Unconfigured Ad Widget

Collapse

20 MOA scope base?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tjdonn
    Junior Member
    • Dec 2013
    • 44

    20 MOA scope base?

    I am confused on what this is for. From what I can gather it is so the scope sits angled up a bit? Would this be good for a hunting set up with a standard 3x9 on it?
  • #2
    Merc1138
    I need a LIFE!!
    • Feb 2009
    • 19742

    No, it's so the front of the scope is angled down a bit, so you can still adjust your elevation via the turret for shooting longer distances without running out of room(or holding over at the edge of the glass).

    I really doubt you'd need or want one for hunting.

    Comment

    • #3
      Cowboy T
      Calguns Addict
      • Mar 2010
      • 5725

      Merc's right. It's only needed if you're shooting out past, say, 600 yards with a .308 Win. You can certainly still shoot 100 yards with that 20 MOA base. You will simply need to either hold over, or dial your scope for the shot. I have them on two of my .308's, both of which also use 3-9x40 scopes, and you can hit 1,000 with such a setup.

      How far do you think you'll be shooting?
      "San Francisco Liberal With A Gun"
      F***ing with people's heads, one gun show at a time. Hallelujah!
      http://www.sanfranciscoliberalwithagun.com (reloading info w/ videos)
      http://www.liberalsguncorner.com (podcast)
      http://www.youtube.com/sfliberal (YouTube channel)
      ----------------------------------------------------
      To be a true Liberal, you must be 100% pro-Second Amendment. Anything less is inconsistent with liberalism.

      Comment

      • #4
        JMP
        Internet Warrior
        CGN Contributor - Lifetime
        • Feb 2012
        • 17056

        Originally posted by tjdonn
        From what I can gather it is so the scope sits angled up a bit?
        This is a common misconception as it may be counter intuitive at first thought. The cant in the base is to angle the scope DOWN. Think of it like this, to shoot a further target, you must aim your barrel above the target to compensate for the drop. However, the scope does not have the trajectory of a bullet and will remain in a straight line. Thus, when you are shooting where a lot of elevation is needed, when you dial to shoot higher, you aim your scope lower.

        That said, a 20 MOA base rarely hurts so long as you have at least 65 MOA of total travel. If you don't have enough elevation range in your scope, you can have issues. Thus, if it isn't needed, which it generally isn't for close up shooting (less than 1,000 yards), many will go without, then your picture stays along the axis of the scope, which provides for the best picture and reliable tracking.

        For scopes that have small knobs and a lot of turns to the top, if they do not have a zerostop, I'd rather put some cant into the base to help you keep from dialing past zero when you go back down.

        Comment

        • #5
          timbo399
          Senior Member
          • Jul 2010
          • 1765

          Originally posted by JMP
          This is a common misconception as it may be counter intuitive at first thought. The cant in the base is to angle the scope DOWN. Think of it like this, to shoot a further target, you must aim your barrel above the target to compensate for the drop. However, the scope does not have the trajectory of a bullet and will remain in a straight line. Thus, when you are shooting where a lot of elevation is needed, when you dial to shoot higher, you aim your scope lower.

          That said, a 20 MOA base rarely hurts so long as you have at least 65 MOA of total travel. If you don't have enough elevation range in your scope, you can have issues. Thus, if it isn't needed, which it generally isn't for close up shooting (less than 1,000 yards), many will go without, then your picture stays along the axis of the scope, which provides for the best picture and reliable tracking.

          For scopes that have small knobs and a lot of turns to the top, if they do not have a zerostop, I'd rather put some cant into the base to help you keep from dialing past zero when you go back down.
          Very interesting info for a guy like me who's just planning on getting my first scoped rifle- all rifle shooting ever done past 5 years w my ARs and M1A Scout have been using irons.

          Building up a semi .308 w scope- never even used scope before but understand SFP/FFP etc and going w MOA/MOA and narrowed down to a few in the $1200-1500 range. Not looking to shoot past 600-700 yrds so probably no need for 20MOA base , plan to get strong one piece mount like Warne Tactical since it's a semi and one piece look cooler!!!. No need for QD since won't be changing optics. Have my SCAR 17 w ACOG for less accurate range fun, oh and of course for battle.

          Comment

          • #6
            FourT6and2
            Senior Member
            • Dec 2012
            • 1928

            Here's an example. I'm building a bolt-action in 6.5CM. For the Hornady 140 A-Max:

            Velocity: 2710
            BC: 0.585 (G1)
            100-yard zero

            You only need 9.3 MILs of come up at 1,000 yards. No need for a canted base with the majority of scopes out there. For example, Kahles 624i has 25 MILs of adjustment. But at 1,500 yards, you need 19.6 MILs come up. Depending on your zero, you might not have enough adjustment if you're in the center of your scope's range. Then a canted base would be needed. You rarely need to dial a scope UP from your zero. So any adjustability in that direction once zeroed is basically wasted. A canted base allows you to move the scope farther in the opposite direction for your zero, letting you make use of that unused adjustability should you need it.

            I haven't read anything about a canted base (like 20 MOA) affecting your scope's sight picture or image quality. That's news to me...
            Last edited by FourT6and2; 08-24-2015, 3:40 AM.

            Comment

            Working...
            UA-8071174-1