Hi, I'm new to this forum, but not the gun industry. Just had a custom 243wssm built on a remington 721 action. Got to take it to the range today and my first attempt with reloads proved to be very promising. 42grs of 4350 with an 80gr gmx bullet seemed to group the best. Wanted to see if anyone else in CA had any luck/love for the chubby little winchester cartridge?
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
243wssm
Collapse
X
-
That is One Bad Arse Round !!
I've only come across a few of the Brass in my Harvesting
What kind of FPS do you get out of that round ??
How's the recoil ??
What Max range ?
Inquireing Minds want to know !!!!!!!!!!!!!!!!!!!!!!--------------------------------------------------------------
I miss the Good 'ol days of Cal -GunsComment
-
Well this is my first wssm. The accuracy I was able to achieve without any tweeks to my loads and with both 55gr noslers and the 80gr gmx was exciting.
I haven't been able to check the fps yet. Today was just the first day out with it and honestly I was just trying to figure out where to start with working up a load. The recoil is very mild. I have plenty of big calibers, but I like to hunt with things like the 260 rem and other soft shooting rounds, the 243 wssm defiantly fits the bill and I'm expecting to put a hurting on some pigs on my next hunt. Will be in llano Texas the 20th to kick off a week long hunt. As far as max range goes, It was a laser to about 350 yards, will try farther on my next range visit. Today I just ran out of timeComment
-
Thanks for the Info.
I always thought that it's an Interesting round and wondered how it would work out in the real world
Congrats on the set-up--------------------------------------------------------------
I miss the Good 'ol days of Cal -GunsComment
-
The reasons the 243 wssm got bad reputation is very thick brass and the short freebore Winchester used in order to get the heavy bullets to fit into a factory magazine.
These can both be eliminated when re-barreling by ordering a custom reamer. I went with a 0.104 freebore and a 0.268 neck on mine and it shoots very well.Lynn Dragoman, Jr.
Southwest Regional Director
Unlimited Range Shooters Association (URSA)
www.unlimitedrange.org
Not a commercial business.
URSA - Competition starts at 2000 yards!Comment
-
Mine is on a Savage Precision Target Action, 1:8" twist Brux 26" Savage Varmint Contour barrel. Came as a prefit from Sharp Shooter Supply, also used one of their pillar bedded Classic Varmint stocks. Use the brass just with minor modifications; trimmed to length, primer pockets uniformed and deburred. Load it with 62 grain Barnes Varmint Grenades over 47.5 to 49.5 grains of Ramshot Hunter, ignited by Wolf Large Rifle Primers. If I ran out of Wolf primers I'd substitute Remington 9-1/2 or WLRP. Bullets are seated to 2.240" to the tip, or 2.755" using a Sinclair comparator. The 49.5 grain load became my favorite poking along at 3,587 fps.
I tried turning the necks to a uniform thickness, but that had no effect on accuracy. 100 Yard ten shot groups on overcast still-air days have run small enough to confound me, 7 of ten shots into 0.284 inches, while the average is between 0.33" and 0.5" all dependent on my ability to read conditions and trigger control (not easy being buffeted about sandwiched between a .50 BMG and .338 Lapua at the range). In the field a miss is a rare thing out to 300 yards or so, about the limit of my age and skill.
When I saw the seasonal run of brass I bought 1,500 cases. Ground squirrels feeding in irrigated alfalfa completely vanish upon impact, leaving a patch of ground that appears rototilled, with a small tunnel cut through the alfalfa behind where they stood. Near misses kill from shrapnel, pebbles and sand grains. On dry ground they just pop as usual.Comment
-
Sounds a lot like my 243AI. What velocities do you guys get?Comment
-
Wrangler John
I went with the 0.268 neck so I could load the round down without all the soot on the neck and shoulder area.
I bought one of each in 223 and 243 when they first came out and the necks were as thick as my 50 bmg cases at 0.020 per side. With the necks turned I can load them light and not collapse any brass.
I am using the 103 grain Spencer vld bullets and if you look at factory rounds the bullet is seated so deeply it barely has any bullet sticking out so I lengthened the freebore when I ordered up the reamer.Lynn Dragoman, Jr.
Southwest Regional Director
Unlimited Range Shooters Association (URSA)
www.unlimitedrange.org
Not a commercial business.
URSA - Competition starts at 2000 yards!Comment
Calguns.net Statistics
Collapse
Topics: 1,870,776
Posts: 25,175,830
Members: 358,862
Active Members: 5,399
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 31110 users online. 145 members and 30965 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment