Unconfigured Ad Widget

Collapse

Feed ramp - Can it cause FTF

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • energizer
    Senior Member
    • Jun 2010
    • 592

    Feed ramp - Can it cause FTF

    Hi,

    I have a browning challenger 3 that has a dent on the feed ramp. Could that be causing failure to feed?

    Thanks.

    Attached Files
  • #2
    Noobert
    Veteran Member
    • Jan 2009
    • 3343

    Are you experiencing FTFs?
    (\__/)
    (='.'=)
    (")_(") Copy and paste this bunny into your signature to help him gain world domination.!!!

    Comment

    • #3
      energizer
      Senior Member
      • Jun 2010
      • 592

      Yes, I get a FTF every 2-3 rounds.

      Originally posted by Noobert
      Are you experiencing FTFs?

      Comment

      • #4
        Scratch705
        I need a LIFE!!
        • May 2009
        • 12537

        then yes? why don't you get that dent out then see.
        Originally posted by leelaw
        Because -ohmigosh- they can add their opinions, too?
        Originally posted by SoCalSig1911
        Preppers canceled my order this afternoon because I called them a disgrace... Not ordering from those clowns again.
        Originally posted by PrepperGunShop
        Truthfully, we cancelled your order because of your lack of civility and your threats ... What is a problem is when you threaten my customer service team and make demands instead of being civil. Plain and simple just don't be an a**hole (where you told us to shove it).

        Comment

        • #5
          energizer
          Senior Member
          • Jun 2010
          • 592

          I did some internet research and found that polishing the feed ramp with a 600+ grit sandpaper would do the job.

          Does it sound right?

          Thanks

          Originally posted by Scratch705
          then yes? why don't you get that dent out then see.

          Comment

          • #6
            DirtNapKing
            Member
            • Oct 2009
            • 389

            If the pin is just kissing the rim then maybe your feed ramp is not the issue. Take it to a gunsmith before you sand the ramp. If the shell is failing to fire it obviously made it into the chamber and is no longer in contact with the feed ramp. Advising folks to polish the the ramp in some cases is like telling people to run super unleaded in there Pinto.

            Comment

            • #7
              Noobert
              Veteran Member
              • Jan 2009
              • 3343

              In this case, FTF is failure to feed, not fire
              (\__/)
              (='.'=)
              (")_(") Copy and paste this bunny into your signature to help him gain world domination.!!!

              Comment

              • #8
                energizer
                Senior Member
                • Jun 2010
                • 592

                Indeed it is failure to feed not failure to fire. When the failure happens I see that the cartridge is stuck before the chamber with the tip stuck at 12' o clock. This failure also damages the cartridge tip at 12'o clock.

                I'll try to find a picture that I took some time ago.

                Thanks.

                Comment

                • #9
                  barrym66
                  Senior Member
                  • Mar 2009
                  • 2228

                  Don't just blindly sand away with sheet sandpaper using your fingers - you should use a suitably shaped (rounded) sanding pad/dowel as a backing for the emery cloth/paper, or ideally a rotary tool and some polishing compound.

                  Is it FTF'ing on flat nose or hollow point bullets? That a pretty rough looking ramp and the ding looks like it could catch on the edge of anything but a rounded nose bullet.

                  Good luck and report back with your results!
                  Barry

                  sigpic

                  "Environmentalists look at the gun, the car and the jet engine as instruments of Satan, but the mosquito has killed more than all three put together." Jeremy Clarkson, on the green movement

                  Thomas Jefferson

                  Comment

                  • #10
                    DirtNapKing
                    Member
                    • Oct 2009
                    • 389

                    Originally posted by Noobert
                    In this case, FTF is failure to feed, not fire
                    Whoopsy I swaped threads up with the kid that had the green mountain barrel issue and fail to fires. My bad! Polish away!!!!!!!!!!

                    Comment

                    • #11
                      energizer
                      Senior Member
                      • Jun 2010
                      • 592

                      I saw a you tube video where the guy used pencil's eraser tip on sandpaper to polish the ramp.

                      http://www.youtube.com/watch?v=2yahzMTOO34">http://www.youtube.com/watch?v=2yahzMTOO34" type="application/x-shockwave-flash" width="425" height="350">

                      I have a dremel tool but I'm not adept at it. What polish tool should I use? I believe that I have a small quantity of polish compound that came with dremel.

                      It is failing with the Remington Golden Bullet hollow points and CCI Stingers.

                      Originally posted by barrym66
                      Don't just blindly sand away with sheet sandpaper using your fingers - you should use a suitably shaped (rounded) sanding pad/dowel as a backing for the emery cloth/paper, or ideally a rotary tool and some polishing compound.

                      Is it FTF'ing on flat nose or hollow point bullets? That a pretty rough looking ramp and the ding looks like it could catch on the edge of anything but a rounded nose bullet.

                      Good luck and report back with your results!


                      These abbreviations can be very interchangeable

                      Originally posted by DirtNapKing
                      Whoopsy I swaped threads up with the kid that had the green mountain barrel issue and fail to fires. My bad! Polish away!!!!!!!!!!

                      Comment

                      • #12
                        energizer
                        Senior Member
                        • Jun 2010
                        • 592

                        Another look at feed ramp

                        Attached Files

                        Comment

                        • #13
                          Noobert
                          Veteran Member
                          • Jan 2009
                          • 3343

                          Just remembered Box o Truth did a polishing job with a polishing bob and a Dremel



                          First post of 2011!
                          (\__/)
                          (='.'=)
                          (")_(") Copy and paste this bunny into your signature to help him gain world domination.!!!

                          Comment

                          • #14
                            barrym66
                            Senior Member
                            • Mar 2009
                            • 2228

                            Originally posted by energizer
                            I saw a you tube video where the guy used pencil's eraser tip on sandpaper to polish the ramp.

                            I have a dremel tool but I'm not adept at it. What polish tool should I use? I believe that I have a small quantity of polish compound that came with dremel.
                            Wrap some 600 to 800 grit wet-or-dry sandpaper around a round dowel or other non-metal shape about 3-4" long. Wet the paper and lightly sand the rough surface of the ramp in a longitudinal (back and forth) motion as well as a rotating motion. You want to smooth out the burrs and scratches, being careful to not remove excess material and/or change the basic shape of the ramp. Use plenty of light oil and wash away the metal particles (will look like black dirt) frequently. WD-40 works well for this.

                            Once smooth, wipe off the excess oil and wash well with solvent. Use a 3/8" to 1/2" diameter felt polishing wheel in the Dremel at medium speed with a medium to fine abrasive compound and some drops of water - if you don't have any polishing rouge or compound handy, try using a water slurry of Ajax or Comet cleanser and change/renew frequently. Polish with light to medium pressure until the ramp is shiny and bright.

                            Use eye protection with the Dremel and do it outside as the Dremel will sling some of the dirty compound around if you get it too 'wet'.

                            There should be no rough edges or burrs in the surface of the ramp that can catch on a bullet...use your fingernail to check.

                            I have had to do this on various aftermarket Glock and CZ barrels over the years, as well as to help feeding on a stock SA 1911 that had issues with hollowpoints. It has always helped when running into feed issues (assuming mags and all other potential FTF causes etc. were OK).

                            Have fun and good luck - and have a Happy New Year!
                            Barry

                            sigpic

                            "Environmentalists look at the gun, the car and the jet engine as instruments of Satan, but the mosquito has killed more than all three put together." Jeremy Clarkson, on the green movement

                            Thomas Jefferson

                            Comment

                            • #15
                              energizer
                              Senior Member
                              • Jun 2010
                              • 592

                              Thanks,

                              I'll go through the link. BTW, I still have 2 1/2 hrs to go for the new years post ;-)

                              Originally posted by Noobert
                              Just remembered Box o Truth did a polishing job with a polishing bob and a Dremel



                              First post of 2011!

                              Comment

                              Working...
                              UA-8071174-1