Unconfigured Ad Widget

Collapse

Having problems zeroing my scope on my 10 22

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • marco1910
    Junior Member
    • Oct 2011
    • 35

    Having problems zeroing my scope on my 10 22

    Hi

    I mounted a Simmons scope on my 10 22 and took it to my near by indoor range to zero. At 25 yards my shots were down and left and it seemed to me that the windage and height controls did not give me enough adjustment to move my patterns up and to the right to zero the target. I spent an hour and could not get it. I'm a total beginner, never zero'd a rifle by myself. I was not prone and the shooting position was not the best but I'm wondering if My mount is that far off? Does that happen?

    I modified my ruger by swapping in a tapco stock, added a low profile utg mount and accushot profile rings

    I'm going to go back to the range next week and give it a shot but any guidance would be greatly appreciated. I want to get the rifle zero'd before I go do appleseed in April

    Thanks
  • #2
    Izzy43
    CGSSA Rimfire Coordinator
    • Dec 2009
    • 2670

    Did you shoot the rifle with iron sights? Was it pretty accurate then? After you answer this then more ideas can be pondered. Such as could be the mount, could be the rings, could be the scope, could be the barrel or receiver. So lets start at the beginning and go one step at a time.

    Comment

    • #3
      BrianRodela
      Senior Member
      • Jun 2010
      • 607

      Marco, it may be the excess play that comes from the OEM mount from Ruger. If the mount holes are a little larger than the screws, this may allow for excessive play when you tighten them down. Be sure to use a threadlocking compound on the screws when tightening. If all seems good, the last thing I would suspect would be the scope but it can happen.
      sigpic
      Genuine MMCS, Firefighter and father of two great kids!

      Comment

      • #4
        Barry
        Member
        • Nov 2003
        • 193

        Scope

        "might" be turning the knobs the wrong way.

        Although I might be telling you the obvious. I'll risk it.

        Here is how to adjust a scope.

        1. Place gun on a rest or sandbags.
        2. Adjust gun on rest, so corsairs are in the middle of the target.
        3. Fire gun. Note impact of bullet.
        4. Adjust gun on rest, so corsairs are in the middle of the target as before.
        5. Without moving the gun on the rest, adjust scope so corsairs are on the bullet impact.

        This will get you really close to adjusted with a minimum of shots. And should you turn the scope the wrong way you will see it immediately.

        As a last thought, check that your new stock is not placing pressure on the barrel and forcing it to one side.

        Hope that helps

        Barry

        Comment

        • #5
          edwardm
          Senior Member
          • Oct 2005
          • 1939

          Originally posted by marco1910
          Hi

          I mounted a Simmons scope on my 10 22 and took it to my near by indoor range to zero. At 25 yards my shots were down and left and it seemed to me that the windage and height controls did not give me enough adjustment to move my patterns up and to the right to zero the target. I spent an hour and could not get it. I'm a total beginner, never zero'd a rifle by myself. I was not prone and the shooting position was not the best but I'm wondering if My mount is that far off? Does that happen?

          I modified my ruger by swapping in a tapco stock, added a low profile utg mount and accushot profile rings

          I'm going to go back to the range next week and give it a shot but any guidance would be greatly appreciated. I want to get the rifle zero'd before I go do appleseed in April

          Thanks
          Pull the action out of the stock and check the tightness of the v-clock and allen screws that hold the barrel to the receiver. Mine were loose and the barrel would wobble, meaning I couldn't zero the rifle to save my life.

          Comment

          • #6
            JNunez23
            Veteran Member
            • Jan 2012
            • 2755

            Where are you located?
            sigpic"Be more concerned with your character than your reputation, because your character is what you really are, while your reputation is merely what others think you are."
            John Wooden

            Need a holster?, please email us at StrappedKydex@gmail.com for any holsters, mag carriers, and more. Custom jobs welcomed!

            Comment

            • #7
              CSACANNONEER
              CGN/CGSSA Contributor - Lifetime
              CGN Contributor - Lifetime
              • Dec 2006
              • 44094

              Originally posted by JNunez23
              Where are you located?
              My question too.
              NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
              California DOJ Certified Fingerprint Roller
              Ventura County approved CCW Instructor
              Utah CCW Instructor


              Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

              sigpic
              CCW SAFE MEMBERSHIPS HERE

              KM6WLV

              Comment

              • #8
                marco1910
                Junior Member
                • Oct 2011
                • 35

                thanks so much for the responses...I'll try and answer questions:

                1. Did not try the iron sights. I'm near sighted so I went for the scope, mounted and went to the range.
                2. I'm located near LAX (south bay).
                3. it was also recommended I buy a bore sigher?. I was able to get on paper but it was low and to the left...the other recommendation was to start at about 10 yrds first.
                4. I played around with the windage/height knobs even turning to the max and it did not seem to move it "a lot"..always to the left..again I was standing up, with the rifle resting on a support...I was at LAX firing range (if anyone knows where that is)

                Thanks
                Mark

                Comment

                • #9
                  JNunez23
                  Veteran Member
                  • Jan 2012
                  • 2755

                  Well you got on paper, that's a start.
                  sigpic"Be more concerned with your character than your reputation, because your character is what you really are, while your reputation is merely what others think you are."
                  John Wooden

                  Need a holster?, please email us at StrappedKydex@gmail.com for any holsters, mag carriers, and more. Custom jobs welcomed!

                  Comment

                  • #10
                    sholling
                    I need a LIFE!!
                    CGN Contributor
                    • Sep 2007
                    • 10360

                    Originally posted by Barry
                    "might" be turning the knobs the wrong way.

                    Although I might be telling you the obvious. I'll risk it.

                    Here is how to adjust a scope.

                    1. Place gun on a rest or sandbags.
                    2. Adjust gun on rest, so corsairs are in the middle of the target.
                    3. Fire gun. Note impact of bullet.
                    4. Adjust gun on rest, so corsairs are in the middle of the target as before.
                    5. Without moving the gun on the rest, adjust scope so corsairs are on the bullet impact.

                    This will get you really close to adjusted with a minimum of shots. And should you turn the scope the wrong way you will see it immediately.

                    As a last thought, check that your new stock is not placing pressure on the barrel and forcing it to one side.

                    Hope that helps

                    Barry
                    ^This is great advice^. The things to be aware of are that it's not uncommon for the rail mounting holes in the receiver to have been drilled at an angle to the barrel. The only workaround for that is expensive offset rings like Burris Signature Zee with their optional offset inserts. You may also have a loose scope, or it could be a bad scope which isn't uncommon with cheap scopes.
                    Last edited by sholling; 03-18-2012, 4:32 PM.
                    "Government is the great fiction, through which everybody endeavors to live at the expense of everybody else." --FREDERIC BASTIAT--

                    Proud Life Member: National Rifle Association, the Second Amendment Foundation, and the California Rifle & Pistol Association

                    Comment

                    • #11
                      CSACANNONEER
                      CGN/CGSSA Contributor - Lifetime
                      CGN Contributor - Lifetime
                      • Dec 2006
                      • 44094

                      Originally posted by Barry
                      "might" be turning the knobs the wrong way.

                      Although I might be telling you the obvious. I'll risk it.

                      Here is how to adjust a scope.

                      1. Place gun on a rest or sandbags.
                      2. Adjust gun on rest, so corsairs are in the middle of the target.
                      3. Fire gun. Note impact of bullet.
                      4. Adjust gun on rest, so corsairs are in the middle of the target as before.
                      5. Without moving the gun on the rest, adjust scope so corsairs are on the bullet impact.

                      This will get you really close to adjusted with a minimum of shots. And should you turn the scope the wrong way you will see it immediately.

                      As a last thought, check that your new stock is not placing pressure on the barrel and forcing it to one side.

                      Hope that helps

                      Barry
                      Yep, with this meathod it only takes one shot to zero an optic at any given distance.
                      NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                      California DOJ Certified Fingerprint Roller
                      Ventura County approved CCW Instructor
                      Utah CCW Instructor


                      Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                      sigpic
                      CCW SAFE MEMBERSHIPS HERE

                      KM6WLV

                      Comment

                      • #12
                        marco1910
                        Junior Member
                        • Oct 2011
                        • 35

                        Originally posted by Barry
                        "might" be turning the knobs the wrong way.

                        Although I might be telling you the obvious. I'll risk it.

                        Here is how to adjust a scope.

                        1. Place gun on a rest or sandbags.
                        2. Adjust gun on rest, so corsairs are in the middle of the target.
                        3. Fire gun. Note impact of bullet.
                        4. Adjust gun on rest, so corsairs are in the middle of the target as before.
                        5. Without moving the gun on the rest, adjust scope so corsairs are on the bullet impact.

                        This will get you really close to adjusted with a minimum of shots. And should you turn the scope the wrong way you will see it immediately.

                        As a last thought, check that your new stock is not placing pressure on the barrel and forcing it to one side.

                        Hope that helps

                        Barry
                        ok..thanks I got it..key is to adjust the scope to the bullet impact..I will try it again next week at the range...thanks

                        Comment

                        • #13
                          KTM RICK
                          Senior Member
                          • Mar 2011
                          • 564

                          Best 68$ I ever spent. Saved me hours and a lot of money on sighting in my rifles and my freinds rifles. Me and my buddys went in on it so the cost was minimal. http://www.leupold.com/tactical/prod...d-boresighter/

                          Comment

                          Working...
                          UA-8071174-1