Unconfigured Ad Widget

Collapse

Primary Arms Micro Dot Problem?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Res
    Senior Member
    • May 2006
    • 1633

    Primary Arms Micro Dot Problem?

    My PA Micro just came in the mail today. Opened and looked through it and saw this:




    This isn't normal is it? And the dot is not crisp at all. I didn't take a picture of it on, but with my awesome bitmap skills I can pretty much recreate it. Is this how PA red dots are supposed to be, or did I get a bad one?

    --------------------------------------------
    Dusty Miller
    Sacramento

    Matthew Jackson Miller: 8-6-07 to 10-15-07
    sigpic
  • #2
    H2H
    Senior Member
    • Jun 2005
    • 1663

    Dot should be much crisper. Send it back, they will replace it no charge.

    Comment

    • #3
      Res
      Senior Member
      • May 2006
      • 1633

      Okay. Contacted Marshall and he says it looks normal and recommended mounting it on the rifle and see how it looks. I'm thinking it was that fuzzy because I had it set on max in a dark room (this is my first red dot, would that make it look bad). It looks better set on 5 looking out in the backyard.

      But there is no way I can use this as 1/3 co-witness. It covers the complete right side of the front sight post and makes it a pain to even try to align it. It covers about a 1/4 of the rear peep at 5 o'clock. I emailed him again explaining this.

      boo
      --------------------------------------------
      Dusty Miller
      Sacramento

      Matthew Jackson Miller: 8-6-07 to 10-15-07
      sigpic

      Comment

      • #4
        Low-Pressure
        Senior Member
        • Sep 2009
        • 1758

        Marshall will take care of you. They have a great customer service policy. I bought a microdot and took me 4 months before I tried it out. Turns out the adjustment was installed incorrectly. After an e-mail, I was told to send it back. I received the replacement 2 days later, and I haven't even sent the defective one out yet. I'm saving up money for their PA scope for my next purchase.
        Good luck!!
        ...with liberty and justice for all. Void where prohibited, offer not valid everywhere, price may change. See Big Brother for details.
        Originally posted by zfields
        9mm might expand but .45 never shrinks!
        Originally posted by bwiese
        Constitutional rights are not dependent on your neighbors' opinions'.
        If you shop at Amazon.com please use the link below. A portion of your purchase goes to CGF.
        http://www.amazon.com/?_encoding=UTF...reative=390957

        Comment

        • #5
          Res
          Senior Member
          • May 2006
          • 1633

          Thanks Low. Is your "laser emitter" flush, or does it jut out like this one? I ask because Marshall said it looks normal in the picture. But at 1/3 cowitness I the right shroud of the front sight is completely covered as well as the lower part of the blade.

          --------------------------------------------
          Dusty Miller
          Sacramento

          Matthew Jackson Miller: 8-6-07 to 10-15-07
          sigpic

          Comment

          • #6
            Matt P
            Veteran Member
            • Jun 2006
            • 3101

            Yes Res, the bitmap force is strong with you.

            I checked 5 of the T-1 (Aimpoint) copies, with 3 being from different suppliers, and the light emitter in those is located at the six oclock position.
            This is not to say yours is wrong, just more of an observation in the ones I checked.

            If you turn up the intensity, you will notice blooming, and certainly have an ir-regular shaped dot.
            Typically with a red dot sight enhancement, you use enough brightness control to allow you to make out the dot in the shooting conditions that you have. The lower the setting you can have, the less distortion of the dot. Additionally, this allow you to have a better field of view through the sight, and encourage greater accuracy.

            Good luck..

            Also- The emitter does stick out slightly in the field of view.

            Again also- It looks like you are using a ARMs SIR, with a ARMS rear folding sight. If it is on the SIR, then you are hosed. There is no way to get that sight enhancement any lower. Unless you took the sight off the base, and shaved that down. but, there is not a great amount of room even for that.
            There is another way of raising back ups. but this would almost certainly mean changing to a different set.

            To help give you a little peace of mind. Lets say your sight enhancer failed, remember that just looking through the tube functions as a sight.
            You would be amazed at how accurate you can be just using the tube, no dot inside, as a sight.
            Then of course, why even have back ups then?....... Ahhh HA!.. See, my argument for do we really need back ups for emergency use?
            Last edited by Matt P; 12-31-2010, 8:31 PM.
            My WTB of Anything Glock 1-2 Generation, Tupperware, Manuals or Parts. Press Me

            Comment

            • #7
              Low-Pressure
              Senior Member
              • Sep 2009
              • 1758

              Originally posted by Res
              Thanks Low. Is your "laser emitter" flush, or does it jut out like this one? I ask because Marshall said it looks normal in the picture. But at 1/3 cowitness I the right shroud of the front sight is completely covered as well as the lower part of the blade.

              My emitter is on the 6 o'clock position. I do not use my irons with my red dot, so I d o not even notice the emitter.....
              Reading through the feedbacks a lot of users are using it as 1/3 co wotness with out problems...
              Try taking her out and see if it does bother you when using it on the field....
              If you are not happy with it, I'm quite sure Marshall will take it back....
              Good luck
              ...with liberty and justice for all. Void where prohibited, offer not valid everywhere, price may change. See Big Brother for details.
              Originally posted by zfields
              9mm might expand but .45 never shrinks!
              Originally posted by bwiese
              Constitutional rights are not dependent on your neighbors' opinions'.
              If you shop at Amazon.com please use the link below. A portion of your purchase goes to CGF.
              http://www.amazon.com/?_encoding=UTF...reative=390957

              Comment

              • #8
                tacticalcity
                I need a LIFE!!
                • Aug 2006
                • 10929

                Mine has the emiter in the same place but it does not cover my irons. I am running the same sight with the optional tall mount. My sights are Troy folding sights. Everything works great. I think the camera angle is making it worse than it is.

                Comment

                • #9
                  erratikmind
                  Member
                  • Feb 2010
                  • 325

                  I have a couple of the earlier version PA micro dots and the LED is at the 6 o'clock position. Marshall has moved the LEDs on the newer models to the 4:30 position in an attempt to improve on the co-witness of rifles.

                  I use mine on my on a Glock and a MK III.

                  Comment

                  • #10
                    Res
                    Senior Member
                    • May 2006
                    • 1633

                    Originally posted by tacticalcity
                    I think the camera angle is making it worse than it is.
                    No. I picked those pictures because that is exactly how it looks.

                    I'm just trying to figure out if this is how it's supposed to be, or if I got a defective one.

                    is this normal for the micro sight?


                    I have a standard front sight and an A.R.M.S. #40 Flip Up Rear Sight
                    Last edited by Res; 01-01-2011, 2:45 PM.
                    --------------------------------------------
                    Dusty Miller
                    Sacramento

                    Matthew Jackson Miller: 8-6-07 to 10-15-07
                    sigpic

                    Comment

                    • #11
                      Matt P
                      Veteran Member
                      • Jun 2006
                      • 3101

                      I feel your problems are unique due to the ARMs SIR platform you are using.

                      He has an elevated rail. If using a standard 30mm tubed reddot, you have to use a very low mount for it to get the proper co-witness, when attaching that style of sight to a ARMs SIR, or like that.
                      Since I never used a Micro with a SIR platform, I can only assume that with that micro type, he will be unable to get the sight any lower while using the ARMs style elevated rail.
                      My WTB of Anything Glock 1-2 Generation, Tupperware, Manuals or Parts. Press Me

                      Comment

                      • #12
                        Res
                        Senior Member
                        • May 2006
                        • 1633

                        Hi Matt

                        I'm not running an SIR. I just have the arms buis on a CMMG upper.




                        Marshall thinks that it could be because I don't have my sights zeroed. problem with that is, is that I can only move windage and not elevation w/ this sight, and moving the front sight is moot since the emitter is still covering the front shroud. If the led is supposed to be is high as it is (its not just the camera angle), then maybe that means somewhere, something might be canted like the rear sight or the quick detach mount.
                        --------------------------------------------
                        Dusty Miller
                        Sacramento

                        Matthew Jackson Miller: 8-6-07 to 10-15-07
                        sigpic

                        Comment

                        • #13
                          Matt P
                          Veteran Member
                          • Jun 2006
                          • 3101

                          Thanks for the side shot. I thought for sure it was a SIR.
                          I saw your optic with the low mount, and assumed you were using it with that mount on a SIR.
                          To easily get a relative good starting zero, take the upper off the lower.
                          Next remove the bolt carrier group.
                          Find a firm base, or something you can rest your upper on. I have used towels, a pillow, just something you can lay your upper on as if to rest it. You will need to be able to look down the bore, and also see through the sight.
                          It helps that whatever rest you use, the upper can maintain a position where it will not move, and you can look through the bore and sight without inducing movment.
                          Next, find an object outside (Be mindful that you will not have people walk in front of you, nor see you doing this. In essence, just be aware of where you do this. This can easily be done from home, apartment, as long as you are not in public view)
                          Find an object 25, 50, 100 yards away, whatever you choose. I try to use at least 50 yards.
                          You first want to center up the object as you look through the bore. This is very easily done.
                          Use the inner walls of the bore, the muzzle end, to help get the bore pointed at the your specific point of aim.
                          Now, look through your optic, and or open sights. Whichever one you want to bore sight, and help you get easily on paper.
                          You simply look through the bore, and the optic or sights, and make adjustments to sights/optic so they have the same point of aim as the bore.
                          There you go!
                          I can easily get on paper a 100 yards away when mounting an new optic/sight with this method.
                          It works very well. You can bore sight any firearm where you can look through the bore.

                          Try this Dusty and see where you stand.

                          One last thing. The Knights Arm 600 M flip up rear sights are the only rears I like to run. This is due to that they are a folding sight that also has elevation control. One of the very few back up irons that offer this, and fold also.

                          The REAL DEAL

                          An Alternative that will work to help save money
                          Last edited by Matt P; 01-02-2011, 3:35 PM.
                          My WTB of Anything Glock 1-2 Generation, Tupperware, Manuals or Parts. Press Me

                          Comment

                          • #14
                            Res
                            Senior Member
                            • May 2006
                            • 1633

                            Thanks Matt I'll do that. This morning I took the mount and turned it around just to see if there was a difference. It actually moved the sight over to the right just enough that I have a much clearer sight picture.

                            Thanks everyone for all the advice.
                            --------------------------------------------
                            Dusty Miller
                            Sacramento

                            Matthew Jackson Miller: 8-6-07 to 10-15-07
                            sigpic

                            Comment

                            • #15
                              gemini1
                              Senior Member
                              • Nov 2008
                              • 2230

                              So OP, have you resolve the issue of the dot blooming/exploding? I too just aquired a micro dot but its from a fellow member, so I have'nt emailed PA about my issue. The dot on mine at whatever intensity is blooming, funny thing is, if I look through it with my BUIS, then the dot is well, a dot, no exploding or blooming look. But I guess that defeats the purpose of having a RD if the rear sight has to be engage to give it a clear round dot.

                              Comment

                              Working...
                              UA-8071174-1