Unconfigured Ad Widget

Collapse

HELP! - Savage Trigger Damaged

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Phil3
    Senior Member
    • Oct 2008
    • 2249

    HELP! - Savage Trigger Damaged

    I was handling my Precision Target Action with barrel attached, and I bumped the exposed trigger on the carpeted floor. Not hard at all, but hard enough where the trigger does not work. The bolt does not even want to lift, but you can if forced. Do not want to do that again. It is not cocked but the trigger is solid, and will not move. The safety blade moves OK. The bolt release only moves a little bit.

    Can someone help me troubleshoot? I am really distressed about this, so really hope I didn't muck anything up too badly. Nothing appears bent, but cannot recall how it all supposed to look.


    Phil
  • #2
    67Cuda
    Senior Member
    • Oct 2013
    • 1727

    So you snagged the trigger on the carpet?

    Sounds like you might have over extended the trigger rearward. Does it look like that?
    If so, push it back forward.

    Somebody will chime in with a solution. Other than that, take it to a gunsmith.
    Originally posted by ivanimal
    People that call other member stupid get time off.
    So much for being honest.

    Comment

    • #3
      Phil3
      Senior Member
      • Oct 2008
      • 2249

      It did not snag. The bottom of the trigger hit the carpeted floor. The barreled action did not fall, I was holding it where that end was heavy and it sort of sank to the floor. I didn't think anything of it until I tried to operate bolt. Pics here.



      I did get bolt out, but it will not go back in. I do not know why. I am guessing that little piece in the bottom of the bolt raceway, but do not know why.

      Thank you.

      Phil
      Last edited by Phil3; 09-05-2018, 2:15 PM.

      Comment

      • #4
        baih777
        CGN/CGSSA Contributor
        CGN Contributor
        • Jul 2011
        • 5680

        Remove the e-clip for the trigger. Tap the pin out.
        Just pull the trigger out quarter of an inch and reinstall.

        I think you just over traveled the trigger. And it's hung up.
        Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
        I really miss the good old Pomona Gun Shows.
        I'm Back.

        Comment

        • #5
          Phil3
          Senior Member
          • Oct 2008
          • 2249

          In an embarrassing display of stupidity, I failed to notice that the bolt rotating part adjacent to the lugs (do not what that is called) was rotated 180 degrees, and will not go into raceway. It does now, but sometimes, makes a weird double click when closing bolt. Trigger works, but bolt lift even heavier than it was.

          Phil

          Comment

          • #6
            Dark Hunt
            Member
            • Sep 2016
            • 420

            Originally posted by Phil3
            the bolt rotating part adjacent to the lugs

            Phil
            Gas Baffle - it blocks the bolt raceway when the bolt lugs are rotated closed to prevent any escaping gases from a cartridge failure from blasting into your face.


            You probably bent your trigger.
            NRA Endowment Life Member

            Comment

            • #7
              ar15barrels
              I need a LIFE!!
              • Jan 2006
              • 57198

              Originally posted by Phil3
              I was handling my Precision Target Action with barrel attached, and I bumped the exposed trigger on the carpeted floor. Not hard at all, but hard enough where the trigger does not work. The bolt does not even want to lift, but you can if forced. Do not want to do that again. It is not cocked but the trigger is solid, and will not move. The safety blade moves OK. The bolt release only moves a little bit.

              Can someone help me troubleshoot? I am really distressed about this, so really hope I didn't muck anything up too badly. Nothing appears bent, but cannot recall how it all supposed to look.
              Carpet strikes again.
              Randall Rausch

              AR work: www.ar15barrels.com
              Handguns: www.handgunbarrels.com
              Bolt actions: www.700barrels.com
              Foreign Semi Autos: www.akbarrels.com
              Most work done while you wait on a scheduled shop visit.

              Comment

              • #8
                russ69
                Calguns Addict
                • Nov 2009
                • 9348

                It's a good thing Army barracks aren't carpeted.
                sigpic

                Comment

                • #9
                  JTROKS
                  I need a LIFE!!
                  • Nov 2007
                  • 13093

                  Originally posted by Phil3
                  In an embarrassing display of stupidity, I failed to notice that the bolt rotating part adjacent to the lugs (do not what that is called) was rotated 180 degrees, and will not go into raceway. It does now, but sometimes, makes a weird double click when closing bolt. Trigger works, but bolt lift even heavier than it was.

                  Phil
                  Are you lifting the bolt while action is out of the stock?
                  The wise man said just find your place
                  In the eye of the storm
                  Seek the roses along the way
                  Just beware of the thorns...
                  K. Meine

                  Comment

                  • #10
                    k1dude
                    I need a LIFE!!
                    • May 2009
                    • 16266

                    Originally posted by ar15barrels
                    Carpet strikes again.
                    LOL.
                    "Show me a young conservative and I'll show you a man without a heart. Show me an old liberal and I'll show you a man without a brain." - Sir Winston Churchill

                    "I would remind you that extremism in the defense of liberty is no vice! And let me remind you also that moderation in the pursuit of justice is no virtue!" - Senator Barry Goldwater

                    Comment

                    • #11
                      Phil3
                      Senior Member
                      • Oct 2008
                      • 2249

                      Originally posted by JTROKS
                      Are you lifting the bolt while action is out of the stock?
                      Yes. It behaves the same in or out of stock.

                      Phil

                      Comment

                      • #12
                        shafferds
                        Senior Member
                        • Feb 2008
                        • 1970

                        Didn't you read the other thread . . Never drop your gun on the carpet.

                        Is the trigger still straight or slanted? If bent it could be binding.

                        Comment

                        • #13
                          mattt
                          Senior Member
                          • May 2009
                          • 1350

                          Remove rear allen screw carefully on bolt .Bolt will loosen up.Then remove bolt . Put bolt back together the right way and put back in.Once you do it once and see how bolt /trigger work together it will be easy second time.you may have to remove trigger ,Not rocket science. Try you tube good luck.
                          Last edited by mattt; 09-06-2018, 6:01 PM.

                          Comment

                          • #14
                            sigstroker
                            I need a LIFE!!
                            • Jan 2009
                            • 19991

                            Bolt disassembly:


                            Remove the trigger:

                            Comment

                            • #15
                              LynnJr
                              Calguns Addict
                              • Jan 2013
                              • 7959



                              Phil
                              Here is what your trigger looks like in individual pieces. I gave my factory trigger away and had Shaun Brady do his magic on a SSS competition trigger.
                              Believe it or not here is what I would do and I know it sounds weird.
                              Lay on your back and cycle the bolt a bunch of times upside down. Savages get adjusted upside down. On my gun the rear most spring set the triggers pull weight but it would move or drift over time. I used a dab of clear fingernail polish to keep it from turning.
                              If that doesn't work become friends with Shaun.
                              I say that because I bought a bolt lift kit for my savage and it hasn't been shot since I lost one part that has since been replaced.
                              Last edited by LynnJr; 12-20-2018, 11:54 AM.
                              Lynn Dragoman, Jr.
                              Southwest Regional Director
                              Unlimited Range Shooters Association (URSA)
                              www.unlimitedrange.org
                              Not a commercial business.
                              URSA - Competition starts at 2000 yards!

                              Comment

                              Working...
                              UA-8071174-1