Unconfigured Ad Widget

Collapse

Why bother ?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • killshot44
    Veteran Member
    • Nov 2009
    • 4072

    Why bother ?

    F*cks given = Zero
    Last edited by killshot44; 08-09-2014, 6:04 PM.
  • #2
    phish
    Veteran Member
    • Jan 2006
    • 3089

    The pillars on my factory Savage stocks were the same. Aftermarket triggers, barrels and stocks, why not pillars?

    Comment

    • #3
      6mmintl
      Veteran Member
      • Apr 2008
      • 4822

      That is typical for those stocks, also note the overmold on v block, scrape it off and re-bed the whole action and recoil lug if you want enhanced accuracy.

      Ive done about 15 of those the past 12 years.

      Comment

      • #4
        MongooseV8
        Veteran Member
        • Apr 2010
        • 4426

        With the aluminum block I usually just bed the recoil lug, but a skim bed would be even better since Remington cant decide what od they want to machine their receivers.

        Comment

        • #5
          Fjold
          I need a LIFE!!
          • Oct 2005
          • 23093

          There are a couple of different ways pillars are used.

          Generally in custom work, the action rests on the pillars and it holds the action to the pillar when tightened and bedding is done to match the height of the pillars.

          In mass produced stocks, the bedding is put in hopefully to match the action and then pillars are installed in the stock. The pillars are simply there to keep you from crushing the stock with the action screws and give a consistent surface for torque.

          I always recommend skim coating the bedding area in mass produced stocks to insure a good fit.
          Frank

          One rifle, one planet, Holland's 375




          Life Member NRA, CRPA and SAF

          Comment

          • #6
            MongooseV8
            Veteran Member
            • Apr 2010
            • 4426

            Noice!

            Comment

            • #7
              ar15barrels
              I need a LIFE!!
              • Jan 2006
              • 57199

              Originally posted by killshot44
              Took apart my buddy's 700 today(no idea of the model, its a .308 w/stainless barrel, thin profile, in what looks to be a B&C stock) and couldn't believe what I saw.

              Take a look at the pillars, they are waaaaaaay short of reaching the action and are below the aluminum bedding surface!

              Not only that but the pillars have such a large I.D. that there's a lot of slop between the pillars and the action screws.
              The pillars are larger on the bottom and actually have a shoulder that stops them in the bedding block.
              That is how HS and B&C set the depth of the bottom metal before they fill the stock with foam.
              In that design, the pillars are not supposed to bear on the action as the action is bearing on the bedding block.
              The bottom metal and pillars then bear on the bedding block as well when the screws are tightened.
              There is absolutely nothing wrong with those pillars.

              The pillar holes should be 1/16" LARGER than the screws so that the screws never come to bear on the pillars.
              Make sure you clean out all the bedding material and tape when you are done so that the screws are completely free floating on the sides of the screws.
              Only the head of the screw should touch the bottom metal.
              Randall Rausch

              AR work: www.ar15barrels.com
              Handguns: www.handgunbarrels.com
              Bolt actions: www.700barrels.com
              Foreign Semi Autos: www.akbarrels.com
              Most work done while you wait on a scheduled shop visit.

              Comment

              • #8
                ar15barrels
                I need a LIFE!!
                • Jan 2006
                • 57199

                Originally posted by killshot44
                The action rested on the stock's sides with a gap of over .200" between the inserts and the action. (see photo two, you can see the edge of the stock where the action rests, well above the aluminum insert)
                I find 0.200" that hard to believe.
                It would be expected for a round shape to touch the sides of a V-Block bedding system.
                To expect perfect contact at the bottom of a V-block would eliminate the stability that a V-block gives you though.
                Randall Rausch

                AR work: www.ar15barrels.com
                Handguns: www.handgunbarrels.com
                Bolt actions: www.700barrels.com
                Foreign Semi Autos: www.akbarrels.com
                Most work done while you wait on a scheduled shop visit.

                Comment

                • #9
                  ar15barrels
                  I need a LIFE!!
                  • Jan 2006
                  • 57199

                  Originally posted by killshot44
                  Sorry if I wasn't clear, there wasn't a V-block in the stock.

                  In the first photo, it shows how the contour of the aluminum insert (close to the action diam) is smaller than the inside contour of the stock. The gap I was referring to included both sides of the action.
                  Actually, that IS a V block, perhaps you just didn't see it...

                  The smaller diameter of the aluminum bedding block causes the very slightly larger diameter receiver to settle on the edges of the aluminum bedding block when the screw is tightened down.
                  Last edited by ar15barrels; 08-09-2014, 6:39 PM.
                  Randall Rausch

                  AR work: www.ar15barrels.com
                  Handguns: www.handgunbarrels.com
                  Bolt actions: www.700barrels.com
                  Foreign Semi Autos: www.akbarrels.com
                  Most work done while you wait on a scheduled shop visit.

                  Comment

                  • #10
                    Thorax
                    Banned
                    • Apr 2010
                    • 915

                    All I got from the first post was "sales pitch" with a heavy attempt at trying to be subtle and failing miserably at it.

                    If you honestly have bedded more than 2 B&C stocks or 2 HS Precision stocks, you have seen this before, why act surprised ??????

                    If you haven't bedded 2 stocks before....wtf are you trying to sell your work here ?????

                    Randall is exactly correct in his posts when talking about B&C.
                    HS has a half of an octagon shape to the bedding block, is that the next "can you believe this" post ?

                    Comment

                    • #11
                      wooger
                      CGN/CGSSA Contributor - Lifetime
                      CGN Contributor - Lifetime
                      • Nov 2006
                      • 1380

                      Lol. I machine my pillars off and bed over anyway.
                      Last edited by wooger; 08-10-2014, 2:17 PM.
                      vatr slapn

                      Comment

                      • #12
                        toby
                        Banned
                        • Jan 2010
                        • 10576

                        Was it something that was said?

                        Comment

                        • #13
                          ar15barrels
                          I need a LIFE!!
                          • Jan 2006
                          • 57199

                          Originally posted by toby
                          Was it something that was said?
                          Some people can't take constructive criticism.
                          Randall Rausch

                          AR work: www.ar15barrels.com
                          Handguns: www.handgunbarrels.com
                          Bolt actions: www.700barrels.com
                          Foreign Semi Autos: www.akbarrels.com
                          Most work done while you wait on a scheduled shop visit.

                          Comment

                          Working...
                          UA-8071174-1