So do I have to sell my L1A1 out of state now??

[munkeeboi]

I make a wrap for the L1A1. Just add the wrap and remove the flash hider and then you are good to go. No permanent modifications or welding needed and let's the next owner decide how they want to configure it

[-hanko]

Wouldn't it be easier to just fill in the slot on the maglock so you can't push on the mag release?

Easiest to replace the mag lock point and spring with a short length of brass rod...it also makes it impossible to press the mag release. Does California require welding or silver soldering?

[-hanko]

hay -hanco...look a izzy L2A2 SUIT ! [ATTACH]603495[/ATTACH]

I need one...my SUIT is a Brit. I need to get off my tail and make a tritium light source. It's a great sight for close encounters and the aiming post doesn't block out the lower part of the target below poa.

[santacruzgunner]

Use the info, don't use it. Make a kit out of it and bomb a mosul cave. I really dont GAF.

Lol

[lavey29]

Is this the situation? I have an L1A1 (British Army version of the FAL) built on a an Entreprise receiver with Enfield parts, including the L2A2 SUIT sight. AM I correct in thinking that I now have to sell out of state?

I had the same rifle, registered pre-ban from the 90's and yes I had to sell it out of state.

[scamp62]

HANCO, I have an Izzy on my FAL and I had to replace the tritium in my sight
I'm looking for an Brit sight..hell i would just be happy to get the Brit, data label.

[-hanko]

HANCO, I have an Izzy on my FAL and I had to replace the tritium in my sight
I'm looking for an Brit sight..hell i would just be happy to get the Brit, data label.

Mine was ~ $300 with new mounting hardware and the original hardware was included. I'd advise haunt the FAL Files until you find one. I've got no idea what they're going for lately.

[SloChicken]

Easiest to replace the mag lock point and spring with a short length of brass rod...it also makes it impossible to press the mag release. Does California require welding or silver soldering?

This is a great idea!

I wonder why DSA went through the trouble of welding that little bead in the receiver when they were selling the CA legal fixed mag STGs (That is what I have, and how I know of the weld).
It wasn't much trouble to remove, a quick dremel, and a file to finish and viola.
However, your way just makes so much sense.
This is exactly how I blocked the plunger on my old Sage M1A Mod ) stock.

I am running my little OSW featureless, but if I go back to a stripper clip config (Acog is blocking it now) I will certainly go this way about things.
So much easier.

[-hanko]

This is a great idea!

I wonder why DSA went through the trouble of welding that little bead in the receiver when they were selling the CA legal fixed mag STGs (That is what I have, and how I know of the weld).
It wasn't much trouble to remove, a quick dremel, and a file to finish and viola.
However, your way just makes so much sense.
This is exactly how I blocked the plunger on my old Sage M1A Mod ) stock.

I am running my little OSW featureless, but if I go back to a stripper clip config (Acog is blocking it now) I will certainly go this way about things.
So much easier.

No idea as to why DSA went with welding.

My FAL's were not registered in California as "AW's" (my choice)...I saw the idea on the FAL Files and posted it here since it is quick, cheap, and no welding involved.

[God Bless America]

Easiest to replace the mag lock point and spring with a short length of brass rod...it also makes it impossible to press the mag release. Does California require welding or silver soldering?

Does not suffice. Can still remove mag without disassembling action.

[-hanko]

Does not suffice. Can still remove mag without disassembling action.

Meaning that having to remove the screw that holds both the bolt release and mag release is not defined as "disassembling the action"??

[God Bless America]

Meaning that having to remove the screw that holds both the bolt release and mag release is not defined as "disassembling the action"??

No, I do not believe it is. And I have an FAL clone with a disabled mag release, so I am not idly chattering on this issue.

I think you describe 'disassembling the mag catch' (yes and bolt release), not the action.

[Sniper3142]

Is this the situation? I have an L1A1 (British Army version of the FAL) built on a an Entreprise receiver with Enfield parts, including the L2A2 SUIT sight. AM I correct in thinking that I now have to sell out of state?

Or you could just register it (I believe).

[God Bless America]

Or you could just register it (I believe).

That's my plan.