Unconfigured Ad Widget

Collapse

Zero in a scope

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SammieT
    Banned
    • Mar 2014
    • 901

    Zero in a scope

    Is there a certain way to do this? I've tried plenty of times but I can't seem to get it right on the target. Is there something I'm missing? Something I didn't do? I need help with this big time. The scope I have is a 10-50x40 if you were wondering. .

    Thanks!
  • #2
    Jeepergeo
    Veteran Member
    • Feb 2012
    • 3507

    Make sure both the windage and elevation adjustments are centered. Then, if you have a bore sight laser, use that at 25 yards to make sure you are on paper, or fire a few shots to see where you are at. These initial steps are critical to helping you determine if the Scope to Gun mount is proper.

    Once on paper at 25 yards, move out to 50 or 100 yards and use the windage and elevation adjustments to zero.

    The above procedure is for a 22, but works for other long guns too. It has more to do with the scope to gun mount and centering the scope than anything. Once that is resolved, you can focus on zeroing at your preferred shooting distance.
    Benefactor Life Member, National Rifle Association
    Life Member, California Rifle and Pistol Association

    Comment

    • #3
      CSACANNONEER
      CGN/CGSSA Contributor - Lifetime
      CGN Contributor - Lifetime
      • Dec 2006
      • 44094

      don't waste time and ammo zeroing it close. Just pull the bolt, bore sight by looking down the barrel (don't waste your money on stupid laser sighters that are not as reliable as your eyes), add the approximate appropriate elevation for your load and distance then simply use the one shot zero method. Of course, you'll either need to run a few rounds to heat up your barrel first of do a cold bore zero and wait a while between shots. Yes, it is simple to start with an unzeroed scope and put your second shot in the ten ring (if not the x ring) at any distance you can consistently shoot decent groups at.
      NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
      California DOJ Certified Fingerprint Roller
      Ventura County approved CCW Instructor
      Utah CCW Instructor


      Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

      sigpic
      CCW SAFE MEMBERSHIPS HERE

      KM6WLV

      Comment

      • #4
        Dinosaur Jr
        Senior Member
        • May 2012
        • 1707

        The "one-shot method" is actually two shots since you need to check your results...but it's the best way I've tried.

        Last edited by Dinosaur Jr; 06-08-2014, 11:55 AM.
        Laws against murder and attempted murder should have been the only gun control laws ever needed in America...

        Comment

        • #5
          CSACANNONEER
          CGN/CGSSA Contributor - Lifetime
          CGN Contributor - Lifetime
          • Dec 2006
          • 44094

          Originally posted by AKS-762
          The "one-shot method" is actually two shots since you need to check your results...but it's the best way I've tried.

          Yea, theoretically it is zeroed after one shot. I usually use a second shot to fine tune and a third for confirmation. But, if you do everything correctly, after one shot, it is zeroed. I had a 14 year old try this at 1000 yards and he was able to hit a clay pigeon on his third shot without "fine tuning" his second shot. He had only missed his second shot by about .2moa. Most people can't shoot that well in the first place.
          NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
          California DOJ Certified Fingerprint Roller
          Ventura County approved CCW Instructor
          Utah CCW Instructor


          Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

          sigpic
          CCW SAFE MEMBERSHIPS HERE

          KM6WLV

          Comment

          • #6
            sjb269
            Member
            • Nov 2011
            • 297

            SammieT,
            Back up a bit and ensure your optics are mounted correctly first.
            There are too many tutorials out there to list on how to do that properly.
            In oder to begin to have people help you here… take the time to explain in detail...
            1. Exactly what you are using for rifle/scope/rings/base
            2. What Methods you have tried already to zero
            3. Where you are located ( you could live in the same town as me for all I know) If that's the case, I'd be happy to help you in person.

            Comment

            • #7
              SammieT
              Banned
              • Mar 2014
              • 901

              1. Rifle is a savage model 10. 308 caliber. The mounts came with the scope. I'll get the brand name when I can and post it.

              2. Was using a laser bore sight to make the vertical and horizontal land in the center

              3. located in east county of San Diego area

              Comment

              • #8
                SammieT
                Banned
                • Mar 2014
                • 901

                Originally posted by Jeepergeo
                Make sure both the windage and elevation adjustments are centered. Then, if you have a bore sight laser, use that at 25 yards to make sure you are on paper, or fire a few shots to see where you are at. These initial steps are critical to helping you determine if the Scope to Gun mount is proper.

                Once on paper at 25 yards, move out to 50 or 100 yards and use the windage and elevation adjustments to zero.

                The above procedure is for a 22, but works for other long guns too. It has more to do with the scope to gun mount and centering the scope than anything. Once that is resolved, you can focus on zeroing at your preferred shooting distance.
                I tired at an indoor range. Haven't had the time to go all out desert wise to use the full scope at maximum length. I didn't think mounting would actually Made that much of a difference honestly

                I set it at 75 with a laser bore sight at first but it's always off by a couple of MM even though I get the laser to match up exactly with the scope

                Comment

                • #9
                  SammieT
                  Banned
                  • Mar 2014
                  • 901

                  scopebrandsightsgun
                  Last edited by SammieT; 06-08-2014, 12:53 PM.

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    Now I see your problem! Dump the stupid laser bore sighter and get quality rings and optics. I wouldn't out a Barska on my enemy's airsoft gun. After get a decent scope and rings (even a Simmons or BSA), let me know. If you can make it up to Angeles, I'll help you.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      ocabj
                      Calguns Addict
                      • Oct 2005
                      • 7924

                      Originally posted by SammieT
                      2. Was using a laser bore sight to make the vertical and horizontal land in the center


                      Distinguished Rifleman #1924
                      NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
                      NRL22 Match Director at WEGC

                      https://www.ocabj.net

                      Comment

                      • #12
                        sjb269
                        Member
                        • Nov 2011
                        • 297

                        OK, I am not gonna hammer you too hard…yet.
                        What is it your trying to accomplish with this set up?
                        What is your goal?
                        What are your accuracy parameters?

                        Comment

                        • #13
                          SammieT
                          Banned
                          • Mar 2014
                          • 901

                          Just trying to enjoy my life and live every day like it's my last

                          Be honest.. always wanted a sniper rifle. It's just got fun to go out and enjoy the outdoors and shoot whatever I see in the desert lol...

                          Is something wrong with my set up?

                          Comment

                          • #14
                            SammieT
                            Banned
                            • Mar 2014
                            • 901

                            I figured after watching that video someone posted. I'm just gonna dump it.

                            I just need to purchase a sandbag instead now

                            Comment

                            • #15
                              SammieT
                              Banned
                              • Mar 2014
                              • 901

                              Originally posted by CSACANNONEER
                              Now I see your problem! Dump the stupid laser bore sighter and get quality rings and optics. I wouldn't out a Barska on my enemy's airsoft gun. After get a decent scope and rings (even a Simmons or BSA), let me know. If you can make it up to Angeles, I'll help you.
                              Something wrong with the scope?

                              Comment

                              Working...
                              UA-8071174-1