

    It should be ok, but I'd take it to a competent gunsmith for a detailed inspection, just to make sure. As far as the Cutts goes if the barrel is long enough I'd have that cut off and have it threaded for choke tubes, or see if I could located a barrel for it online. I don't know if the current version barrels will work on the older guns or not. Congrats on a nice old gun, that was one of the first shotguns I learned to hunt with.

    Comment

    • #3
      NapalmCheese
      Calguns Addict
      • Feb 2011
      • 5964

      So here's my take on it, just realize I am not a gunsmith, I just like old shotguns.

      Take the barrel off, ensure there's no cracks, check around the choke, make sure it's threaded down tight and is clean.

      Clean the bore, lube as needed. If you're feeling really plucky take the magazine apart and check and oil the spring, check the follower. Reassemble.

      Assuming all has gone well and everything looks on the up and up (that is no visible cracks in the metal) I'd shoot it. If there are cracks in the stock, you might want to address those before shooting. Shotguns run at pretty low pressure compared to handguns and rifles, but 11,000 psi is still a LOT of pressure. While the pressure is relatively low as firearms are concerned, the recoil is still quite stout and prone to breaking stocks if they are already cracked.

      Wipe everything down with an oily rag, rub some BLO on the wood, and enjoy your gun.

      BTW, the gunsmith at Diamond Gunsmithing, Les Hovencamp, was THE gunsmith at Ithaca for a very long while. He has stated any number of times in any number of forums that every Ithaca 37 made is okay to use with steel shot as long as the choke is MOD or more open. In the 20 gauge I would limit it to steel 4s at the largest, as 2s generally don't pattern well. Of course, I would opt to use something other than steel if I could (and I generally do) but if you go hunting some place and find that you left your ammo at home you can feel pretty secure in running to Wal-Mart and picking up a couple of boxes of steel 4s.

      If you feel a need to take your gun to a gunsmith, or want someone to work on it, Diamond Gunsmithing specializes in the older Ithacas.

      Is it a ribbed barrel? I really like the Ithacas as a field gun.
      Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

      Comment

      • #4
        NapalmCheese
        Calguns Addict
        • Feb 2011
        • 5964

        BTW, some people might chime saying you can get a different barrel.

        This is a half truth. Ithaca 37s of your vintage were hand fit/finished. While you can get a new barrel, you'll have to have it fit to your gun, and that is a pricey proposition. Newer 37s were built on more modern machines to more exacting tolerances and no longer need a hand fit barrel.
        Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

        Comment

        • #5
          Redneck Geek
          Senior Member
          • Jul 2012
          • 1002

          NC, yes it is a ribbed barrel. And P5, I got it from my LGS; they claim the gunsmith checked it out. I believe them.

          I really got it for my daughter to learn on. She's smaller in stature, so losing a bit of weight at the far end (by removing the Cutts) isn't a terrible idea.
          sigpic

          Comment

          • #6
            NapalmCheese
            Calguns Addict
            • Feb 2011
            • 5964

            Originally posted by Redneck Geek
            NC, yes it is a ribbed barrel. And P5, I got it from my LGS; they claim the gunsmith checked it out. I believe them.

            I really got it for my daughter to learn on. She's smaller in stature, so losing a bit of weight at the far end (by removing the Cutts) isn't a terrible idea.
            Before you cut anything, just an FYI that the ribbed barrels are more valuable and a factory Cutts on a ribbed barrel would sought after by some collectors. I don't know if they offered the Cutts from the factory for your date.

            If the serial number on the barrel has a choke marking, or a dash and a number (like xxxxxxx-1) then the barrel was choked from the factory and the Cutts is aftermarket. If there is no choke marking the cutts is likely factory done and I'd just as soon leave it, but that's just me.
            Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

            Comment

            • #7
              Redneck Geek
              Senior Member
              • Jul 2012
              • 1002

              Originally posted by NapalmCheese
              Before you cut anything, just an FYI that the ribbed barrels are more valuable and a factory Cutts on a ribbed barrel would sought after by some collectors. I don't know if they offered the Cutts from the factory for your date.

              If the serial number on the barrel has a choke marking, or a dash and a number (like xxxxxxx-1) then the barrel was choked from the factory and the Cutts is aftermarket. If there is no choke marking the cutts is likely factory done and I'd just as soon leave it, but that's just me.
              No dash-number anywhere, and only patent info on the Cutts itself. There is the word 'FULL' down near the stock so maybe that means 'full' choke.

              I found this too, and it indicates the thing is a 'Model 37 Repeater Pump' of a 'Standard Type.' That's interesting because there's also a 'Solid Ribbed' type but the serial number block is different than mine (which is 23nnnn). Do different types of ribbing exist?


              I should post a photo or two. Will do later.
              sigpic

              Comment

              • #8
                jl7422
                Member
                • Aug 2006
                • 420

                I'd leave the Cutts on it, but then I'm a fan of the Cutts. If you intend to have your daughter use it, the Cutts will certainly reduce the recoil and you can change-out the chokes on the front.

                Comment

                • #9
                  NapalmCheese
                  Calguns Addict
                  • Feb 2011
                  • 5964

                  Originally posted by Redneck Geek
                  No dash-number anywhere, and only patent info on the Cutts itself. There is the word 'FULL' down near the stock so maybe that means 'full' choke.

                  I found this too, and it indicates the thing is a 'Model 37 Repeater Pump' of a 'Standard Type.' That's interesting because there's also a 'Solid Ribbed' type but the serial number block is different than mine (which is 23nnnn). Do different types of ribbing exist?


                  I should post a photo or two. Will do later.
                  The FULL down near the (I'm assuming you meant) receiver is the choke designation. At some point they changed from the '-#' choke designator to a word designation. The Cutts is aftermarket. The rib may very well be aftermarket too. I don't recall, but I think you could get your 37 with a ventilated or solid rib. Does the rib have a manufacturer's name stamped on the side or top of it?
                  Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

                  Comment

                  • #10
                    OpticsPlanet
                    Vendor/Retailer
                    • Apr 2009
                    • 2129

                    NapalmCheese is exactly correct! I had an old twelve gauge from 1949 that my father-in-law gave me. It had a 30" full choke barrel which is pretty much useless these days. I investigated replacement barrels and found that they truly were hand fit and finished and that modern barrels did not work. I chose to have mine cut to about 25" and then added a PolyChoke (before choke tubes became real popular) and I took tons of game with that old gun!

                    George P.
                    CalGunners: Take 5% off your order of $50 or more at OpticsPlanet by using coupon code CALGUNS! Some exclusions apply.

                    OpticsPlanet
                    http://www.opticsplanet.com
                    Toll-Free (888) 504-7864
                    Send us a private message if we can be of help!

                    Comment

                    • #11
                      Redneck Geek
                      Senior Member
                      • Jul 2012
                      • 1002

                      Guessing this is a ventilated. Basically it's a solid piece welded/soldered/whatever onto the barrel with standoffs. 'Simmons Gun Specialties' is stamped on the side.



                      Yes, I meant receiver end.
                      sigpic

                      Comment

                      • #12
                        NapalmCheese
                        Calguns Addict
                        • Feb 2011
                        • 5964

                        Yuppers, that's a ventilated aftermarket Simmons rib. It was a pretty popular mod (along with the Cutts) for guns that came with a field barrel (that is, no rib and fixed choke).

                        From a collecting standpoint you're not going to do anything that will kill the value of the gun (collectors want originals and stuff). From a practicality standpoint the Cutts is useful in that it allows you to change chokes, reduces recoil (while increasing noise however), and puts the weight forward on the gun which can smooth out a jerky swing. The vented rib helps clean up your view down the barrel, but I can't say I notice much of a difference shooting with or without the rib since I'm too busy trying to remind myself to focus on the bird (I said I like shotguns, I never said I shoot them well....).

                        You can always cut down the barrel and send it off to Briley for screw chokes making the gun a little more pleasing to the eye and still affording the practicality of changeable chokes.

                        How long will the barrel be with the Cutts removed? For a youth gun I know Remington makes one with a 21 inch barrel that I've heard a few people like, other manufacturers stick to 26 or 24. Presumably the stock is still full sized (unless this was originally a youth gun)? You'll likely have to get that cut down as well.
                        Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

                        Comment

                        • #13
                          Redneck Geek
                          Senior Member
                          • Jul 2012
                          • 1002

                          It has the same contour from where it meets the receiver - but the LOP looks to be about an inch less than both my son's 16g Wingmaster, and my 12g Ithaca.
                          sigpic

                          Comment

                          • #14
                            NapalmCheese
                            Calguns Addict
                            • Feb 2011
                            • 5964

                            Originally posted by Redneck Geek
                            It has the same contour from where it meets the receiver - but the LOP looks to be about an inch less than both my son's 16g Wingmaster, and my 12g Ithaca.
                            It could have been a youth gun, or a ladies gun, or a smaller dude's gun. Or it could be someone bought it for their wife or daughter and gave it a few upgrades. Ithaca currently espouses that they have a ladies specific fit for their ladies model. I'm not sure what the difference is in the stock or when that started, so it may be that this one has been cut down.
                            Last edited by NapalmCheese; 04-23-2015, 4:19 PM.
                            Calguns.net, where everyone responding to your post is a Navy Force Delta Recon 6 Sniperator.

                            Comment

                            • #15
                              Redneck Geek
                              Senior Member
                              • Jul 2012
                              • 1002

                              Range report. This thing is a lot of fun to shoot. I'll have to try some clays with it.
                              sigpic

                              Comment

                              Working...
                              UA-8071174-1