Unconfigured Ad Widget

Collapse

Dedicated .22LR Issues. Fail to Fire and Feed

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pluke the 2
    Senior Member
    • May 2012
    • 1926

    Dedicated .22LR Issues. Fail to Fire and Feed

    I got a brand new .22LR upper that had about a 50% failure rate. 95% of my failures was fail to feed while the other 5% was fail to fire where the primer and firing pin failed to fire the round.

    Upper is a .22 tactical solution upper. I did modify the fire control group to have a 3lb pull so I'll take the blame for the failure to fire...

    I used 2 types of ammo. Rem. Golden bullets and m22 high velocities Winchester and both types of ammo had about the same amount of failures.

    I used (4) different blackdog x factor magazines. 3 brandnew and 1 used.

    I'll have to take pictures of the feed ramps.

    When the bullets went bang it was dam accurate... Unfortunately, it was inconsistent and not reliable.




  • #2
    pluke the 2
    Senior Member
    • May 2012
    • 1926

    Any ideas out suggestions would be greatly appreciated.

    Comment

    • #3
      pluke the 2
      Senior Member
      • May 2012
      • 1926

      Comment

      • #4
        Jet Setter
        Calguns Addict
        • Aug 2012
        • 5348

        I have a M4-22 upper and it has been flawless. However, when speaking with the manufacturer, they strongly suggest not using Golden Bullets - EVER.

        It seems that you might have a follower issue. Check out the Blackdog site. They have an explanation about followers and reliability. If you call them, they will send you different followers for free. They are a great company.

        Also, might bee good to polish the feed ramp just in case. Hope things get sorted out for you.
        *********************
        WTS:
        1. PW 800+ Hydro Multispeed (just the hydraulic unit that also works with Spolar press)
        2. PW 800B converted to 800C (12 gauge) with lots of accessories and upgrades
        3. Hornady 366 (12 gauge)

        Comment

        • #5
          pluke the 2
          Senior Member
          • May 2012
          • 1926

          Thanks for the tip. I'll try polishing. Is it recommended to polish the bolt carrier group as well as the feed ramps?

          Comment

          • #6
            pluke the 2
            Senior Member
            • May 2012
            • 1926

            And do you think i have an issue with all the black dog magazines? I was using 10 round short bodies. Just seems odd that all of them had the same amount of inconsistency.

            Comment

            • #7
              brassburnz
              Veteran Member
              • Nov 2006
              • 3553

              Here's your solution.



              I built a new dedicated .22 upper and I was getting FTF and FTF from every Black Dog magazine I used. I took the Taccom plug out of my other upper and placed it in this one. All problems gone, except for the fact I had to order another plug.
              NRA Life Member
              CRPA Life Member

              Comment

              • #8
                pluke the 2
                Senior Member
                • May 2012
                • 1926

                Alright I'm back... I got the better ammo out.



                From left to right. SK Ammo, Lightning, Federal, Blazer.

                (5) Magazines.
                50 Rounds

                SK ammo, 10 rounds, 1 FTFire, 1 FTFeed
                Lightning, 10 rounds, no issues.
                Federal, 10 rounds, no issues.
                Blazer, 10 rounds, 1 FTFire.

                So what I'm going to summarize here is that Rem Golden Bear and Winchester Super X sucks ******* in my picky .22 dedicated.

                Comment

                • #9
                  pluke the 2
                  Senior Member
                  • May 2012
                  • 1926

                  Comment

                  • #10
                    pluke the 2
                    Senior Member
                    • May 2012
                    • 1926

                    And the golden *****es that failed to feed and fire.

                    Comment

                    • #11
                      rdubya
                      Member
                      • Oct 2009
                      • 145

                      My Tac Sol upper shot anything and everything for the first 4-5k rnds. Even 22 longs (not long rifle) then I started to have FTF and FTE I even had a few ignition with the bolt not completly in battery.
                      I called TS and they sent me a new bolt, this was about 2 years ago. All was great for a while then it started to act up again. Got a rebuild/repair kit for the bolt from TS and worked pretty good for awhile.
                      Started acting up again and read about polishing the feed ramps and breech face with Flitz. I didn't have any so I took some real lite polishing compound and an AR cleaning brush, the one with the large bristles for cleaning the breech face. Put it on a rod and hooked it up to a drill and on very slow speed cleaned the breech. Be careful due to the material it is made of.
                      Seems to have stopped the FTF. Make sure the breech face is real clean that should help with the FTF and keep the bolt lubed good and wet also.

                      Comment

                      • #12
                        Triad
                        Senior Member
                        • Mar 2008
                        • 1685

                        Make sure the trigger springs are installed correctly. Invest in the Tacops buffer tube plug and depending on the finish, run it wet.

                        I had fits with my upper for a while but my trigger springs were installed incorrectly and once I put my buffer plug in, and reinstalled the trigger springs correctly its run like a sewing machine.

                        Comment

                        • #13
                          Eljay
                          Veteran Member
                          • Oct 2005
                          • 4985

                          The plug's definitely worth getting. Also these things just have to wear in to a certain extent. Shoot it for a while with whatever ammo works, clean and lube it after each range session, and then after a coupe of sessions re-evaluate the ammo. I kept finding that more and more types worked, and some of the ones that were most accurate wouldn't run at all initially but worked fine after 500 rounds.

                          Comment

                          • #14
                            tanakasan
                            Senior Member
                            • Oct 2011
                            • 1638

                            ^^This for sure!

                            Things will wear in after a brick or so. Be sure to keep things cleaned and lubed and get the Taccom plug.

                            As far as ammo, shoot what works. Looks like the Federal and Blazer are good for you. Remington GB are typically troublesome, although some say they run well in their specific arms.

                            You will still experience FTF, FTE...its the nature of the beast. The goal is as few as possible!

                            BTW, nice lookin' rig! Congrats!

                            Robert
                            WTB/WTT

                            Comment

                            • #15
                              NorCalDustin
                              Senior Member
                              • Apr 2010
                              • 1463

                              Originally posted by brassburnz
                              Here's your solution.



                              I built a new dedicated .22 upper and I was getting FTF and FTF from every Black Dog magazine I used. I took the Taccom plug out of my other upper and placed it in this one. All problems gone, except for the fact I had to order another plug.
                              Actually get the Reliability kit: http://taccom3g.com/22RF_RELIABILITY_KIT.html

                              The plug helps with Failure to Fire, Feed, and Extraction... The Firing pin helps with the Failure to Fire (it does wonders)... and the Extractor is really helpful in helping the gun run when it starts to get a little dirty OR if you end up with some really horrible ammo.
                              Originally posted by BannedinBritain
                              The only dumb question is the one you don't ask...and get arrested for later.

                              Comment

                              Working...
                              UA-8071174-1