Unconfigured Ad Widget

Collapse

Scope leveling...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MarikinaMan
    Veteran Member
    • Nov 2015
    • 4864

    Scope leveling...

    My scope has a square block of aluminum in the middle where the turrets mount. You'll see it on this pic.



    My question is, is it ok to place the bubble level on that block instead of the turrets when leveling the scope to the rifle. The bolt on the turrets are not recessed and I feel that the block is a better platform. However, is the block aligned to the reticle?

    Thanks.
  • #2
    Mute
    Calguns Addict
    • Oct 2005
    • 8609

    Just use some feeler gauges between the scope and your mount. Simple and quick.
    NRA Benefactor Life Member
    NRA Certified Pistol, Rifle, Personal Protection In The Home, Personal Protection Outside The Home Instructor, CA DOJ Certified CCW Instructor, RSO


    American Marksman Training Group
    Visit our American Marksman Facebook Page

    Comment

    • #3
      sacrvrrat
      Member
      • Nov 2010
      • 425

      If you really want it level. Level the gun how you are going to hold it. Then hang a plumb bob out in front on the scope. Place the scope in the mount and rotate until the cross hairs match the plumb bob. If you are just going to use a level on the scope I would use the base not the turret.

      Comment

      • #4
        strongpoint
        Veteran Member
        • Dec 2010
        • 3115

        There's always this solution: Segway Reticle Leveler.

        .

        Comment

        • #5
          MarikinaMan
          Veteran Member
          • Nov 2015
          • 4864

          I see from the responses that the block (the base) is ok for leveling. I'll stick with the bubble levels and maybe run a plumb bob.

          Thanks for the replies.

          Comment

          • #6
            JMP
            Internet Warrior
            CGN Contributor - Lifetime
            • Feb 2012
            • 17056

            Originally posted by MarikinaMan
            My question is, is it ok to place the bubble level on that block instead of the turrets when leveling the scope to the rifle. The bolt on the turrets are not recessed and I feel that the block is a better platform. However, is the block aligned to the reticle?
            That's a funny looking scope, but yes, it would be fine to use a level on the block. That gets you close enough. Feeler gauges, as mentioned are the best way to level the scope because levels do not tell you that your rifle is out of alignment.

            Comment

            • #7
              NPFreedom
              Senior Member
              • Jan 2012
              • 1568

              Originally posted by strongpoint
              There's always this solution: Segway Reticle Leveler.

              I hate to say but i have that solution and i hate it. It is very hard to use. Its nice in theory but hard to eyeball.

              I like the level the rifle first then put another level on the scope solution. Also the plum bob works too. Just make sure there is no wind.
              Visit www.npfreedom.com for discounted firearm parts and accessories

              Comment

              • #8
                strongpoint
                Veteran Member
                • Dec 2010
                • 3115

                Originally posted by wirespeed
                I hate to say but i have that solution and i hate it. It is very hard to use. Its nice in theory but hard to eyeball.
                I just used mine the other night, no problem at all. Different strokes, I guess.
                .

                Comment

                • #9
                  MarikinaMan
                  Veteran Member
                  • Nov 2015
                  • 4864

                  Originally posted by JMP
                  That's a funny looking scope, but yes, it would be fine to use a level on the block. That gets you close enough. Feeler gauges, as mentioned are the best way to level the scope because levels do not tell you that your rifle is out of alignment.
                  The feeler gauge is easy enough, and it'll work for normal use. I'm trying to build a long range AR. I saw a few reports online of feeler gauge installations being off when it comes to shooting long range. I watched a video on the process. The gauge is moves freely, the scope is loose and it relies on a friction fit to the rail. I tend to believe there is room for more error.

                  In mounting the scope, I'm using multiple bubble levels to align the scope and the rifle. I also utilize a barrel vise in conjunction with a gun vise to hold the rifle in a very solid fixed position during the process. It's worked very well on my other rifles. It takes me 15 minutes to mount a scope including torquing all bolts. Ain't no thang.

                  I've seen many houses and large buildings built with bubble levels and clear hose water lines. I have no doubt it's a fairly accurate system of measure.
                  Last edited by MarikinaMan; 01-28-2016, 10:18 PM.

                  Comment

                  • #10
                    FMJBT
                    Veteran Member
                    • Mar 2007
                    • 4888

                    The feeler gauge method works pretty well, as long as your reticle isn't canted within the erector tube. With the feeler gauges and even bubble levels, you are only leveling the scope body to the rifle, the reticle may still be tilted. Depending on how you shoot, at that point you have to decide which element you want level with the rifle. If you shoot using mostly holdovers you'll want the reticle itself level with the rifle. If you dial in elevation corrections though you'll want the scope body and turrets to be level, so the erector tube will travel in line with the bullets trajectory.

                    In a perfect world, every scope would have a reticle perfectly leveled with the scope body and turrets. Unfortunately it's pretty common to find scopes that are slightly off, even high end optics are not immune to this problem.
                    U.S. Navy (Retired) 1994-2015

                    Comment

                    • #11
                      MarikinaMan
                      Veteran Member
                      • Nov 2015
                      • 4864

                      Originally posted by FMJBT
                      The feeler gauge method works pretty well, as long as your reticle isn't canted within the erector tube. With the feeler gauges and even bubble levels, you are only leveling the scope body to the rifle, the reticle may still be tilted. Depending on how you shoot, at that point you have to decide which element you want level with the rifle. If you shoot using mostly holdovers you'll want the reticle itself level with the rifle. If you dial in elevation corrections though you'll want the scope body and turrets to be level, so the erector tube will travel in line with the bullets trajectory.

                      In a perfect world, every scope would have a reticle perfectly leveled with the scope body and turrets. Unfortunately it's pretty common to find scopes that are slightly off, even high end optics are not immune to this problem.
                      Thanks to the all the replies above. They were really informative.

                      Comment

                      • #12
                        Mute
                        Calguns Addict
                        • Oct 2005
                        • 8609

                        I've used the feel gauge method for years on multiple rifles. Only once did I have a problem and it was with a Leupold that had a canted reticle. The bubble level works also. I used to do it that way but have stuck with the gauges since it's worked out pretty well and made scope mounting so much simpler.
                        NRA Benefactor Life Member
                        NRA Certified Pistol, Rifle, Personal Protection In The Home, Personal Protection Outside The Home Instructor, CA DOJ Certified CCW Instructor, RSO


                        American Marksman Training Group
                        Visit our American Marksman Facebook Page

                        Comment

                        • #13
                          MarikinaMan
                          Veteran Member
                          • Nov 2015
                          • 4864

                          Originally posted by Mute
                          I've used the feel gauge method for years on multiple rifles. Only once did I have a problem and it was with a Leupold that had a canted reticle. The bubble level works also. I used to do it that way but have stuck with the gauges since it's worked out pretty well and made scope mounting so much simpler.
                          I believe it. Im giving myself room for error. I can set a fishing drag by feel and torque specific bolts to specific applications to spec. It's all in the user

                          Comment

                          • #14
                            KillZone45
                            Veteran Member
                            • Sep 2009
                            • 2570

                            Just but a Spuhr mount.
                            Nikita Khrushchev said"We can't expect the American People to jump from Capitalism to Communism, but we can assist their elected leaders in giving them small doses of Socialism, until they awaken one day to find that they have Communism. "

                            Comment

                            • #15
                              GiddyHitch
                              Member
                              • Mar 2014
                              • 274

                              Arisaka came out with a nice set of scope leveling tools last year:

                              Comment

                              Working...
                              UA-8071174-1