Unconfigured Ad Widget

Collapse

Scope base ?s

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • anyracoon
    Veteran Member
    • May 2006
    • 3704

    Scope base ?s

    I just bought a Remington 700 SPS tactical in 308 and need some direction/questions answered as far as optics are concerned.

    What is the difference between a 0 MOA base & 20 MOA base?

    Should I go with steel or aluminum?

    I probally will be using a Armalite one piece scope mount so leaning towards a one piece rail.

    Probally will putting a Burris Black Diamond 8X - 32X scope.

    So what says the hive?
  • #2
    Iloveguns
    Senior Member
    • Mar 2009
    • 868

    Always go with the one piece unless you are trying to save weight. Rule of thumb for Steel vs Aluminum. Aluminum rings work on Aluminum or Steel bases. Steel rings work on Steel bases. Steel will chew up Aluminum bases. Do not recommend to do that. Do some research and try to learn about MOA (Minute of Angle). You will need to know what it is to understand how to use your scope. Go with the 20 MOA base as it will give you more elevation out of your scope.

    Comment

    • #3
      Whonu
      Junior Member
      • Nov 2012
      • 76

      What range do you intend to be shooting? The 20 MOA base is used for long yardage where your scopes internal mechanism won't give you enough range of MOA adjustments clicks.

      Comment

      • #4
        anyracoon
        Veteran Member
        • May 2006
        • 3704

        300 yards plus

        Comment

        • #5
          Whonu
          Junior Member
          • Nov 2012
          • 76

          Originally posted by anyracoon
          300 yards plus
          Unless you're regularly shooting past 800yrds you probably don't need the 20MOA base. You'll have to check how many MOA of adjustment your particular scope has. I'm just learning myself, so this is just what I've read. YMMV.

          Comment

          • #6
            FMJBT
            Veteran Member
            • Mar 2007
            • 4888

            I'd go for the 20 moa base regardless of distance. There really isn't a downside to getting a 20 moa base, and the cost is normally the same for both.
            U.S. Navy (Retired) 1994-2015

            Comment

            • #7
              postal
              Banned
              • Mar 2008
              • 4566

              Yeah.... pretty much what FMJ said.

              The difference is.... a flat base (0) or an angled base which points the scope downward slightly (10 or 20MOA)

              This is because *assuming* a scope zeros perfectly, it would be dead center, but you only use adjustment of the scope for elevation, raising the scope--- you only use 1/2 of the internal travel adjustments built into the scope.

              By angling the mount, pointing the scope down, your center will be offset, giving you more travel in elevation.

              This is primarily dependent on cartridge, distance, and the actual model of scope with internal adjustment available, if an angled base is actually REQUIRED, but they never hurt, so you may as well.

              Inside 600 yds, most scopes will be fine with a flat base. 800 plus, and smaller diameter scope tubes can run out of clicks, larger dia tubes usually have more adjustment and can still work, but there is only one downside of running an angled base, and that is--- usually the angled base is slightly taller than a flat one, which means you may need to use a cheek pad of some sort to get a proper cheek weld.

              Comment

              • #8
                Charlieh313
                Member
                • Nov 2010
                • 472

                Definitely go with the 20MOA base and agreed with the matching of materials for the scope rings and base

                Comment

                • #9
                  sjb269
                  Member
                  • Nov 2011
                  • 297

                  Um, just be sure you don't mount the 20MOA base backwards.
                  With an SPS tac, your prob. not worried about weight, I say go crazy... all steel. Course if your not gonna be knocking the rife around or humping it over mountain passes...AL is just fine too being a .308.

                  Comment

                  Working...
                  UA-8071174-1